Cutting power estimation can be used to select appropriate actuators in the design process of machine tools. Therefore, accurate estimation of cutting power is an important part of the design process. In this study, pipe cutting power is first calculated theoretically using the slotting cutting power equation and then verified experimentally. In this case, a pipe cutting machine is used to cut two pipes made of different materials. Power consumptions in the motor during pipe cutting are measured by using the embedded software, Labview, and NI hardware. The slotting cutting power equation can thus be confirmed easily comparing theoretically calculated cutting powers with experimentally measured cutting powers. The pipe materials used in this study are SUS304 and AL6N01. The specific cutting power of AL6N01 material is proposed through our cutting experiment. As a result, this cutting power can be used to design machining tools for AL6N01 material.
Journal of the Institute of Electronics Engineers of Korea SD
/
v.48
no.7
/
pp.76-81
/
2011
A new via cutting structure in 2-layer DRAM package substrate has been fabricated to lower its power distribution network(PDN) impedance. In new structure, part of the via is cut off vertically and its remaining part is designed to connect directly with the bonding pad on the package substrate. These via structure and substrate design not only provide high routing density but also improve the PDN impedance by shortening effectively the path from bonding pad to VSSQ plane. An additional process is not necessary to fabricate the via cutting structure because its structure is completed at the same time during a process of window area formation. Also, burr occurrence is minimized by filling the via-hole inside with a solder resist. 3-dimensional electromagnetic field simulation and S-parameter measurement are carried out in order to validate the effects of via cutting structure and VDDQ/VSSQ placement on the PDN impedance. New DRAM package substrate has a superior PDN impedance with a wide frequency range. This result shows that via cutting structure and power/ground placement are effective in reducing the PDN impedance.
Journal of the Microelectronics and Packaging Society
/
v.24
no.1
/
pp.91-101
/
2017
In this study, we conducted the preliminary research for high speed laser cutting of LED module. In particular, the feasibility of ultra-high speed laser cutting of 100 mm/s which exceeds the cutting speed of conventional dicing saw was examined. For this, copper/ceramic and silicone/ceramic hybrid substrates, which are the components of the LED module, were fabricated, and the surface morphology, surface roughness and flexural strength of the laser-cut samples were investigate and compared with the dicing-cut samples. To investigate optimal laser cutting conditions for hybrid substrates, the effects of various laser cutting conditions on cutting surface characteristics were studied using single ceramic and copper substrate. Optimal laser cutting conditions of the hybrid substrates were the use of Ar assist gas, high laser power and high assist gas pressure. Comparing the cutting surface of the hybrid substrates, the surface characteristics of the laser-cut samples are slightly inferior to those of the dicing-cut samples. The average surface roughness of the laser-cut samples was about $9{\mu}m$, and that of the dicing-cut samples was about $4{\mu}m$. However, considering very low cutting speed (3 mm/s) of the dicing saw, the surface morphology of the laser-cut sample was relatively uniform, and the surface roughness was not much different from that of the dicing-cut sample. The flexural strength of the laser-cut samples was equivalent to or slightly inferior to the flexural strength of dicing-cut samples. However, if the laser processing conditions are sufficiently optimized, the ultra-high speed laser cutting of the LED module will be possible.
With the recent increase in maintenance works on water and sewer pipes as well as district heating supply pipes, pavement cutting work using pavement cutter is on the rise. The pavement cutting operation generates considerable dust (cutting sludge) as well as noise; therefore, it is necessary to apply eco-friendly technologies that have low noise and dust recovery capability. Thus far, various equipment for recovering dust have been developed; however, there is a limitation in that the environmental friendliness is not quantified. Therefore, in this study, we developed a low-noise, dust-recovery type pavement cutter that can fundamentally remove the causes of environmental hazards such as noise and dust and evaluated the eco-friendliness of the pavement cutting process performed by this cutter. To this end, an integrated water cooling-sludge recovery system composed of a vacuum device and a sludge suction unit was developed, and the developed system was applied to a pavement cutter. Subsequently, the developed equipment was applied to the test bed, and data related to its eco-friendliness were collected and evaluated. The results showed that the cutting sludge recovery rate of the developed equipment was greater than 83%, the noise level was approximately 82 - 83 dB, and the sound power level was 115 dB. The results of this study will be used as basic data to develop improved pavement cutters in the future with improved cutting sludge recovery performance and lower noise.
