• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.345-352
• /
• 2013

In this research, a study on stress shape functions was conducted to analyze the contact stress problem by using a hybrid photoelasticity. Because the contact stress problem is generally solved as a half-plane problem, the relationship between two analytical stress functions, which are compositions of the Airy stress function, was similar to one of the crack problem. However, this relationship in itself could not be used to solve the contact stress problem (especially one with singular points). Therefore, to analyze the contact stress problem more correctly, stress shape functions based on the condition of two contact end points had to be considered in the form of these two analytical stress functions. The four types of stress shape functions were related to the stress singularities at the two contact end points. Among them, the primary two types used for the analysis of an O-ring were selected, and their validities were verified in this work.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.117-117
• /
• 2004

일반적으로 접촉 피로 마멸은 구름 또는 미끄럼 접촉시 작용하는 반복 응력에 의해 표면과 표면 아래에 균열이 형성되고 성장 및 합체의 과정을 거쳐 표면의 일부가 떨어져 나가는 손상으로 기어나 캠-롤러, 구름 베어링과 같이 구름-미끄럼 접촉상태로 운전하는 기계요소에서 가장 중요하게 고려되어야 할 파손 메커니즘이다. 특히 기어나 구름 베어링 같이 고주기 접촉 피로 특성을 지니는 기계요소의 수명은 피로수명 실험과 통계적 기법을 이용한 Weibull 이론을 기초로 한 수명식을 대부분 사용하고 있다.(중략)

• Journal of the Korean Institute of Gas
• /
• v.15 no.6
• /
• pp.34-37
• /
• 2011

This paper presents sealing contact stress and deformation behaviors of an elastomeric contact seal for a pipe connection. In this study, a pipe connection is used by a joint nut and an elastomeric contact seal with a sealing interference of 0.2~0.5mm. A sealing interference in which compresses an elastomeric contact seal is generated by fastening a joint nut between two pipes. The FEM computed results show that the contact normal stress of contact model 1 with an inclined sealing surface is 1.5~1.75 times high in compared with that of contact model 2 with a parallel sealing surface. This indicates that the sealing contact surface recommends a wedge contact mode between two pipe connections for a high sealing compression stress.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.6
• /
• pp.583-588
• /
• 2015

Asymptotic method has been often used to theoretically analyze the complete contact problem. The error of the asymptotic results increases as the distance from the contact edge increases. The singularity cannot be properly obtained from a finite element (FE) analysis owing to the finiteness of the element size. In the present work, the complete contact problem in bonded condition is analyzed using a combined experimental-numerical approach to assist and/or compare with the asymptotic results. Al and Cu alloys are used for the material combination of the punch and substrate. 120 and 135 degrees are used for the punch angle. The FE models are validated by comparison of displacement distributions obtained by the FE analysis and $moir{\acute{e}}$ experiment. Generalized stress intensity factors are evaluated using the validated FE models. Stress field in the vicinity of the sharp contact edges obtained from the FE and asymptotic analyses are compared. The discrepancies are also discussed.

• Journal of the Korean Society for Railway
• /
• v.10 no.5
• /
• pp.546-553
• /
• 2007

The objective of the present paper is to evaluate the effect of the evolution of contact surface profile by fretting wear on the contact stress distribution and fatigue crack initiation site of press-fitted shaft by means of an analytical method based on experimental data. A finite element analysis was performed to analyze the stress states of press-fitted shaft, considering the worn contact surface profiles of shaft. The evolutions of contact stress as wearing of contact surface were analyzed by finite element analysis and fatigue crack nucleation sites were evaluated by fretting fatigue damage parameter (FFDP) md multiaxial fatigue criteria. It is found that the stress concentration of a contact edge in press-fitted sha손 decreases rapidly at the initial stage of total fatigue life, and its location shifts from the contact edge to the inside due to fretting wear as increasing of fatigue cycles. Thus the transition of crack nucleation position in press-fitted shaft is mainly caused by stress change of a contact edge due to the evolution of contact surface profile by fretting wear. Therefore, it is suggested that the nucleation of multiple cracks on fretted surface of press fits is strongly related to the evolution of surface profile at the initial stage of total fatigue life.

