• Journal of Advanced Navigation Technology
• /
• v.6 no.4
• /
• pp.312-317
• /
• 2002

This paper presents a graphical design method for a low noise amplifier using the match circles plotted in the ${\Gamma}_{IN}$ plane on the smith chart. Each circle would be useful for reducing some trial and error efforts resulting from making a trade-off for an optimized performance of a single stage amplifier. A design example is presented to illustrate the design procedure.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.8
• /
• pp.781-787
• /
• 2004

In this paper, a novel dual and wide band aperture stacked patch antenna for Cellular/PCS/IMT-2000 base station is presented. It consists of single microstrip patch having notches along the radiating patch, two dielectric substrates and a form material. To achieve wide band characteristic, we utilize the coupling effect between the notched patch and the resonant aperture in the ground plane and by properly cutting notches on the patch, an aperture stacked patch antenna could be designed to yield dual frequency operation. By the proper choice of resonant aperture size and height of a foam material, dual and wide band characteristic could be realized the measured impedance bandwidth(1:1.5 VSWR) of designed antenna at lower band(860 MHz) reaches 77 MHz and covers the Cellular CDMA band(824∼894 MHz). The measured impedance bandwidth(1:1.5 VSMR) of the designed antenna at upper band(1,960 MHz) is about 550 MHz and covers both the PCS band(1,750∼l,870 MHz) and the for-2000 band(1,920∼2,170 MHz). Good broadside radiation with high gain(5.65∼7.4 dBi) characteristics have also been observed.

• Journal of the Korea Society of Computer and Information
• /
• v.5 no.2
• /
• pp.115-120
• /
• 2000

This papers describes two low-noise amplifiers that use the Hewlett-Packard ATF-10236 low noise GaAs FET device, The actual measured performance of the amplifiers compares favorably to that predicted by the computer simulation(ADS) the noise figure of the 1575MHz amplifier was measured at 1.78dB which is lower that 2dB as specified. Measurement gam measured 33.0075dB which is within 35dB$\pm$0.5㏈ of the GPS specification. Network Analyzer(HP8510) is used to measure all the s-parameters and Noise Figure meter(HP8970B) is used to measure noise figure. As the result of experiment, gain, input VSWR, output VSWR is within the GPS specification sufficiently.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.9 s.100
• /
• pp.917-925
• /
• 2005

In this paper, the quad-band antenna for mobile handsets is proposed and developed. The operating frequency bands include GSM(880 MHz${\~}$960 MHz), GPS(1,575 MHz$\pm$10 MHz), DCS(1,710 MHz${\~}$l,880MHz), and PCS(1,850 MHz${\~}$l,990 MHz). The proposed antenna consists of a feed line, a shorting post, and a radiating element of the feed loop. The multi-band operation is achieved by using the fundamental and higher resonant modes of the radiating element. Based on analysis of the current distribution on the radiator, the resonant frequency of each mode can be adjusted by adding the different sizes of slots on the radiator. The radiator of the feed loop is designed to be symmetrical so that the energy is symmetrically distributed on the radiator, which results in omni-directional radiation pattern. The ground plane under the radiator is removed in order to improve the bandwidth. The measured impedance bandwidths are $10.1\%$ in GSM band(VSWR<2.5), $26.8\%$ in GPS band, and DCS/US-PCS bands(VSWR<2.5), respectively. The maximum gains on the H-plane of the fabricated antenna are measured about -0.37 dBi${\~}$2.55 dBi for all operating frequency bands.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.1-7
• /
• 2016

In this paper, the design methodology of a corrugated conical horn antenna is proposed to be obtain wide-band properties over the full range of frequencies in the Ku-band. In order to improve the properties of the corrugated conical horn antenna, such as its gain, VSWR, co-polarization to cross-polarization ratio and wide-bandwidth, two types of mode matching converters are implemented within it. One is located at the end of the circular waveguide, while the other is positioned in front of the horn-flare section. The properties of the antenna are analyzed and compared according to the position of the proposed converters through simulations. In the comparison of the antenna performance in the case where the VSWR, co-polarization to cross-polarization ratio and antenna gain over the Ku band of 12-18 GHz are less than 2, greater than 30dB and 20dB respectively, the former antenna exhibits greater stability and a wider frequency band than the latter from the viewpoint of transmitting and receiving signals simultaneously. Therefore, considering the gain, VSWR, radiation pattern and bandwidth, the horn antenna structure in which the mode matching converter is implemented inside the circular waveguide has better performance than the other.

