• The Journal of Engineering Geology
• /
• v.19 no.4
• /
• pp.517-528
• /
• 2009

Statistical analyses of cut-slope stability were performed over approximately 5.7 km section along the National road No. 25, which cross-cuts in NW-SE direction the Cheongwon and Boeun-Gun area, Chungbuk. A measure of slope-stability was established by using direct reinforcement and indirect protection methods in whole section. Orientations(dip/dip direction) of the slopes, foliations(bedding), cleavages and joints were measured in total of 30 slope sites. The results analyzed using stereographic projection indicate that major directions of the slopes come out predominantly in three directions: 1) $58^{\circ}/095^{\circ}$, 2) $60^{\circ}/296^{\circ}$ and 3) $59^{\circ}/212^{\circ}$. In analyses of dip direction and frequency of cut-slopes established by reinforcement and protection methods, slopes with dip direction of $80-120^{\circ}$ and $280-320^{\circ}$ mostly occur. However, slopes with dip direction of $0-80^{\circ}$(N and NW) and $120-160^{\circ}$(SE) are not distributed in the study area. Failure aspects were analyzed for three major directions of the slopes, respectively. The results of failure aspects analyzed indicate that slopes in the study area could generate various failures as the results of intersection and/or intersection combination among joints, foliations(bedding) and cleavages. However, possibility of failure in a slope of major direction No. 3 is statistically very low because of low frequency in total number of slopes with the direction and of formation of small scale-slopes geographically, although the slope might generate all aspects of failure-modes.

• Explosives and Blasting
• /
• v.34 no.3
• /
• pp.10-16
• /
• 2016

Recently, transition from open pit to underground mining in limestone mines is an increasing trend in Korea due to environmental issues such as noise, dust and vibrations caused by crushers and equipment. The severe damages in the surrounding rock mass of underground opening caused by explosive blasting may lead to rock fall hazards or casualties. It is well known that variables which mainly affect blast-induced rock falls in underground mining are: blast vibration level, joint orientation and distribution and shape of the cross sections of underground structures. In this study, UDEC program, which is a DEM code, is used to simulate blast vibration-induced rock fall in underground openings. Variation of joint space, joint angle and joint normal stiffness was considered to investigate the effect of joint characteristics on the blast vibration-induced rock fall in underground opening. Finally, jointed rock mass models considering blast-induced damage zone were examined to simulate the critical blast vibration value which may cause rock falls in underground opening.

• Tunnel and Underground Space
• /
• v.11 no.3
• /
• pp.270-278
• /
• 2001

Two numerical methods such as DEM and FDM were adopted to analysis of rock slope stability, of which dimensions are about 150 m(length), 58 m(height), 70°dip, in Halla limestone mine. For this rock slope stability analysis, strength reduction method was used to calculate the safety factor of slope through numerical method. To keep the rock slope safely, it is proposed to reduce the height of the rock slope from 58 m to 45 m and to reduce the angle of the slope from 70°to 55°, too.

• Tunnel and Underground Space
• /
• v.16 no.6 s.65
• /
• pp.451-466
• /
• 2006

Analysis of slope behavior concerning the structural characteristics of field rock mass can be processed by virtue of borehole information of joint orientation and position acquired from DOM drilled core. Anticipated sliding potential of pre-failed rock slope is analyzed and the regional slope instability is investigated by inspecting the hazardous joints and blocks the traces of which is projected on the cut-face. Cross section has been set at the center of rock slope and the traces of both joints and tetrahedral blocks, which potentially can induce the slope failure, are drawn to investigate the failure modes and the triggering mechanism. Automated monitoring system has been established to measure the slope movement and especially, inclinometer has been installed inside DOM borehole to analyze the slope movement by considering the internal rock structure. Algorithms for predicting the slope failure time have been reviewed and the significance of heavy rainfall on the slope behavior has been investigated.

• The Journal of Engineering Geology
• /
• v.17 no.3
• /
• pp.393-404
• /
• 2007

The purpose of this study is to capture the essentials in survey and evaluation scheme which are able to assess the hazard of a rock slope systematically. Statistical analysis are performed on slope instability parameters related to failure of the rock slope. As the slope instability parameters, twelve survey items are considered such as tension crack, surface deformation, deformation of retaining structures, volume of existing failures, angles between strike of discontinuity and strike of cut slope face, angles between dip of discontinuity and dip of cut slope face, discontinuity condition, cut slope angle, rainfall or ground water level, excavation condition, drainage condition, reinforcement. A total of 233 road cut slopes located in Gyeongnam were considered. The stability of the road cut slopes were evaluated by estimating the slope instability index(SII) and corresponding stability rank. 126 rock slopes were selected to analyze statistical relation between SII and slope instability parameters. The multiple regression analysis was applied to derive statistical models which are able to predict the SII and corresponding slope stability rank. Also, its applicability was explored to predict the slope failures using the variables of slope instability parameters. The results obtained in this study clearly show that the methodology given in this paper have strong capabilities to evaluate the failures of the road cut slope effectively.