• Korean Journal of Materials Research
• /
• v.3 no.1
• /
• pp.58-64
• /
• 1993

The degree of work hardening in the subsurface zones varied with the experimental conditions under the rolling contact fatigue wear test of high carbon Cr-Ti alloy steel was evaluated by the distribution of residual stresses. Surface residual stresses before the test did not affect the wear property. Surface residual stresses after the test decreased by the increase of contact stress and running. velocity. but the maximum compressive residual stress and its depth of saturation in the subsurface zone increased. The relationship between these experimental results and the distribution of the theoritical shear stress was also discussed.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.06a
• /
• pp.61-66
• /
• 1999

반복 응력 상태 아래서 알루미나 세라믹의 피로 표면손상 누적현상이 분석되었다. 연속 미끄럼 접촉 시에 발생하는 응력 상태를 재현하기 위해서 동시에 작용하는 수직-수평 반복 압축하중 기법이 사용되었다. 알루미나 구와 평판의 접촉면에서 알루미나 미세 결정의 피로 파손에 의한 마모 입자 형성 기구가 관찰되었고, 반복하중의 횟수와 수직-수평 하중비가 커질수록 마모량은 증가하였다. 반복 접촉하중에 의한 표면손상 누적이 접촉 수직 변위 측정으로 정량화 되었다. 두 접촉 구조물의 강성 (하중-변위 선도의 기울기) 변화가 두 재질의 탄성계수의 변화로 표현되었다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.2 no.3
• /
• pp.69-77
• /
• 1978

스폿 용접 기구를 탄성체로 생각하여 접촉 응력과 용접봉의 최적 형상을 구하였다. 접촉 응력은 2차 계획법 문제로 바꾸어 해석하였고, 이에 필요한 용접봉과 피용접판의 Flexibility matrix 들은 유한 요소법의 프로그램인 SAPIV 를 사용하였다. 최애 접촉 응력을 최소로 하는 용접봉의 형상설계를 위해 축차적인 선형 계획법을 적용하고 특정한 경우의 해를 도시하였다. 최적의 용접봉 모양은 중심부가 오목하고 가장자리 부분이 볼록한 형태로 나타났다.

• Computational Structural Engineering
• /
• v.6 no.3
• /
• pp.89-97
• /
• 1993

General formulation to analyse the rectangular thin plate on a soil medium by energy method is developed. In the problem, Boussinesque's formular needs to be integrated after assuming the contact stress distribution. Two different functions, i.e., power series and Chebychev polynomials are used to approximate the contact stress distribution. It was found that Chebychev polynomials are better function to describe the contact stress than power series. Chebychev polynomials considering stress singularity around plate boundary is recommended as the desirable shape function for future research.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.5
• /
• pp.633-644
• /
• 2008

The structural framework design uses high-strength bolts and welding in column splices. However, for the column under high compression, the number of the required high-strength bolts can be excessive and the increase of welding results in difficulty of quality inspection, the transformation of the structural steels, and the increase of erection time. According to the AISC criteria, when columns have bearing plates, or they are finished to bear at splices, there shall be sufficient connections to hold all parts securely in place. The Korean standard sets the maximum 25% of the load as criteria. Using direct contact makes it possible to transfer all compressive force through it. The objective of this study is to examine the generally applied stress path mechanism of welded or bolted columns and to verify the bending moment and compression transfer mechanism of the column splice according to metal touch precision. For this study,22 specimens of various geometric shapes were constructed according to the change in the variables for each column splice type, which includes the splice method, gap width, gap axis, presence or absence of splice material, and connector type. The results show that the application of each splice can be improved through the examination of the stress path mechanism upon metal contact. Moreover, the revision of the relative local code on direct contact needs to be reviewed properly for the economics and efficiency of the splices.