The aim of this study was to investigate the influence of four different light curing modes on the marginal leakage of Class V composite resin restoration. Eighty extracted human premolars were used. Wedge-shaped class Y cavities were prepared on the buccal surface of the tooth with high-speed diamond bur without bevel. The cavities were positioned half of the cavity above and half beyond the cemento-enamel junction. The depth, height, and width of the cavity were 2 mm, 3 mm and 2 mm respectively. The specimens were divided into 4 groups of 20 teeth each. All the specimen cavities were treated with Prime & Bond$^{R}$ NT dental adhesive system (Dentsply DeTrey GmbH, Germany) according to the manufacturer's instructions and cured for 10 seconds except group VI which were cured for 3 seconds. All the cavities were restored with resin composite Spectrum$^{TM}$ TPH A2 (Dentsply DeTrey GmbH, Germany) in a bulk. Resin composites were light-cured under 4 different modes. A regular intensity group (600 mW/${cm}^2$, group I) was irradiated for 30 s, a low intensity group (300 mW/${cm}^2$, group II) for 60 s and a ultra-high intensity group (1930 mW/${cm}^2$, group IV) for 3 s. A pulse-delay group (group III) was irradiated with 400 mW/${cm}^2$ for 2 s followed by 800 mW/${cm}^2$ for 10 s after 5 minutes delay. The Spectrum$^{TM}$ 800 (Dentsply DeTrey GmbH, Germany) light-curing units were used for groups I, II and III and Apollo 95E (DMD, U.S.A.) was used for group IV. The composite resin specimens were finished and polished immediately after light curing except group III which were finished and polished during delaying time. Specimens were stored in a physiologic saline solution at 37$^{\circ}C$ for 24 hours. After thermocycling (500$\times$, 5-55$^{\circ}C$), all teeth were covered with nail varnish up to 0.5 mm from the margins of the restorations, immersed in 37$^{\circ}C$, 2% methylene blue solution for 24 hours, and rinsed with tap water for 24 hours. After embedding in clear resin, the specimens were sectioned with a water-cooled diamond saw (Isomet$^{TM}$, Buehler Co., Lake Bluff, IL, U.S.A.) along the longitudinal axis of the tooth so as to pass the center of the restorations. The cut surfaces were examined under a stereomicroscope (SZ-PT Olympus, Japan) at ${\times}$25 magnification, and the images were captured with a CCD camera (GP-KR222, Panasonic, Japan) and stored in a computer with Studio Grabber program. Dye penetration depth at the restoration/dentin and the restoration/enamel interfaces was measured as a rate of the entire depth of the restoration using a software (Scion image, Scion Corp., U.S.A.) The data were analysed statistically using One-way ANOVA and Tukey's method. The results were as follows : 1. Pulse-Delay group did not show any significant difference in dye penetration rate from other groups at enamel and dentin margins (p>0.05) 2. At dentin margin, ultra-high intensity group showed significantly higher dye penetration rate than both regular intensity group and low intensity group (p<0.05). 3. At enamel margin, there were no statistically significant difference among four groups (p>0.05). 4. Dentin margin showed significantly higher dye penetration rate than enamel margin in all groups (p<0.05).
