• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.223-226
• /
• 2007

In the electrical railway, for the improvement of a train speed, it is necessary to study not only the dynamic behaviors of overhead catenary system but the fatigue behaviors of components for a safety assurance according to the increase of vibration level. One of the critical components in the system is a dropper. Therefore, the dynamic force acting on a dropper was measured in the Chungbuk Line and analyzed to figure out the dynamic characteristics the dropper. And in order to assure the safety of dropper clamp and cable, we proposed a test facility as well as test method based on the test results For the further study, we will measure the dynamic forces in the conventional line and high-speed line and make up the test condition, so that the safety of dropper clamps can be assured.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1918-1923
• /
• 2010

In electic railway, 25kV is applied to AC sections of overhead contact lines and pantographs of Korea Train eXpress(KTX) make contact at speeds of 300km/h. Thus, there is a need to utilize wireless, optic, contact-less sensors to implement condition monitoring systems. This paper is based on describing and analyzing the condition monitoring system implementation technologies for efficient catenary current ratio characteristic assessment. The conclusion of this paper should be widely applied to design, diagnosis, completion of construction, current collection status, fault diagnosis, and selection of contact wires and suspension wires.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.864-874
• /
• 2007

Suspension insulator in Catenary Trolley Wire Systems must have two characteristics, electric insulation and mechanical endurance. Because suspension insulator is used in supporting and insulating position between power supply parts and earth conducted supporting parts. The insulator's electric characteristics can be influenced by surface pollution and damage from the environment such as humidity, dust, smoke, salt. etc. And, the insulating parts can be electrically short. These electrically damaged insulator can cause serious accidents that have far-reaching effect. So appropriate management basis of suspension insulator is needed. And we present appropriate cleaning and the changing period of suspension insulator on the basis of actual data.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.3
• /
• pp.281-285
• /
• 2007

Facilities of electric railway should be maintained only at night and it is necessary to maintain by human power because facilities are installed at a high place. This paper presents the development and application of a real-time data acquisition system for the characteristics measurement of overhead contact wires in electric railway. The system is designed to perform in the telemetry environments that developed to store data by wireless in a live wire state of 25 kV power source. The field test results show that the proposed technique and the developed system can be practically applied to measure characteristics of temperature, displacement, and strain on overhead contact lines.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1583-1584
• /
• 2015

최근 철도차량의 고속화와 전력회생을 하는 전기차로 인하여 부하전류와 고장전류 간의 큰 차이가 없으므로 이를 구분할 수 있는 고성능 보호시스템의 중요성이 날로 증대되고 있다. 본 논문은 실계통에서의 전차선로 임피던스를 이용하여 AT급전시스템을 모델링하였으며 변전소와 보조급전구분소사이 단락사고의 과도특성을 분석하였다.

• Proceedings of the KIEE Conference
• /
• 2002.11b
• /
• pp.290-292
• /
• 2002

전기철도 급전계통은 차량 또한 이동 부하이고, 비정상적인 전기적 특성이 나타날 수 있으므로, 전기적으로 정확한 해석을 할 필요가 있다. 본 연구는 PSCAD/EMTDC 과도해석 프로그램을 이용하여 직류 전기 철도 시스템을 모델링 함으로써 전기철도 급전계통의 정확한 특성을 연구하는 것이다. 한전 계통으로부터 전력을 급전 받아 전기철도차량 부하에 공급되는 급전계통을 실제와 가깝게 모델링 함으로써 정상상태 해석과 사고 시 과도특성 분석 및 계통에의 영향 해석을 목적으로 한다. 프로그램 특성상 각각의 소자를 모델링 한 후 4단자망 이론에 근거, 각 소자를 결합하여 전체 계통을 구성한다. 각각의 소자는 전차선로, 정류기 및 제어기를 포함한 차량부 (전동기, 제어소자), 정류 변전소 등으로 구성된다. 이 논문에서는 급전계통의 정상상태 및 고장전류를 분석함으로서 제안된 모델을 검증한다.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.401-403
• /
• 2001

This paper presents an advanced calculation method of permissible current capacity on catenary system. If the permissible current calculation method used in electric power system is applied to electric railroad system, it is troublesome. Because electric load in catenary system varies periodically according to time. Therefore, this study proposes permissible current calculation method through heat equation according to time variation.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1077-1078
• /
• 2006

This paper presents circuit model of catenery in electrified railway system. Most of (a.c.)electrified railway system adopted as AT fed power supply system. This system is fed with twice voltage. It is that AT system can be fed through longer distance. Conventional circuit model of catenary is used T equivalent circuit with lumped parameter. This model may include some problem when traction power supply system is analyzed. In addition, the model with distributed parameter is good for analysis of harmonic and EMI.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1089-1090
• /
• 2006

This paper analyzes impedance convergence characteristics and harmonics of electric locomotives operation and fault condition. To simulate the various fault and operation condition, AT feeding system and various locomotives are modeled using PSCAD/EMTDC. Analysis shows that impedance are converged into protection area in the case of short fault between catenary and rail or catenary and feeder line but in the case of disconnection fault, impedance is rater bigger so protective relay can't detect the fault. Therefore more analysis of overload and high impedance fault caused disconnection fault is needed.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1101-1102
• /
• 2006

In this paper, as a conceptual design of the catenary-current collection run tester which is planning to be constructed by KRRI, the feasibility study is described. In this study, reviews to determine the propulsion linear motor rating based on the target distance-speed curve through various simulation of LSM propulsion system were conducted. Moreover, the reviews of simulation results and desirable linear motor specifications are discussed in this paper.