• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.7
• /
• pp.723-730
• /
• 2012

During the cold wire-drawing process, the diameter of a wire is reduced and the length of the wire is increased as the wire passes through the die. The pressure and sliding motion at the interface between the wire and die cause elastic recovery of the workpiece and friction and wear on the die. In addition, wire deformation and frictional heating raise the temperature of the wire and die, resulting in difficulty in manufacturing the drawn products according to a designated inner diameter of the die, deviating from the designated dimension or the inner diameter of the die. In this study, considering the die temperature distribution, the effects of dimensional changes of the drawn products were analyzed quantitatively; these changes are caused by the elastic deformation of the die, the elastic recovery of the workpiece, and the thermal deformation of both the die and the workpiece. It was confirmed that the elastic recovery of the workpiece influenced these changes the most. The initial dies considering these factors could avoid deviation from the designated dimension, and the desired drawn products were obtained by using the designed initial drawing dies.

• Journal of Life Science
• /
• v.15 no.1 s.68
• /
• pp.112-117
• /
• 2005

Plants living riverside show diverse resistance responses to submergence. The promoted petiole elongation of semi-aquaitc plants, e.g., such as Ranunculus sceleratus and Rumex palustris, is one of the adaptive responses mediated by the plant hormone ethylene. The gaseous hormone is trapped in submerged plant tissues and enhances the petiole growth by increasing sensitivity of the tissues to some plant hormones including auxin. Due to the stimulated growth of petioles, the leaves finally reach the water surface and can respirate again. At the water surface, the accumulated ethylene diffuses out from the tissues to the air. As a result, the increased hormone sensitivity decreases again, and thus the growth rate reduces to the basal level as before. The increased auxin sensitivities by ethylene observed in Ranunculus sceleratus, revealed by the changes in the auxin dose-response curves, indicate the increase of affinities of the receptors to auxin. However, the molecular mechanism of the affinity regulation remains still largely unknown, because the identity of the auxin receptor is still unclear.

• Journal of the Society of Naval Architects of Korea
• /
• v.38 no.1
• /
• pp.72-85
• /
• 2001

A study for the structural strength evaluation on the doubler plate subjected to the biaxial in-plane compression has been performed through the systematic evaluation process. In order to estimate the proper static strength of doubler plate, elasto-plastic large deflection analysis is introduced including the contact effect between main plate and doubler. The characteristics of stiffness and strength variation are discussed based on their results. A1so, in order to compare the doubler structure with the original strength of main plate without doubler, a simple formula for the evaluation of the equivalent flat plate thickness is derived based on the additional series analysis of flat plate structure. Using this derived equation, the thickness change of a equivalent flat plate is analyzed according to the variation of various design parameters of doubler plate and some design guides are suggested in order to maintain the original strength of main plate without doubler reinforcement. Finally, correlation between derived equivalent flat plate formula and the developed buckling strength formulas by author et a1. is discovered and these relations are formulated for the future development of simple strength evaluation formula of doubler plate structure.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.26 no.1
• /
• pp.130-136
• /
• 1997

Total parenteral nutritional effect was induced by surgical creation of Thiry-Vella fistula(TVFs) in rats. Glutamine, glycine or nucleosides/nucleotide mixture in solution was injected into the loops for 2, 4, 6, 8 days. Control animals received a 0.9％ saline solution. Results include weight gain, total protein, DNA, ［$^3$H］ thymidine incorporation into DNA, morphometry of the intestine in both TVFs and intestine in continuity. Perfusion of nucleosides/nucleotide mixture into the bypassed loops caused an increase in total protein, DNA content, villous height, villous surface area in loops. The injection of glycine into loops caused an increase in ［$^3$H］ thymidine incorporation but the mean values of the protein and DNA contents were not significantly different from those in group Cont and group Nuc. Overall values for group Gln were slightly higher than those of the control but the differences were not statistically significant. This study suggests that this animal model may be useful for studying the effect of dietary factors on intestinal growth and maturation, separating the direct effect of diet from systemic effect on the intestine.

• Radiation Oncology Journal
• /
• v.8 no.1
• /
• pp.133-136
• /
• 1990

Intracavitary brachytherapy combined hypertermin for utero-conical cancer seems to be a promising method for salvage treatments in persistent tumors and inoperable or previously irradiated cervical recurrences. In order to heat the vaginal apex and uterus, powerfull conical antennas which are suitable for afterloading cervical applicator have been designed for use in conjuction with intracavitary radiation therapy. The antennas were constructed with conical conductive material to feed line and the effective lenght were designed proportional to microwave length, Power deposition profiles of 2450 MHz of conical antennas were studied in both phantom models and muscle tissue and compared to those of commonly used dipole antenna. Improvement of the heating pattern was found in both phantom and muscle tissue. The heating pattern produced by the conical antenna resembles an ellipsoid and then the temperature distribution in depth was extended to $2\~3\;cm$ from the effective antenna axis.