IMPACT Silver 주식회사는 Zacualpan 프로젝트의 Royal Mines(이하 로얄 광산)을 인수했다. $124.5\;km^2$에 해당하는 지역의 소유권은 두 개의 멕시코 사기업으로부터 가행중인 광산의 채굴권 구입과 운영 중인 기반시설의 임대를 조건으로 한다. 프로젝트 지역은 멕시코시티로부터 남서방향으로 100 km와 Taxco Silver 광산으로부터 북서방향으로 25 km 떨어진 지점에 위치한다. 기반시설은 비포장 도로, 충분한 전력과 물의 공급 및 숙련공들을 갖추어 우수한 평가를 받고 있다. 소유권은 멕시코인의 개인소유 하에서 무한한 매장량 혹은 자원량을 갖고 운영된 채광과 가공시설을 인수하는 것이다. 소유권 지역을 대상으로 한 IMPACT Silver사의 주 탐사목적은 이미 알려진 광화대의 확장을 위한 잠재성 평가와 다른 지역에서 신규 광상의 유망지역을 발견하는 것이다. Zacualpan 프로젝트의 로얄 광산은 남동 Guerrero terrane의 북부에 위치한다. Teloloapan subterrane은 주로 저변성 녹색편암상으로 구성된 쥬라기 후기에서 백악기 초기의 화산성 퇴적층으로 구성된다. 대부분의 유망지역은 Lower Villa de Ayala층의 중성 내지 염기성 화산성 쇄설암을 모암으로 한다. 다상의 변성작용은 지역 전반에 걸쳐 나타나고, Zacualpan 광산지역에서 수반되는 광화작용을 규제한다. Zacualpan 광산지역은 Sierra Madre del Sur로 알려진 유망 광화대에 해당한다. 이 지역은 화산성 괴상 황화광상과 천열수 맥상광상이 우세하다. 대부분의 천열수 광화작용은 3.2-3.8억 년 전 마그마의 생성이 활발한 판구조 체제 동안 발생하였다. 역사적으로 가장 주요한 지역은 Lipton Vein이다. 현재 Zacualpan 지구에서 채광량은 은 200-500 g/t 정도로 보고되고 있다. 일부 지역은 고품위 은 광화작용(은 1,000 g/t 이상)을 수반하고 있으며, 이는 탐사의 주 타겟이 되고 있다. Zacualpan에서 은 광화작용은 은이 부화된 중유황 천열수 맥상광상으로 상당히 유명하다. Fresnillo, Pachuca 및 Taxco 광산을 포함한 멕시코 소유의 대규모의 잘 알려진 광산들이 이에 해당한다. 이러한 광산들은 부산물로서 금, 아연, 연이 생산된다. 이러한 광상들은 맥상과 각력상 및 산점상 또는 망상세맥의 형태로 산출된다. 광화작용은 석영과 탄산염 맥 내에 주로 황철석과 다양한 섬아연석, 방연석, 은 혹은 금 광물들을 수반한다. 경제성을 갖는 광화작용의 수직적인 연장은 평균적으로 대략 300 m이고, 멕시코 중부에 위치한 Fresnillo의 광화작용은 100 m에서 960 m의 연장을 갖는 것으로 알려져 있다. 아주 오랫동안 Zacualpan에서 광산관계자의 관측과 IMPACT Silver에서 최근 작업의 결과를 토대로, Zacualpan 광산지역의 탐사모델은 새로운 광상의 탐사를 위한 가이드로서 개발되었다. Zacualpan 광산지역에서 가장 높은 경제성을 갖는 광화작용은 북서와 남북방향의 맥 구조를 따라 수반된다. 이러한 맥 구조들은 종종 이 지역을 가로질러 수 km까지 추적되지만, 경제성을 갖는 광화작용은 맥 구조를 따라서 구조적으로 유리한 지역에서 부광대를 형성한다. 부광대를 형성하기 위한 가장 유리한 구조적 지역은 북서와 남북방향으로 발달한 맥 구조들이 교차하는 지역이다. 지난 30년간 채광된 주요 부광대는 폭이 2-6 m 이고 수평연장은 30-150 m 그리고 수직연장은 230-300 m에 이른다. 가장 높은 생산량을 보이는 부광대는 남북방향의 이차 맥들이 Guadalupe 광산의 Lipton 맥을 가로지르는 지역에서 발달한다. 남동쪽으로 현재 Compadres 광산의 Silver Shoot No. 1으로부터 고품위 은을 생산하는 지역은 북서방향의 San Agustin 맥이 북향의 Cometa Navideno 맥에 의해 절단되는 지역에서 산출한다. 모암은 광화작용을 규제하는 또 다른 중요한 요소이다. 광산지역에서 경제성을 갖는 모든 광화작용은 중성 내지 염기성 화산암 특히 안산암과 관련 모암에 배태된다. 부광대가 셰일 혹은 편암으로 전이되는 지역에서, 맥들은 소규모의 세맥으로 나뉘어 진다. Zacualpan의 전형적인 천열수 광상에서 부광대는 상부로 가면서 은의 함량이 증가하고, 하부로 가면서 연 아연의 함량이 증가하는 수직적 대상을 보인다. 금의 함량 변화는 보다 예측이 어려우나 상당히 중요하다. Zacualpan 광산지역의 탐사모델에 사용된 토양 채취, 정밀지도제작, 트렌치 및 시추탐광은 현재 IMPACT Silver사가 이 지역을 대상으로 한 가장 효율적인 탐사방법으로 입증되었다. Zacualpan 프로젝트의 로얄 광산은 하루 500 톤을 제련하는 기반시설과 수반된 채굴권을 갖는 가행 광산들을 포함한다. 현재 IMPACT Silver사는 두 곳의 타겟 지역에서 정밀지도제작, 토양 및 암석 채취, 12공 총 1866 m의 시추탐광에 의한 사전조사로 구성된 4 단계 탐사를 수행했다. 암석 1,953개, 토양 1,631 개, 389 개의 시추코어 시료가 채집되고 분석되었다. 이러한 작업은 추가탐사를 요구하는 수많은 유망 광화대를 규명했다. Compadres 광산에서 현재 가행중인 지하갱 시료는 레벨 1에서 0.9 m의 폭을 갖는 광체에서 은 680 g/t과 금 0.3 g/t, 레벨 3에서 1.67 m의 폭을 갖는 광체에서 은 12,591 g/t과 금 12.07 g/t의 품위를 갖는 것으로 나타났다. 레벨 1에서 3까지 2-3 m의 폭과 30-40 m 연장으로 채광되었다. 시추탐광은 고품위를 갖는 몇몇의 중첩된 맥을 발견했다. Compadres 광산에서 남동방향으로 200 m지점에 위치한 Soledad 지역에서 5 개의 시추공으로부터 동일 맥 시스템이 발견되었고, 고품위 부광대의 상부로 간주되는 몇몇 중요 지점이 발견되었다. 초기 단계의 탐사는 유망 시추탐광 지역인 중간정도 내지 고품위 유망 광화대를 규명했다.