• Tunnel and Underground Space
• /
• v.20 no.3
• /
• pp.225-232
• /
• 2010

In this study, a newly modified 3-dimensional strain-dependent hydraulic conductivity modification relation which incorporates the influences of normal deformation and shear dilation is suggested. Since rock mass is simulated as a orthogonally jointed medium, an anisotropic hydraulic conductivity field can be evaluated using that relation. The empirical relationship on the basis of GSI and disturbance factor has been used to estimate the value of a modulus reduction ratio (ratio of rock mass deformation modulus to rock matrix elastic modulus). Principal hydraulic conductivity directions is not generally coincident with the global coordinate due to the inclining of joint and the influence of joint inclination is evaluated under strain rotation. Result shows that change of hydraulic conductivity does decreases with the increase of GSI and disturbance factor has much effects on the hydraulic conductivity of rock mass getting GSI value above 50. It is found that the inclination of joint impacts on the variation of hydraulic conductivity.

• Journal of the Korean Geotechnical Society
• /
• v.40 no.3
• /
• pp.101-108
• /
• 2024

A system with the ability to recognize potential key blocks during tunnel construction by analyzing the rock face was developed in this study. This system predicts the formation of key blocks in advance and evaluates their safety factors. A laser scanner was used to collect a three-dimensional point cloud of the rock face, which was then utilized to model the excavation surface and derive the joint surfaces. Because joint surfaces have specific strikes and dip angles, the key blocks formed by these surfaces are deduced through iterative calculations, and the safety factor of each key block can be calculated accordingly. The model experiments confirmed the accuracy of the system's output in terms of the joint surface characteristics. By inputting the joint surface information, the calculated safety factors were compared with those from the existing commercial software, demonstrating stable calculation results within a 1% error margin.

• Tunnel and Underground Space
• /
• v.13 no.5
• /
• pp.331-343
• /
• 2003

Though the Grouting has been in use for a long time, it is still regarded as an technique rather than engineering. The study of ground improvement by grouting is rare especially in jointed rock mass. In this study, biaxial compression tests were performed in the jointed rock mass models with .ough surfBce joints assembled with blocks before and after grouting. The load-deformation curves of the jointed rock masses showed a non-linear relationship before grouting but showed a relatively linear deformaion behavior after grouting. Improvement ratio (deformation modulus after grouting/deformation modulus before grouting) decreased with increasing joint spacing and lateral stress. Improvement ratio decreased exponentially with increasing deformation modulus of the rock mass model before grouting. Three-dimensional FDM analysis was performed to a highway tunnel case using experimental data of grouted rock. The convergence of the tunnel predicted after grouting by the numerical modelling coincided with those attained from the field measurement.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.2
• /
• pp.43-52
• /
• 2014

This paper examined the effect of step-wise excavation depth on the earth pressure against an excavation wall in rock mass. Numerical parametric studies were conducted based on the Discrete Element Method (DEM) to carry out the problems in rock mass. Controlled parameters included step-wise excavation depth, rock types, and joint conditions (joint shear strength and joint inclination angle). The magnitude and distribution characteristics of the induced earth pressure in a jointed rock mass were investigated and compared with Peck's earth pressure for soil ground. The results showed that the earth pressure against an excavation wall in rock mass were highly affected by different rock and joint conditions, and the effect of step-wise excavation depth increased as a rock type is deteriorated more. In addition, it was found that the earth pressure against an excavation wall in rock mass might be considerably different from Peck's empirical earth pressure for soil ground.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.608-610
• /
• 2009

지열 분포에 관련된 지질구조의 특성을 파악하기 위하여 지온경사, 지열류량 자료와 인접한 선구조의 방향성에 대한 상관성 분석을 실시하였다. GIS를 이용하여 지열정보데이터베이스에서 발췌한 209개 지온경사 자료와 218개 지열류량 자료에 대하여 전국 광역단열도로부터 가장 인접한 선구조를 추출하고 10도 간격의 방향별 지온경사 및 지열류량 자료 빈도 및 평균값을 그래프에 도시하였다. 인접 선구조의 방향별 지온경사 평균은 $N30^{\circ}{\sim}40^{\circ}W$, $N10^{\circ}{\sim}20^{\circ}E$ 방향에서 $58.9^{\circ}C/km$, $54.9^{\circ}C/km$로 가장 높았고, 인접 선구조의 방향별 지열류량 평균은 $N80^{\circ}{\sim}90^{\circ}W$, $N50^{\circ}{\sim}60^{\circ}W$ 방향에서 98.71 $mW/m^2$, $98.70mW/m^2$로 가장 높았다. 각 선구조 상의 좌표들을 이용하여 지열류량 분포도에서 지열류량 값을 추출한 결과 $N10^{\circ}W{\sim}N40^{\circ}E$, $N60^{\circ}{\sim}70^{\circ}W$, $N50^{\circ}{\sim}60^{\circ}E$ 방향의 지열류량 높은 것으로 나타났다. 결과적으로 지온경사와 지열류량 자료에 대한 인접 선구조의 방향은 북북동, 북서, 서북서 방향이 우세한 것으로 나타났다. 이는 우리나라 조구조 운동과 관련한 단층, 절리 등의 단열구조의 우세 방향과 잘 일치하는 것으로 해석된다.