• Journal of the Korean Chemical Society
• /
• v.60 no.3
• /
• pp.187-193
• /
• 2016

In this study, preparation of positively and negatively charged carbon nanotube (CNT)-collagen (CG) hydrogels with pH sensitive characteristic was reported. The positive and negative characteristics of the prepared hydrogels were created by introduction of positively functionalized CNT-NH₂ and negatively functionalized CNT-COOH, respectively, into the collagen hydrogel. The surface charge of CNTs (CNT-NH₂ and CNT-COOH), CG and CNTs/CG hydrogels was measured by Zetasizer. The swelling ratios of CNT-NH₂/CG and CNT-COOH/CG hydrogels in aqueous solution were checked by measuring of weight changes of the hydrogels in the range of pH 2~10. In detail, the positively charged CNT-NH₂/CG hydrogel swelled up to 5% at pH 4 in comparison to the weight at pH 7, while the negatively charged CNT-COOH/CG hydrogel swelled up to 10% at pH 10. The prepared CNT-NH₂/CG and CNT-COOH/CG hydrogels will be very useful as pH sensitive oral drug-delivering systems for gastrointestine (pH ~2) and small intestine (pH ~9), respectively.

• Applied Chemistry for Engineering
• /
• v.32 no.5
• /
• pp.509-515
• /
• 2021

In this study, poly lactic-co-glycolic acid (PLGA) nanoparticles (PNP) were prepared through double (w/o/w) emlusion and emulsifying solvent-evaporation technique using PLGA, which has biocompatibility and biodegradability. To maximize stability and bioavailability of the particles, chitosan-coated PLGA nanoparticles (CPNP) were prepared by charge interaction between PNP and chitosan. We demonstrated that CPNP can be utilized as a drug carrier of oral administration. The chemical structure of CPNP was analyzed by ¹H-NMR and FT-IR, and all characteristic peaks appeared, confirming that it was successfully prepared. In addition, particle size and zeta potential of CPNP were analyzed using dynamic light scattering (DLS) while morphological images were obtained using transmission electron microscope (TEM). Thermal decomposition behavior of CPNP was observed through thermogravimetric analysis (TGA). In addition, the cytotoxicity of CPNP was confirmed by MTT assay at HEK293 and L929 cell lines, and it was proved that there is no toxicity confirmed by the cell viability of above 70% at all concentrations. These results suggest that the CPNP developed in this study may be used as an oral drug delivery carrier.

• Journal of the Korean Chemical Society
• /
• v.51 no.1
• /
• pp.43-50
• /
• 2007

Liposomes having particle size from several tens to hundreds nanometers are efficient carriers for injectable drug delivery. Enhancement of liposome stability in bloodstream has been studied because of its relatively short circulation time and fast clearance from human body by reticuloendothelial system (RES) in blood vessel. In this study, new disaccharide-1,2-distearoyl-sn-glycero-3-phosphoethanolamine (DSPE) derivatives in which lactose or sucrose as the disaccharide molecule was conjugated covalently to DSPE were synthesized. Liposomes of which surface had disaccharide molecules were prepared by incorporating the disaccharide-DSPE into liposomes as one of their lipid components. Particle size of the prepared liposomes was approximately 100 nm. The liposomes of which surface were modified with the disaccharide-DSPE showed -25 mV of zeta potential value due to the presence of hydroxyl groups on their surface, while the unmodified control liposomes showed -10 mV of zeta potential value. Loading efficiency of model drug, doxorubicin, into liposomes was about 90%. Stability of the disaccharide-modified liposomes in vitro was evaluated by monitoring the amount of protein adsorption and particle size of the liposomes in serum. Disaccharide-modified liposomes were more stable in serum than unmodified control liposomes or polyethyleneglycol (PEG)-modified liposomes due to less adsorption of serum protein and hence less increase of their particle size. The liposomes of which surface was modified with disaccharide-DSPE conjugate can be used as long-circulating carriers for drugs having high toxicity or short half-life time due to their enhanced stability in blood circulatory system.