Statement of problem: Problems such as loosening and fractures of retained screws and fracture of implant fixture have been frequently reported in implant prosthesis. Purpose: Implant has weak mechanical properties against lateral loading compared to vertical occlusal loading, and therefore, stress analysis of implant fixture depending on its material and geometric features is needed. Material and methods: Total 28 of external hexed implants were divided into 7 of 4 groups; Group A (3i, FULL $OSSEOTITE^{(R)}$Implant), Group B (Nobelbiocare, $Br{\aa}nemark$$System^{(R)}$Mk III Groovy RP), Group C (Neobiotec, $SinusQuick^{TM}$ EB), Group D (Osstem, US-II). The type III gold alloy prostheses were fabricated using adequate UCLA gold abutments. Fixture, abutment screw, and abutment were connected and cross-sectioned vertically. Hardness test was conducted using MXT-$\alpha$. For fatigue fracture test, with MTS 810, the specimens were loaded to the extent of 60-600 N until fracture occurred. The fracture pattern of abutment screw and fixture was observed under scanning electron microscope. A comparative study of stress distribution and fracture area of abutment screw and fixture was carried out through finite element analysis Results: 1. In Vicker's hardness test of abutment screw, the highest value was measured in group A and lowest value was measured in group D. 2. In all implant groups, implant fixture fractures occurred mainly at the 3-4th fixture thread valley where tensile stress was concentrated. When the fatigue life was compared, significant difference was found between the group A, B, C and D (P<.05). 3. The fracture patterns of group B and group D showed complex failure type, a fracture behavior including transverse and longitudinal failure patterns in both fixture and abutment screw. In Group A and C, however, the transverse failure of fixture was only observed. 4. The finite element analysis infers that a fatigue crack started at the fixture surface. Conclusion: The maximum tensile stress was found in the implant fixture at the level of cortical bone. The fatigue fracture occurred when the dead space of implant fixture coincides with jig surface where the maximum tensile stress was generated. To increase implant durability, prevention of surrounding bone resorption is important. However, if the bone resorption progresses to the level of dead space, the frequency of implant fracture would increase. Thus, proper management is needed.