O, Ji-Yong;Lee, Chang-Hyeon;Bae, Gang;Jin, Ik-Hyeon;Kim, Hwa-Min
Proceedings of the Korean Vacuum Society Conference
/
2016.02a
/
pp.166.2-166.2
/
2016
최근 생산 장비의 발달로 인해 절삭공구, 전기전자 부품, 항공 및 자동차 부품 생산에 필요한 생산 장비의 수명연장, 고속 절단 및 고성능화가 중요시 되면서 우수한 내구성, 내마모성 및 고온 안정성을 갖는 기계부품 및 공구를 요구하게 되었다. 내마모성을 가지는 표면을 얻기 위해서는 TiN, TiC, AlN, Al2O3, CrN, ZrO2와 같은 경도 높은 물질을 증착하여 특성을 개선시키는 방법이 있다. 특히 AlN은 비교적 우수한 경도와 고온 안정성을 가지고 있어, 생산 장비의 고속 절단 및 반복되는 정밀 작업으로 인한 열충격과 마모를 완화시키는 역할을 하는 코팅재로 사용하기 적합하다. 본 실험에서는 RF-magnetron sputtering 방법을 이용하여 AlN 박막을 파워 150W, 질소가스 분압비에 따라 25%, 50%, 75%, 100%의 조건으로 금속기판 위에 증착하였다. 금속 기판 위에 제작된 AlN막은 XRD (X-ray Diffraction)을 사용하여 배향성을 확인하였고, HM-220 (Micro-vickers hardness tester)을 사용하여 AlN박막의 경도를 측정하였으며, SEM (Scanning Electron Microscope), AFM (Atomic Force Microscope)을 이용하여 표면의 구조와 거칠기를 측정하였다. 이 실험을 통하여 우수한 물성과, 치밀한 조직의 AlN박막이 고속 절삭 공구, 유공압 실린더, 베어링과 같은 금속부품의 코팅소재로 적용가능 할 것으로 기대된다.
The Journal of Korean Institute of Communications and Information Sciences
/
v.26
no.12B
/
pp.1677-1685
/
2001
In this paper, we propose a call admission control scheme that can be performed within guaranteeing of required QoS(Quality of Services) in DS-CDMA(Direct Sequence-Code Division Multiple Access) reverse link. It has been performed rely on a physical channel numberonly and based on quality of received signal from MODEM(modulator/demodulator) part in established study. In other methods, the standard for services would have been set from statistical analysis of users\` location and using received power level in BTS(Base Transceiver Station). These ways bring about not only system loads but time delay or great differences from real environment. To solve these problems, we propose a call drop rate estimation algorithm for the purpose of call admission control based on measured value at LNA(Low Noise Amplifier) ports of BTS(Base Transceiver Station) in real time. This method proposed in this paper estimates a quality of offered service in real time, reduce system loads and shorten time delay which is needed to determine the standard for call admission control. But it requires a additional 17W complexity which can measure received signal power in BTS and estimate call drop rate.