• Journal of the Korean Electrochemical Society
• /
• v.20 no.1
• /
• pp.7-12
• /
• 2017

Using a precursor of $LiNi_{0.6}Co_{0.2}Mn_{0.2}O_2$ as a starting material, a surface-modified cathode material was obtained by coating with KCl, where the added KCl reduces residual Li compounds such as $Li_2CO_3$ and LiOH, on the surface. The resulting electrochemical properties were investigated. The amounts of $Li_2CO_3$ and LiOH decreased from 8,464 ppm to 1,639 ppm and from 8,088 ppm to 6,287 ppm, respectively, with 1 wt% KCl added $LiNi_{0.6}Co_{0.2}Mn_{0.2}O_2$ that had been calcined at $800^{\circ}C$. X-ray diffraction results revealed that 1 wt% of KCl added $LiNi_{0.6}Co_{0.2}Mn_{0.2}O_2$ did not affect the parent structure but enhanced the development of hexagonal crystallites. Additionally, the charge transfer resistance ($R_{ct}$) decreased dramatically from $225{\Omega}$ to $99{\Omega}$, and the discharge capacity increased to 182.73mAh/g. Using atomic force microscopy, we observed that the surface area decreased by half because of the exothermic heat released by the Li residues. The reduced surface area protects the cathode material from reacting with the electrolyte and hinders the development of a solid electrolyte interphase (SEI) film on the surface of the oxide particles. Finally, we found that the introduction of KCl into $LiNi_{0.6}Co_{0.2}Mn_{0.2}O_2$ is a very effective method of enhancing the electrochemical properties of this active material by reducing the residual Li. To the best of our knowledge, this report is the first to demonstrate this phenomenon.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.8B
• /
• pp.691-700
• /
• 2006

Based on the destination IP address of incoming packets, the Internet routers determine next hops and forward packets toward final destinations through If address lookup. The bandwidth of communication links increases exponentially fast as well as the routing table size grows significant as the number of single host networks attached to the Internet increases. Since packets should be processed at wire-speed, the increased link speed reduces the processing time of a packet in routers, and hence more efficient and fast IP address lookup algorithms and architectures are required in the next generation routers. Most of the previous IP lookup schemes compare routing prefixes of shorter length first with a given input IP address. Since IP address lookup needs to find the most specific route of the given input, search continues until the longest matched prefix is found while it keeps remembering the current test matching prefix. In this paper, based on binary search on prefix length, we proposed a new IP address lookup algorithm which compares longer prefixes first. The proposed scheme is consisted of multiple tries with prefixes on leaves only. The trie composed of the longest prefixes is primarily searched whether there is a match with the given input. This processing is repeated for the trio of the next longer prefixes until there finds a match. Hence the proposed algorithm provides the fast search speed. The proposed algorithm also provides the incremental update of prefixes while the previous binary search on length scheme does not provide the incremental update because of pre-processing requirement. In this paper, we performed extensive simulations and showed the performance comparisons with related works.

• Corrosion Science and Technology
• /
• v.8 no.2
• /
• pp.53-61
• /
• 2009

In this study, both evaluations by visual imaging for exterior view of coating and by EIS were executed for epoxy primer coated specimens deteriorated by accelerated test, and comparison and analysis were carried out for 2 evaluation methods. In the comparison between total damaged area ratio acquired by image processing method and deterioration point, higher deterioration points were appeared for rusted specimens than for non-rusted specimens. It is attributed that deterioration point per unit area ratio given for rust is higher than for peeling. In the comparison between total damaged area ratio and EIS result, impedance of coating was largely decreased as about TEX>$10^4{\Omega}{\cdot}cm^2$ or less when rust area ratio is more than about 0.1%, and blistering area ratio is more than about 3%. Charge transfer resistance ($R_{ct}$) and double layer capacitance ($C_{dl}$) values were appeared for all specimens except 2 ones, which shows that water is accumulated and steel substrate is corroded at coated film-steel interface. In the comparison between deterioration point and EIS result, more than 10 points as deterioration point were given for specimens of below $10^6{\Omega}{\cdot}cm^2$ of impedance at low frequency. For specimens deteriorated by NORSOK cyclic test, impedance was lowest of all, though deterioration point was not high. It is thought to be attributed that coating system and accelerated deterioration condition of cyclic tested specimens were different from those of main specimens. From the result, it is thought that coating resistance can be relatively more decreased than deterioration degree estimated from exterior view under more severe corrosion environment or in the present of more complex deterioration factors.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3626-3631
• /
• 2009