Lee, Moon Soo;Kang, Gil Ho;Cho, Gyu Seok;Kim, Yong Jin;Kim, Sung Yong;Baek, Moo Jun;Kim, Chang Ho;Cho, Moo Sik
Journal of Gastric Cancer
/
v.7
no.1
/
pp.31-37
/
2007
Purpose: A pancreas-preserving total gastrectomy (PPTG) was introduced to decrease the postoperative complications due to pancreatic resection. However, some complications, such as leakage of pancreatic juice, are still reported. Thus, the purpose of this study was to propose a supplementary procedure based on the results of treatment for gastric cancer at our hospital. Materials and Methods: From Jan. 1997 to Dec. 2004, the cases of 141 patients who underwent a PPTG for gastric cancer were reviewed retrospectively. The patients were divided into Group A (38 cases), patients who were treated using a conventional PPTG, and Group B (103 cases), patients who were treated using a new and improved PPTG. Their postoperative complications were compared. Results: No statistically significant differences in clinicopathologic data were noted between the two groups. The comparison of complications showed for groups A and B, respectively, 4 and 0 cases of pancreatic fistula, 1 and 0 cases of intraabdominal abscess, 2 and 0 cases of intraoperative pancreatic necrosis, and 2 and 2 cases of minor leakage. The difference in the prevalence of complications between the two groups was statistically significant (P=0.0001). Conclusion: In order to reduce the risk of PPTG-related complications, we used vascular clamps to observe the necrosis of the pancreatic tail before dividing the splenic artery, and this method resulted in a significant decrease in postoperative complications. Thus, we conclude that our use of vascular clamps in a PPTG is a simple and useful method for preventing postoperative complications.
Journal of the korean academy of Pediatric Dentistry
/
v.33
no.2
/
pp.233-243
/
2006
The aim of this study was to investigate the relationship between the C-factor and shrinkage strain values of composite resin and examine the strain values in different incremental filling techniques. Experiment consisted two aims. First, we compared with strain value in two different C-factors(3.7 and 1.0). Second, we examined the strain values in three different filling techniques. The results of the present study can be summarized as follows : 1. High C-factor groups showed higher contraction stress values than low C-factor groups at 900 sec after polymerization. 2. Hybrid resin showed higher contraction stress values than flowable resin in high C-factor cavities. But contraction stress was not revealed significant difference between hybrid resin and flowable resin in low C-factor cavities (P>0.05). 3. Bulk felling with hybrid resin(Group 1) showed high contraction stress and lining with flowable resin followed hybrid resin (Group 5) showed lower contraction stress. 4. Contraction stress were increased during 900 sec after polymerization in high C-factor groups but decreased gradually after 900 sec. 5. Low C-factor groups showed tight marginal seal between resin and cavity wall but high C-factor groups showed gaps formed between resin and cavity wall in part. On the basis above results, layering techniques in high C-factor cavity showed advantages in reducing contraction stress and gap formation between cavity wall and resin restoration.
