• The korean journal of orthodontics
• /
• v.27 no.5 s.64
• /
• pp.839-852
• /
• 1997

It has been submitted that different ion solutions containing sulfate induce crystal growth and might substitute conventional acid etching for pretreatment of enamel in orthodontic bonding(${\AA}rtun$ et al., Am. J. Orthod. 85, 333, 1984). This investigation was designed to evaluate the relevance of crystal growth on the enamel surface as an alternative to conventional acid etching in direct bonding of orthodontic brackets. Annexing Li2SO4, MgSO4, K2SO4 respectively in the solution with $25\%$ polyacrylic md 0.3M sulfuric acids were employed to enhance the crystal growth. Human bicuspids were treated with various parameters as combinations of crystal growth and glass ionomer cement, crystal growth and orthodontic resin, acid etching and orthodontic resin for an investigative purpose. Crystal growth solution containing MgSO4 showed the highest shear bond strength(15.6MPa) within the groups of bonding brackets with glass ionomer cement(p<0.01). Bonding with glass ionomer cement on the surface of crystal growth demonstrated higher shear bond strength than with orthodontic resin(p<0.001). Bonding with glass ionomer cement on the surface treated with crystal growth solution containing MgSO4 or K2SO4 was not different shear bond strength statistically from bonding with orthodontic resin on the acid-etched surface. It suggests that bonding brackets with glass ionomer cement on the surface treated with crystal growth solution containing MgSO4 or K2SO4 is a potential alternative to bonding with resin on the acid etched sufrace.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.44 no.4
• /
• pp.412-418
• /
• 2017

During orthodontic treatment, formation of white spot lesions (WSLs) around brackets has long been recognized as a potential risk. This study performed to investigate effect of preventing enamel demineralization and remineralization by application of fluoride-containing orthodontic primer. Fifty extracted bovine incisors teeth were randomly allocated to 3 groups: (I) Non-preparation specimens, (II) Application of Light Bond$^{TM}$ as fluoride containing orthodontic primer, (III) Application of Transbond$^{TM}$ XT Primer as traditional orthodontic primer without fluoride. Each group is demineralized under artificial carious solution. The demineralization pattern was evaluated using a Q-ray view, Vickers hardness test and polarized light microscope. The remained primer was calculated as 35 - 50%. The highest surface microhardness was shown on Light Bond$^{TM}$ surface. There were statistically significant differences in Vickers microhardness number between adjacent areas of Light Bond$^{TM}$ and non-prepared area. There was almost no demineralization of the enamel surface under the Light Bond$^{TM}$. At the adjacent site of Light Bond$^{TM}$, the shallow caries pattern and remineralization appearance were also observed. These results suggest that the use of fluoride-containing primers may be useful for bracket attachment to reduce enamel demineralization during orthodontic treatment.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.44 no.1
• /
• pp.1-10
• /
• 2017

The present study aimed to evaluate the validity of resin infiltration in improving color stability after tooth whitening. Enamel samples were extracted from 40 healthy bovine upper incisors, and primary staining and whitening were performed. After that, specimens were randomly divided into 3 groups : resin infiltration group (n = 15, RI group), resin adhesive group (n = 15, RA group), and control group (n = 10). Secondary staining was performed on all samples. Coloration was assessed 5 times as follows: initial color, immediately after staining, after whitening, after resin application, and after secondary staining. Color was measured using a spectrophotometer and recorded by using the CIE $L^*a^*b^*$ color space. The color changes after primary staining for the RI, RA, and control groups were $12.16{\pm}3.50$, $12.16{\pm}3.38$, and $15.81{\pm}6.39$, whereas those after secondary staining were $15.21{\pm}7.19$, $15.93{\pm}4.31$, and $26.62{\pm}17.89$. Color changes after secondary staining showed a significant difference between the RI and control groups. In the within-group comparison between primary and secondary staining, there was no significant difference found in the RI group only (p = 0.26). The results suggest that Color stability after tooth whitening can be improved using resin infiltration.

• Journal of Welding and Joining
• /
• v.24 no.2
• /
• pp.10-16
• /
• 2006

본 논문에서는 전자 패키징의 고밀도 실장 프로세스와 관련하여 많은 연구와 개발이 이루어지고 있는 무연 솔더의 양산적용시의 문제점 침 도전성 접착제 및 3차원 패키징 기술과 신뢰성 평가방법 등을 개략적으로 소개하였다. 현재 국제적 규약에 의한 무연 솔더의 사용이 의무화되어 가고, 이에 따라 기존 솔더의 전기적 접속성, 열 도전성, 접합성 등의 특성을 확보하기 위한 새로운 재료 및 공정에 대한 연구 및 개발이 필요한 시점이다. 또한 기존의 접합 방법에서의 고집적화 및 미세 피치의 한계를 넘기 위한 3차원 패키징 기술 등이 시도되고 있다. 따라서 신소재 개발 및 공정 변화에 맞는 새로운 신뢰성 평가 방법의 도출도 필요하다. 아울러 국내 대학 및 관련 연구소에서도 국제 경쟁력을 향상시키고 차세대 첨단 산업 분야의 신기술을 확보하고 이를 선도하기 위한 체계적인 연구 활동이 요구된다.