Park, Ju-Hong;Lee, Seong-Hyeon;No, Ho-Seop;Choe, Gyeong-Hun;Jo, Gwan-Sik;Lee, Je-Won
Proceedings of the Materials Research Society of Korea Conference
/
2009.05a
/
pp.39.1-39.1
/
2009
본 실험은 연성과 광 투명도가 뛰어난 아크릴 (PMMA) 과 폴리카보네이트 (Polycabonate) 기판의 축전 결합형 플라즈마 (CCP) 건식 식각 연구에 관한 것이다. 특히 식각 반응기 내부의 압력 변화에 따른 두 기판의 건식 식각 특성 분석에 초점을 맞추었다. 실험에 사용된 기판은 두께 1mm의 아크릴 (PMMA) 과 폴리카보네이트 (Polycabonate)를 $1.5\times1.5\;cm^2$로 절단하여 Photo-lithography 공정을 통하여 감광제 (Photo-resist)로 패턴하였다. 식각 반응기 내부에 패턴 된 아크릴(PMMA) 과 폴리카보네이트 (Polycabonate)를 넣은 후 반응기 내부 진공 상태로 만들었다. 그 후 5 sccm $O_2$ 가스를 유량조절기 (Mass flow controller)를 통하여 식각 반응기 내부로 유입하여 실험을 하였다. 이때 식각 공정 변수는 식각 반응기 내부 압력과 샘플 척 파워이다. 특성평가 항목은 식각 후 기판 (Substrate)의 식각율 (Etch rate), 식각 선택비 (Selectivity) 그리고 기판 표면 거칠기 (RMS roughness)이다. 실험 결과는 표면 단차 분석기(Surface profiler)를 이용하여 기판 (Substrate)의 표면을 분석 하였다. 또한 OES (Optical Emission Spectroscopy) 를 이용하여 식각 중 내부 플라즈마의 상태를 분석하였다. 본 실험 결과에 따르면 5 sccm $O_2$ 가스와 100 W 척 파워를 고정한 후 반응기 내부의 압력을 25 mTorr에서 180 mTorr까지 변화시켜 실험한 결과 40 mTorr의 반응기 내부 압력에서 실험 자료 중 가장 높은 식각율로 아크릴 (PMMA)은 $0.46\;{\mu}m/min$, 폴리카보네이트 (Polycabonate)는 $0.28\;{\mu}m/min$의 결과를 얻었다. 또한 이 자료를 바탕으로 5 sccm $O_2$ 가스와 반응기 내부 압력을 40 mTorr로 고정시키고 RIE 척 파워를 25 W에서 150 W로 증가시켰을 때 아크릴 (PMMA)의 식각율은 $0.15\;{\mu}m/min$에서 $0.72\;{\mu}m/min$까지 증가하였고, 폴리카보네이트 (Polycabonate) 의 식각율은 $0.1\;{\mu}m/min$에서 $0.36\;{\mu}m/min$까지 증가하였다.
파장분할 다중방식 광통신망(WDM -PON) 운영의 신뢰성을 높이기 위해 각 광 채널의 파장과 파워, 그리고 광섬유로 이어진 링크(link)의 절단상태 등을 모니터링(monitoring)하는 것은 필수적이다. 본 원고에서는 이러한 목적을 효율적이고 경제적으로 달성하기 위해 제시되고 검증되었던 방법들을 pilot tone을 이용한 방법, AWG, FBG, tunable filter 등의 파장 선택성 소자를 이용한 방법, electrical processing을 이용한 방법 등의 세 가지로 나누어 소개한다.
Gravity characteristics are investigated in the vicinity of the DASAN scientific station, located at the Svalbard Archipelago, the Arctic using ArcGP data. Boundary effects of free-air gravity anomalies, which appeared generally at the continental margin, are erased after Bouguer correction was applied. Complete Bouguer anomalies produced after terrain correction by GrOPO30 show that gravity anomalies increase from continent to marine. This phenomena seem to be related to the rise of Moho discontinuity. The cut-off frequency of 0.16 was decided after power spectrum analysis and the gravity anomalies were divided into two parts. Residual anomalies in high frequency part show that characteristics of high values along the faults and of low values related to thick sediments in the continent. Characteristic is low values from basement subsidence of continental slope or thick sediments in the marine. The undulation of Moho discontinuity from 3-D inversion modeling show typical characteristics of continental margin that become higher from Svalbard archipelago to Knipovich ridge bordering Eurasian plate.
Yu Sang Hoon;Kim Chang Hwan;Hwang Jong Sun;Min Kyung Duck
한국지구물리탐사학회:학술대회논문집
/
2005.05a
/
pp.255-260
/
2005
A Gravity characteristic of Svalbard archipelago in Arctic was studied by using ArcGP data. There are situated the Dasan science station. After bouguer correction, an edge effect of free-air anomaly, which is similar to topography, are not shown at passive continent margin, and after terrain correction with GTOPO30 data, gravity anomaly increases from continent to marine. that is deep connected with rise of Moho discontinuity. The correlation of topography and free-air anomaly shows that the isostasy of continent attains a little less than marine. After filtering, the residual anomaly are shown high and low anomalies related to fracture zone in continent and base depression or thick sedimentary layer in continental slope, marine.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.