Two types of fiat-plate collector were designed and constructed for utilizing the solar energy as heating source of red pepper drying. It was performed to investigate the basic factors on using the collectors and the drying effect on various types of red pepper, and the results obtained are summarized as follows. 1. The optimum tilted angles of the collector in Daejeon area were ${\phi}-15^{\circ}$ in summer season and ${\phi}+15^{\circ}$ in winter season when it was adjusted two times per a year: 2. In the conditions during experiment period, average atmospheric temperature and relative humidity were $25.6^{\circ}C$ and 52.6%, respectively, and $42.0^{\circ}C$, 74.2% in the control chamber. The temperature in the drying chamber connected to the water heater was the highest but relative humidity in the chamber connected to the air heater was the lowest among the chambers. 3. The drying velocity of whole red pepper in the chamber connected to the water heater was the fastest as 2.3 times as compared to the whole type on the mat drying followed by air heater and control in decreasing order. The horizontally cut red pepper in the chamber connected to the water heater was dried exceedingly fast among twelve plots. 4. The content of capsaicine as pungent principle and of capsanthine as red pigment in the red pepper were reduced during drying but there were no differences significantly on the drying method, and it could not affect much on the quality of dried product.
Statement of problem: Microleakage at the occlusal and gingival margin of Class V cavities restored with composite resin has traditionally been considered an obstacle to successful restoration. Purpose: The aim of this study was to assess the effectiveness of three different surface sealants(Fortify, Permaseal and Biscover LV) on the marginal sealing of Class V light-activated composite resin restorations(Z250). Material and methods: Forty noncarious human premolars and molars extracted within a three-month period were selected. Class V cavities with the occlusal margin in enamel and gingival margin in cementum were prepared in both buccal and lingual surfaces. The teeth, randomly assigned in four groups with twenty cavities in each group, were restored with composite resin after applying an adhesive system(Clearfil SE bond). After the finishing and polishing procedures, the restorations were covered with a specific surface sealants, except for the control samples, which were not sealed. After placing restorations, the specimens were thermocycled, and immersed in a 2% methylene blue solution for twenty four hours and sectioned longitudinally. The marginal microleakage was evaluated at the occlusal and gingival interfaces using a microscope and compared among the four groups using ANOVA test and Wilcoxon Rank-Sum test($\alpha$=0.05). Results: Statistical analysis showed that there was significantly less leakage when the surface sealants were used than there was in control group(P<.05). There were no significant differences of microleakage at occlusal and gingival margins among groups. There were no significant differences between microleakage of occlusal and gingival margins in each group. Fortify was not statistically different from control group at the gingival margin(P>.05). Conclusion: Application of surface sealants was an effective method of surface coating in reducing microleakage at occlusal and gingival margins of Class V composite resin restorations. However, it is certain that some microleakage still occurred despite the application of surface sealants, especially gingival margins.
This study was done to evaluate the reliability of the digital color analysis system (ShadeScan, CYNOVAD, Montreal. Canada) for dentistry. Sixteen tooth models were made by injecting the A2 shade chemical cured resin for temporary crown into the impression acquired from 16 adults. Surfaces of the model teeth were polished with resin polishing cloth. The window of the ShadeScan handpiece was placed on the labial surface of tooth and tooth images were captured, and each tooth shade was analyzed with the ShadeScan software. Captured images were selected in groups, and compared one another. Two models were selected to evaluate repeatability of ShadeScan, and shade analysis was performed 10 times for each tooth. And, to ascertain the color difference of same shade code analyzed by ShadeScan, CIE $L^*a^*b^*$values of shade guide of Gradia Direct (GC, Tokyo, Japan) were measured on the white and black background using the Spectrolino (GretagMacbeth, USA), and Shade map of each shade guide was captured using the ShadeScan. There were no teeth that were analyzed as A2 shade and unique shade. And shade mapping analyses of the same tooth revealed similar shade and distribution except incisal third. Color difference (${\Delta}E^*$) among the Shade map which analyzed as same shade by ShadeScan were above 3. Within the limits of this study, digital color analysis instrument for dentistry has relatively high repeatability, but has controversial in accuracy.
