• Journal of the Korean Geosynthetics Society
• /
• v.5 no.4
• /
• pp.27-33
• /
• 2006

Frictional properties between geostrip and sand paper interface were estimated considering soil particle size also the friction coefficients and angles were determined with normal stress. Three kinds of geostrips of design strength 50, 70, 100 KN/m were used and 5 sandpapers of P100, P220, P320, P400, P600 were used also. Shear strength between geostrip and sand paper interface with design strength showed big difference and this is due to the uniform surface pattern of each geostrip when contact to sandpaper without regard to design strength. Shear strength of geostrip was increased with design strength and geostrips/P100 sandpaper interface showed the biggest value. Finally, all of geostrips showed the decrease phenomena of post-peak strength and this is due to the abrasion of geostrip surface by shear test.

• Applied Chemistry for Engineering
• /
• v.21 no.4
• /
• pp.457-462
• /
• 2010

In this research, the effects of the concrete superplastizers on the wettability of cement particle and concrete strength were studied. The wettability of the cement particles strongly depended on the type of the superplastizer. When the superplastizer had a higher wettability with the cement particles, it revealed a good fluidity of the concrete mortar and a higher concrete strength. Non-ionic superplastizers (polycarboxylic type) had a relatively good performance on the mortar fluidity and concrete strength properties compared to anionic superplastizers (lignosulfate, sulfonated naphthalene formaldehyde, sulfonated melamin formaldehyde). It was observed that the blending of the polycarboxylic and the lignosulfate type concrete superplastizers resulted in synergistic effects on the concrete mortar fluidity and concrete strength properties.

• Elastomers and Composites
• /
• v.46 no.2
• /
• pp.125-131
• /
• 2011

The effects of chopped kenaf fiber concentration on mechanical property of polypropylene (PP) composite are investigated. The addition of kenaf increased the tensile strength, flexural modulus, impact strength, specific gravity, and HDT, while decreased the elongation%, flexural strength, and melt flow index. The increase of mechanical properties is due to increased surface area contacting between fiber and polymer matrix and fiber-fiber interaction. Volatile extractives in the kenaf seemed to decrease the interfacial adhesion between kenaf surface and PP.

• Journal of the Korean Ceramic Society
• /
• v.40 no.7
• /
• pp.662-666
• /
• 2003

Hertzian cyclic fatigue properties of the alumina-glass dental ceramics were evaluated in exact in vitro environment at contact loads from 200 N to 1000 N and up to 10$\^$6/ cycles to investigate the indentation damage and strength degradation. At 200 N, no strength degradation and crack generation was observed up to 10$\^$6/ contact cycles. As load increased from 200 N to 1000 N, the drastic reduction in strength was found when the damage transition from ring to radial crack occurred. The extent of strength degradation was more pronounced in vitro environments probably due to chemical reaction of artificial saliva with glass phase through radial cracks introduced during large numbers of contacts.

• Composites Research
• /
• v.23 no.5
• /
• pp.1-7
• /
• 2010

To increase the adhesive strength of acrylonitrile butadiene rubber(NBR) and steel plate, the atmospheric pressure flame plasma(APFP) treatment device is applied. The effect of various conditions(processing velocity and distance) is experimentally investigated to ascertain the optimum conditions to yield the best adhesive properties. It is found that the optimum distance between burner port and steel plate is 40mm and the optimum processing velocity is 50m/min at given condition. When the surface is coated twice with the bonding agent, the adhesion strength of APFP treated steel plate is increased to about 20.5%. It suggests that the surface modification of steel by flame plasma treatment at atmospheric pressure is a proper and applicable method to improve the adhesion strength between steel and rubber.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.2
• /
• pp.133-140
• /
• 2018

A nonlinear finite element analysis was conducted in order to examine the moment capacity and flexural behaviour of hollow prestressed concrete filled steel tube(HCFT) piles which compose hollow PHC piles inside thin wall steel tubes. The parameters investigated in this study were various contact conditions between concrete and steel tube, thickness of concrete tube and various PC strands. A simple method is proposed to determine the ultimate flexural strength based on plastic stress distribution method. In order to verify the proposed method, calculated moment capacity of various HCFT piles are compared with the experiment and numerical analysis results.

• Composites Research
• /
• v.16 no.4
• /
• pp.10-21
• /
• 2003

Proposed is a new method to determine the characteristic lengths for the failure analysis of composite joint without experiments. New method uses the result that the stress distribution in the characteristic length specimens is linearly proportional to the applied load. The compressive characteristic lengths calculated by the present method are exactly same as the lengths obtained by the conventional method based on experiment. The new tensile characteristic length is defined using the strength of the notched laminate, while previous methods use the strength of the sound laminate. That change allows calculating the tensile characteristic length numerically without experiment like the compressive characteristic length. Finite element analyses are conducted by MSC/NASTRAN. The interface between the fastener and laminate is modeled by the contact surface element. The finite element results based on the new characteristic lengths show the excellent agreement with experimental results for the Graphite/Epoxy composite .joints.

• Polymer(Korea)
• /
• v.29 no.2
• /
• pp.166-171
• /
• 2005

EPDM (ethylene propylene diene monomer)/silicone rubber blends were prepared and the influence of a compatibilizer and thermal aging on the properties of the blends was investigated. The blends of which the compositions were varied in the range of 90/10 through $10/90\;wt\%$ were melt mixed by using a Brabender Plasticoder (internal mixer) and were vulcanized by a hot press. The morphology of the vulcanized EPDM/SR blends was examined by scanning electron microscopy (SEM). After the thermal Aging for 24, 48, 96 hrs at $100^{\circ}C$ in an air oven, hardness, tensile strength, elongation and contact angle of the blends were investigated. From the result of the morphology, it was confirmed that the domain size of the blends containing the compatibilizer was reduced. As the increase of the thermal aging time, hardness and tensile strength of the blends decreased but elongation and contact angle increased.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.2 no.2
• /
• pp.135-143
• /
• 2004

An experimental study on the sorption of U(VI) onto a Korean granite was performed as a function of the geochemical parameters such as contact time, pH, ionic strength, and carbonate concentration using a batch procedure. The distribution coefficient,$K_d$, was about 1-200 mL/g depending on the experimental conditions. The sorption of U(VI) onto granite particles was greatly dependent upon the contact time, pH, and carbonate concentration, but insignificantly dependent on the ionic strength. It was noticed that the sorption of U(VI) onto granite particles was highly correlated with the uranium speciation in the solution, which was dependent on the pH and carbonate concentrations. It was deduced from the kinetic sorption experiment that a two-step first-order kinetic behavior could dominate the kinetic sorption of U(VI) onto granite particles. In the alkaline range of a pH above 7, U(VI) sorption was greatly decreased and this might be due to the formation of anionic U(VI)-carbonate aqueous complexes as predicted by the speciation calculations.

• Composites Research
• /
• v.29 no.5
• /
• pp.262-268
• /
• 2016

In this work, the pitch-based carbon paper (P-CP) was prepared by re-impregnating of binder pitches and PAN-based milled carbon fibers (MCF) at low temperature carbonization process. The influence of MCF content on physicochemical properties of MCF/P-CP was investigated. As a result, the tensile strength of MCF/P-CP was increased sharply from 10 wt.% to 20 wt.% of MCF. Also, the increase of MCF content led to the decrease of interfacial contact resistivity and the improvement of electrical and thermal conductivity of MCF/P-CP. These results were probably due to the increase of density of MCF/P-CP, resulting in the formation of electrically and thermally conductive paths of the carbon paper.