This study has provided some of the first experimental results of NMOSFET hot-carrier degradation for the analog circuit application. After hot-carrier stress under the whole range of gate voltage, the degradation of NMOSFET characteristics is measured in saturation region. In addition to interface states, the evidences of hole and electron traps are found near drain depending on the biased gate voltage, which is believed to the cause for the variation of the transconductance($g_m$) and the output conductance($g_{ds}$). And it is found that hole trap is a dominant mechanism of device degradation in a low-gate voltage saturation region, The parameter degradation is sensitive to the channel length of devices. As the channel length is shortened, the influence of hole trap on the channel conductance is increased. Because the magnitude of $g_m$ and $g_{ds}$ are increased or decreased depending on analog operation conditions and analog device structures, careful transistor design including the level of the biased gate voltage and the channel length is therefore required for optimal voltage gain ($A_V=g_m/g_{ds}$) in analog circuit.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.6
• /
• pp.527-534
• /
• 2015

This study offers a novel method for improving the physical contact between the anode and fuel in a direct carbon fuel cell (DCFC): a direct generation of carbon in a porous Ni anode through the thermal decomposition of gaseous hydrocarbons. Three kinds of alkane hydrocarbons with different carbon numbers (CH4, C2H6, and C3H8) are tested. From electron microscope observations of the carbon particles generated from each hydrocarbon, we confirm that more carbon spheres (CS), carbon nanotubes (CNT), and carbon nanofibers (CNF) were identified with increasing carbon number. Raman scattering results revealed that the carbon samples became less crystalline and more flexible with increasing carbon number. DCFC performance was measured at $700^{\circ}C$ with the anode fueled by the same mass of each carbon sample. One-dimensional carbon fuels of CNT and CNF more actively produced and had power densities 148 and 210 times higher than that of the CS, respectively. This difference is partly attributed to the findings that the less-crystalline CNT and CNF have much lower charge transfer resistances than the CS.

• Membrane Journal
• /
• v.27 no.4
• /
• pp.358-366
• /
• 2017

The most important factor in the performances of polymer electrolyte membranes for fuel cells is how fast hydrogen ions can be transported along the water channel formed inside the electrolyte membrane. Since the morphology of the water channel and the diffusivity of the protons are very important factors for the proton transport behavior, various molecular dynamics simulation studies are being carried out to clarify this. The force-field is an important variable parameterizing the movement and interaction of each atom in molecular dynamics simulation. In this study, proton diffusivities of the 3D models of polymer electrolyte membranes were calculated in order to analyze the effects of various types of force-fields on the molecular simulation. It has been found that the charge value determining the non-bonding interaction plays a very important role in the formation of the water channel morphology, and the COMPASS force-field can calculate the accurate proton diffusion behavior. Accordingly, for molecular dynamics simulation of polymer electrolyte membranes, the proper selection of the force-field is very important due to its great effect on the proton diffusion as well as the final molecular structure.

• The korean journal of orthodontics
• /
• v.25 no.5 s.52
• /
• pp.511-523
• /
• 1995

The elastic open activator is one of the modified myodynamic activator. The reduced size of the appliance mass motivates the patients' comfort and longer time of wearing. Its peculiarities in loose fitting and the lack of appliance stabilization in the mouth draws the tongue and the surrounding functional matrices on close interaction with the appliance, consigns the physiologic exertion to target structures, and eventually makes it feasible to the inland of non-extraction treatment In the context of the sagittal malocclusion, the orthodontic trench is dependent upon the growth of basal structure aimed, therefore, it is contemplated to grabble the effects of Elastic Open Activator upon the class II malocclusion of growing child retrospectively. The cephalometric headfilms and study models of nine Class II malocclusion of growing child retrospectively. The cephalometric headfilms and study models of nine class II division 1 and five division 2 patients were evaluated and analyzed, and the following observations were drawn, 1. The maxilla maintained a normal growth pattern in both groups. 2. The mandible grew anteroinferiorly in both groups. 3. The upper incisors tipped ligually in Class II division 1 and tipped labially in Class II division 2 and anterior vertical alveolar growth was interrupted in both groups. 4. The lower incisors tipped labially. 5. There was an arch expansion in both groups and increase of available space in Class II division 2