The distensibility of the major arteries has been investigated extensively, but the value expressed as Young Modulus varies widely by the different schools of the investigators, the major reason undoubtedly being the difficulties encountered in the measurement. In the present study, an attempt was made to elucidate the distensibility of the external carotid artery of the rabbit, which was placed in saline immediately after removing from the apparently healthy, normal rabbit without anesthesia. The circular section strip and longitudinal section strip were made from the whole artery, and Young Modulus of the whole artery, circular section and longitudinal section strips was calculated from the length-tension curve of each sample. Also, the similar samples of the artery seperately obtained were placed in ATP solution in the concentration of 0.15 mM and 0.30 mM, and Young Modulus was similary calculated. Experiments were performed at 15,45 and 75 min after the artery was removed from the rabbit, and the results thus obtained are summarized as follows. 1) Young Modulus of the whole external carotid artery of the rabbit in saline was $4.74{\times}10^7dyne/cm^2$ at 15 min, but lower values were obtained at 45 and 75 min, Young Modulus being $4.62{\times}10^7dyne/cm^2\;and\;4.13{\times}10^7dyne/cm^2$, respectively. When the arterial samples were placed in ATP solutions, Young Modulus did not change much throughout the experiment, and lower Young Moduli were obtained in 0.30 mM ATP solution than in 0. 15 mM ATP solution. 2) Young Modulus Of the Circular Section Strip in Saline was $4.11{\times}10^7dyne/Cm^2,\;3.75{\times}10^7dyne/cm^2\;and\;3.90{\times}10^7dyne/cm^2,$ respectively, at 15, 45 and 75 min, the value at 15 min being the highest. However, when the strip was placed in ATP solutions, no appreciable change was observed throughout the experiment, and Young Moduli were lower in 0.30 mM ATP solution than in 0.15 mM ATP solution. 3) Young Modulus of the longitudinal section strip in saline was $2.12{\times}10^7dyne/cm^2,\;2.48{\times}10^7dyne/cm^2\;and\;2.46{\times}10^7dyne/cm^2$, respectively, at 15, 45 and 75 min, Young Modulus being slightly elevated in the latter part of the experiment. A similar tendency was observed when the strip was placed in ATP solutions.
These experiments were carried out to define the effects of NAA, 2, 4-D and Benzyladenine on the callus induction and the organ differentiation from the explants and to find out the vegetative propagation method of Korean ginseng. The results obtained are summarized as follows; 1. NAA was significantly effective in forming roots from the ginseng stem segment and the number of roots was increased by increasing NAA concentration in the medium. The roots were formed from both distal and proximal ends of the ginseng stem segments grown on the medium containing more than 2mg/L of NAA. 2. The amount of callus growth increased proportionatly with NAA concentration in the range of 4.0mg per liter in the medium. The callus was easly induced from stem segment than leaf segment and 2, 4-D was more effective in callus induction and growth than NAA. 3. The benzyladenine showed the significant inhibition effect in forming roots from ginseng explant. The callus was not induced with BA alone, but in BA and 2, 4-D or BA and NAA added medium, the callus was easily induced and its growth was also accelerated. The interaction effects between 2, 4-D and BA on the callus induction and growth were significantly higher than those between NAA and BA. 4. As the ginseng embryos were cultured on the M.S. medium supplemented with 2mg per liter NAA, number of shoots was significantly increased and the percentage of embryo which had shown more than 4 shoots later was 22.2%. On the medium containing 8mg per liter NAA, the ginseng embryo showed the normal growth of shoots and leaves, but increased roots and callus induction on the basal part of shoots. 5. When the shoots with 3 leaflets were cut in 1.5cm long and grown on the Blayde's medium containing NAA 1.0mg per liter, roots were formed at the proximal end of shoot, and a new ginseng seedling was successfully obtained.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.