• Journal of the Korean Vacuum Society
• /
• v.17 no.2
• /
• pp.109-112
• /
• 2008

The miniaturization of device size and submicron process causes serious problems in conventional metallization due to the solubility of silicon and metal at the interface, such as an increasing contact resistance in the contact hole and interdiffusion between metal and silicon. Moreover, the interaction between Cu and Si is so strong and detrimental to the electrical performance of Si even at temperatures below $200^{\circ}C$. Therefore it is necessary to implement a barrier layer between Cu and Si. So we study W-C-N diffusion barrier for prevent Cu diffusion as a function of $N_2$ gas flow and thermal stability. Especially, we also study the W-C-N diffusion barrier for analyzing the change of lattice constants.

• Journal of Biomedical Engineering Research
• /
• v.23 no.1
• /
• pp.27-32
• /
• 2002

The purpose of this study was to evacuate the effects of the number of tied hollow fibers in a novel membrane oxygenator that satisfied the limiting factor of minimizing the friction loss in the intravascular blood flow Pattern. The membrane oxygenator is a bundle consisted of several hundred ho1low fibers haying the outside diameter of 380 $\mu m$ and the axial jacket length of 600 mm. The eight different variation of tied hollow fibers in a bundle were designed. and the liquid flow pattern was controlled by a pump. The liquid pressure drop was measured by in vitro experiments using water and g1ycero1. Uniform blood flow pattern was observed for each number of tied hollow fibers. Pressure drop was 13-16 mmHg outside of the membrane oxygenator consisting of up to 700 ho1low fibers. More effective contact of liquid with the tied ho1low fibers was observed as a decrease in the number of the tied hollow fibers. and resulted in the enhancement of the friction tractor

• Journal of the Korean Society for Railway
• /
• v.15 no.5
• /
• pp.429-435
• /
• 2012

The HEMU-430X is a world-class railway vehicle which aimed the maximum speed of 430km/h and the operation speed of 370km/h. To maintain high-speed operation condition over 300km/h, various requirements for satisfy exist. However, one of the most important things is a reliable supply of electricity. Especially, the dynamic interaction between the pantograph and overhead contact line at high-speed is a significant matter to pre-evaluate. In this paper, using the dynamic interaction analysis program, current collection performance of the HEMU-430X was investigated. Firstly, based on the international standard, performance of the original specifications was evaluated. In addition, through study on changes in tension and span length, improvement of the performance was considered.

• Clean Technology
• /
• v.18 no.3
• /
• pp.312-319
• /
• 2012

Malachite green is used a dye but malachite green is harmful toxic substance. In this study, the adsorption characteristics of zeolite has been investigated for the adsorption of malachite green dissolved in water. The effects of initial dye concentration, contact time, pH and temperature on adsorption of malachite green by a fixed amount of zeolite have been studied in batch adsorber and fixed bed. The adsorption equilibrium data are successfully fitted to the Freundlich isotherm equation in the temperature range from 25 to $45^{\circ}C$. The estimated values of k and ${\beta}$ are 23.60-46.88, 0.225-0.347, respectively. The mechanism of the adsorption process was determined from the intraparticle diffusion model. The effects of the operation conditions of the fixed bed on the breakthrough curve were investigated. When the inlet concentration and initial flow rate of malachite green are increased, the corresponding adsorption breaktime appears to decrease. Breaktime increased with increasing bed height and length of adsorption zone showed similar patterns.

• The Journal of the Acoustical Society of Korea
• /
• v.39 no.5
• /
• pp.435-440
• /
• 2020

Single-beam acoustic tweezers that are capable of manipulating micron-size particles in a non-contact manner have been used in many biological and biomedical applications. Current single-beam acoustic tweezer systems developed for in vitro experiments consist of a function generator and a power amplifier, thus the system is bulky and expensive. This configuration would not be suitable for in vivo and clinical applications. Thus, in this paper, we present a portable single-beam acoustic tweezer system and its performances of trapping and manipulating micron-size objects. The developed system consists of an Field Programmable Gate Array (FPGA) chip and two pulsers, and parameters such as center frequency and pulse duration were controlled by a Personal Computer (PC) via a USB (Universal Serial Bus) interface in real-time. It was shown that the system was capable of generating the transmitting pulse up to 20 MHz, and producing sufficient intensity to trap microparticles and cells. The performance of the system was evaluated by trapping and manipulating 40 ㎛ and 90 ㎛ in diameter polystyrene particles.