• Restorative Dentistry and Endodontics
• /
• v.34 no.1
• /
• pp.51-60
• /
• 2009

The purpose of this study was to perform quantitative comparisons of water permeable zones in both the adhesive and the hybrid layer before and after thermo cycling in order to assess the integrity of the bonding interface. Twenty eight flat dentin surfaces were bonded with a light-cured composite resin using one of four commercial adhesives [OptiBond FL (OP), AdheSE (AD), Clearfil SE Bond (CL). and Xeno III (XE)]. These were sectioned into halves and subsequently cut to yield 2-mm thick specimens; one specimen for control and the other subjected to thermocycling for 10,000 cycles. After specimens were immersed in ammoniacal silver nitrate for 24 h and exposed to a photo developing solution for 8 h, the bonded interface was analyzed by scanning electron microscopy (SEM) and wavelength dispersive spectrometry (WDS) at five locations per specimen. Immediately after bonding. the adhesive layer of OP showed the lowest silver uptake, followed by CL, AD. and XE in ascending order (p < 0.0001); the hybrid layer of CL had the lowest silver content among the groups (p = 0.0039). After thermocycling, none of the adhesives manifested a significant increase of silver in either the adhesive or the hybrid layer. SEM demonstrated the characteristic silver penetrated patterns within the interface. It was observed that integrity of bonding was well maintained in OP and CL throughout the thermocycling process. Adhesive-tooth interfaces are vulnerable to hydrolytic degradation and its permeability varies in different adhesive systems, which may be clinically related to the restoration longevity.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.4 s.33
• /
• pp.49-53
• /
• 2004

Polymeric materials are widely used in the electronic industry as a common dielectric material or adhesive. The polymeric layer coated on Si substrate can be subjected to thermal stresses due to difference in thermal expansion coefficients. The mismatch in thermal properties between the polymeric layer and the substrate results in significant residual stresses. In this study, the thermal deformation is measured by a curvature measurement method using laser scanning, and the elastic modulus is calculated by an analytic model.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.14 no.1
• /
• pp.79-91
• /
• 2012

A curved fiber reinforced polymer (FRP) panel is produced with a certain width depending on allowances of manufacturing processes and facilities. An targeted arch-shaped structure could be built by sequential connection of series of the FRP panels. The connection manner between the FRP panels could be given by chemical treatment, mechanical treatment and hybrid method. Among those, the connection between the panels by chemical treatment is commonly adopted. Therefore, For an optimized design of the connected part between FRP pannels, a number of direct shear tests have been undertaken in terms of a number of parameters: surface treatment conditions, bonding materials, etc.. As results, surface grinding condition by sand paper or surface treatment by sand blasting appear properly acceptable methods, and epoxy and acryl resins are shown to be effective bonding materials for the purpose in this study.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.62-62
• /
• 2010

PVC(Polyvinyl Chloride)와 HDPE(High-density Polyethlene) 하수도관은 수많은 고분자 재료 중에도 높은 기계적 강도를 가지며, 광범위하게 사용되고 있다. 하지만, PVC와 HDPE 하수관을 연결하기 위해 소모 접착제나 고무링 이용한 소켓 방법 이음 방법은 낮은 수밀성과 기계적 강도로 오 폐수의 누수가 발생되고, 이것이 흙에 스며들어 지하수, 하천 및 토양을 오염시키고 있다. 따라서, 대안으로 최근에는 열판을 이용한 맞대기 융착 용접을 PE 하수도 관에 제한적으로 적용하여 시공하고 있다. 그러나, PVC 하수관은 열을 가할 시 열에 의한 민감한 거동으로 인해 맞대기 융착 용접법이 적용되지 못하고 있는 실정이다. 따라서 본 연구에서는 하수도 관 중, 국내에서 가장 많이 사용되고 있는 내 충격 PVC 하수도관과 HDPE 이중 벽관의 DSC(Diffential Scanning Calorimeter), TGA(Thermogravimetric analyzer), TMA(Thermomechanical Analysis), DMA(Dynamic Mechanical Analysis) 분석으로 온도에 따른 열적 거동을 분석하여, 적절한 융착 온도 조건을 제시하였다. 또한 접합강도 향상을 위한 이음부 설계를 제안하여, 융착 용접 특성을 평가하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.1
• /
• pp.52-57
• /
• 2007

One of the hot issues in composite patching is to reduce the thermal residual stresses between composite patch and aluminum surface which occurs after bonding of composite patch. In this study, the edge crack patching is adopted for different curing cycles. For the analysis, three layer Mindlin plate elements are used, and Paris' law is adopted to predict the fatigue life of composite patch plate. The analysis results show a good agreement with the experimental fatigue life and this technique can be applied for the prediction of fatigue life of aircraft structures.

• The korean journal of orthodontics
• /
• v.39 no.4
• /
• pp.213-224
• /
• 2009

Objective: The aim of this study was to find out whether Er:YAG laser can aid in debonding ceramic brackets, and to see what kind of method will be the most appropriate for debonding. Methods: One hundred and ninety teeth, monocrystalline brackets ($MISO^{TM}$, HT, Ansan-Si, Korea), polycrystalline brackets ($Transcend^{TM}$ series 6000, 3M Untek, Monrovia, CA, USA) and the KEY Laser3 (KavoDental, Biberach, Germany) were used. Experimental groups were classified according to the type of ceramic brackets, and the amount of laser energy (0, 140, 300, 450, 600 mJ). After applying laser on the bracket at two points at 1 pulse each, the shear bond strength was measured. The effect of heat caused by laser was measured at the enamel beneath the bracket and pulp chamber. After measuring the shear bond strength, adhesive residue was evaluated and enamel surface was investigated using SEM. Results: All ceramic bracket groups showed a significant decrease in shear bond strength as the laser energy increased. The greatest average temperature change was $3.78^{\circ}C$ on the enamel beneath the bracket and $0.9^{\circ}C$ on the pulp chamber. Through SEM, crater shape holes caused by the laser was seen on the enamel and adhesive surfaces. Conclusions: If laser is applied on ceramic brackets for debonding, 300 - 450 mJ of laser energy will be safe and efficient for monocrystalline brackets ($MISO^{TM}$), and about 450 mJ for polycrystalline brackets ($Transcend^{TM}$ series 6000).