• Journal of the Korea Knowledge Information Technology Society
• /
• v.12 no.4
• /
• pp.539-550
• /
• 2017

In this paper, we designed, fabricated and tested an UHF band cylindrical dipole array antenna. In the proposed antenna, cylindrical dipoles were vertically arranged in four stages. A parallel structure feeding circuit was installed inside the cylindrical dipole and mounted so as to be broadband matching. The feeding circuit was installed at the center of the cylindrical dipole to optimize the gain flatness characteristic of the azimuth direction omnidirectional radiation pattern. Minimizing the difference between the signals branched from the feeding circuit and realizing the symmetry of the radiation pattern. The required specifications are more than 11.2% bandwidth in UHF band, above 6dBi antenna gain, standing wave ratio of 2:1 or less, less than ${\pm}1dB$ gain flatness in azimuth radiation pattern, more than 13 degrees in elevation radiation pattern of 3dB beamwidth. We confirmed the possibility of implementation through M&S and verified the result of M&S through production and testing. The test results are 11.2% bandwidth in the UHF band, 6.30 to 8.31 dBi gain, 1.53:1 standing wave ratio or less, within ${\pm}0.2dB$ gain flatness in the azimuth radiation pattern, elevation radiation pattern of 3dB beam width was 15.62 to 15.84 degrees. The test result meets all requirements specifications.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.11
• /
• pp.891-899
• /
• 2013

This paper suggests a test and evaluation procedure of conformal load-bearing antenna structure(CLAS) for high speed military jet application. A log periodic patch type antenna was designed for multi-band communication and navigation antenna. Carbon/Glass fiber reinforced polymer was used as a structure supporting aerodynamic loads and honeycomb layer was used to improve antenna performance. Multi-layers were stacked and cured in a hot temperature oven. Gain, VSWR and polarization pattern of CLAS were measured using anechoic chamber within 0.15~2.0 GHz frequency range. Tension, shear, fatigue and impact load test were performed to evaluate structural strength of CLAS. Antenna performance test after every structural strength test was conducted to check the effect of structural test to antenna performance. After the application of new test and evaluation procedure to validate a new CLAS, a design improvement was found.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.05a
• /
• pp.125-128
• /
• 2008

In this paper, a stand-type planar antenna of 900MHz RFID band is designed and fabricated. As the proposed antenna is stand-type use of air permittivity, Bandwidth used ground height at rectangle patch structure and coaxial feed line is widen. Also wideband width can solve problem that RFID tag attached to things happens frequency shift keying phenomenon by liquid, special metal, temperature, humidity etc. Bandwidth of fabricated antenna to VSWR less than 2 is satisfied 11.9% at $890MHz{\sim}1000MHz$. And proposed antenna is circular polarization antenna of operating characteristics that axial ratio is less than 2 and gain is 6dBi.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.13 no.5
• /
• pp.1-8
• /
• 1976

Microwave GaAs Metal Semiconductor Field effect Transistors (MESFET) with the gate-length of two micrometers are investigated. The scattering parameters of the transistors have been measured from 1GHz to 2GHz by Hp8545 Automatic network analyzer. From the measured data, an equivalent circuit is established which consists of an ntrinsic and. extrinsic transistor elements. In this paper, GaAb MESFET Amplifier is used in conjunction with conventional microstrip techniques to match into a 50 ohms high input/output impedances system. We found that Power gain is less than 8dB and VSWR is less than 1.5 in L-Band.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.7 no.3
• /
• pp.56-61
• /
• 2008

Recently, although demands for an internal antenna applicable to DVB-H handhold terminals are increased, there are many difficulties in designing the antenna due to the long wavelength of $430{\sim}640mm$ and the wide bandwidth of $470MHz{\sim}702MHz$. Since the proposed DVB-H band antenna can be analyzed as an SDA (Supported structure Defined Antenna), it is designed by combination of the folded monopole radiator which has a wideband characteristics and the wing-type element which can reduce the resonant frequency effectively. The DVB-H band antenna has VSWR of 4 and obtains a good gain from -5 to 2 dBi, when it is built-in the mobile handset.