• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 1998.11a
• /
• pp.47-52
• /
• 1998

최근에 세라믹-금속 접합, 열차폐코팅(Thermal Barrier Coating), 마모저항코팅등 이종재료접합의 이용이 급증하고 있다. 열차폐코팅의 경우, 고온환경쪽에 세라믹을 배치하여 내열성을 부여하고, 냉각환경쪽은 금속재료를 사용하여 열전도성과 기계적 강도를 부여한다. 이 때 두 재료의 경계부에서는 열적, 기계적 특성 차이로 인하여 제조과정이나 사용중에 열적, 기계적 부하에 의하여 내부잔류응력이 생기게 되며, 이는 재료의 강도, 파괴특성에 많은 영향을 미치기 때문에 잔류응력의 감소기술이 중요시되고 있다. (중략)

• Journal of the Korean Vacuum Society
• /
• v.1 no.1
• /
• pp.176-182
• /
• 1992

t-Stress and junction leakage current characteristics of CVD-tungsten have been investigated. Stressversus continuous annealing temperature plot. shows hysteresis curve where the stress level of the cooling curveis higher than that of the heating curve. It is found that the thermal and intrinsic stress of tungsten film depositedby SiH4 reduction is higher than that by Hz reduction.The tungsten film deposited by SiHl reduction is in the tensile stress state below 700"Cnd the stress ofthe film decreses with increasing annealing temperature. The stress state changes into compressive stress atabout 700"Cnd the compressive stress increases rapidly with increasing temperature.Leakage current of the n+/p diode increases rapidly especially in the range of 400-450$^{\circ}$C with increasingdeposition temperature of the CVD-W by SiH4 reduction, which is due to the Si consumption by W encroachment.On the other hand leakage current of the n+/p diode slightly increases with increasing SiH4/WF6 ratio.h increasing SiH4/WF6 ratio.

• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.71-72
• /
• 2004

솔더접합부의 신뢰성을 평가하기위해서는 접합부에 대한 기본적인 기계적 특성 평가 및 온도, 수분, 진동, 응력 및 전압 둥 각종 환경하에서의 접합부에 대한 장단기 신뢰성시험이 요구된다. (중략)

• Journal of Korean Society of Steel Construction
• /
• v.30 no.2
• /
• pp.115-126
• /
• 2018

Internationally representative steel design standards have forbidden or limited the application of high-strength steels to tubular joints, partly because of concerns about their unique material characteristics such as high yield ratio. Most of design standards stipulate that for steels whose yield strengths exceed 355 or 360 MPa, the strength equations cannot be utilized or strength reduction factor below 1.0 should be multiplied. However, the mechanical background behind these limitations is not clear. Experimental testing of high-strength steel CHS (circular hollow section) X-joints recently conducted by the authors also clearly indicated that the current limitations might be unduly conservative. As a continuing work, extensive, test-validated numerical analyses were made to investigate the behavior of high-strength steel CHS X-joint under axial compression. Three steel grades covering ordinary to very high strength steels were considered in the analysis. Again it was found that the high strength penalty to the joint strength in current standards is too severe and needs to be relaxed. The high-strength steel joints under the effects of chord stress generally showed higher strength than the ordinary steel joints and their strengths were conservatively predicted by current standards. It is also emphasized that current format of the CHS X-joint strength equation does not reflect observed behavior and needs to be recast.

• Proceedings of the KWS Conference
• /
• 1999.05a
• /
• pp.237-240
• /
• 1999

In this study, residual stresses of the weldment were calculated by finite element analysis(FEA) and experiment. And, the crack closure behaviour and fatigue crack growth characteristics in field of residual stress of A106 Gr B steel pipe weldment were investigated under various stress ratio. Obtained results are as follows. I) $K_{op}$ was independent of $K_{max}$, and load ratio in fatigue crack growth. 2) In variation of load ratio, the scatter band of crack growth curve was reduced by half considering crack closure. and 3) Neglecting crack closure behaviour, actual fatigue crack growth rate can be underestimated' and Actual fatigue crack growth rate can be overestimated by $K_{res}$, in tensile residual stress field.

• Proceedings of the KWS Conference
• /
• 2000.10a
• /
• pp.87-89
• /
• 2000

• Proceedings of the KWS Conference
• /
• 2000.10a
• /
• pp.102-105
• /
• 2000

• Proceedings of the KWS Conference
• /
• 2003.05a
• /
• pp.219-221
• /
• 2003

• Journal of Korean Society of Steel Construction
• /
• v.16 no.5 s.72
• /
• pp.505-517
• /
• 2004

This paper presented equations on the stress evaluation of steel frame pier connections that were composed of a box beam and a circular column. The existing equations, which transformed the circular column into an equivalent box column had some problems; they underestimated a shear lag stress as the joint angle decreased, and overestimated a shear stress as the joint angel increased. Therefore, FE analyses were performed with various parameters, such as joint angle(${\alpha}$), span length-width ratio(L/B), and circular column-to-box beam stiffness ratio(${\alpha}$), and new equations on stress evaluation were proposed based on FE analyses. Furthermore, material and geometric nonlinear analyses were performed to estimate ultimate strength and to confirm the validity of the proposed equations.

• Journal of Welding and Joining
• /
• v.5 no.2
• /
• pp.1-8
• /
• 1987

MSR 처리를 실제구조물에 적용하기 위해서 잔류응력과 기계적성질에 대하여 조사해 본 결과 다음의 결론을 얻었다. (1) MSR 처리는 소성변형을 유발시켜 높은 인장잔류응력을 감소시키는데 유효하며, 잔류응력이 낮은 부위에 대해서는 잔류응력 재배치에 따른 응력치의 변화가 수반된다. (2) 잔류응력 감소량은 MSR 하중에 비례하여 증가 한다. (3) 모재의 항복응력보다 낮은 하중으로 MSR 처리를 하면 충격치의 감소는 무시할 정도이지만 모재의 항복응력보다 높은 하중으로 행하면 응착금속에서 충격치의 감소가 현저하다. (4) MSR 처리를 하게되면 항복응력이 높아지고, 잔류응력이 감소해서 선형의 응력-스트레인의 관계를 가지는 범위가 넓어져서 구조적으로 안전한 상태가 된다.