• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1609-1610
• /
• 2006

이 논문은 인위적으로 전자파를 발생시켜 이 전자파에 의한 반도체 소자의 피해 효과를 조사한 것이다. 동작주파수가 2.45 GHz인 마그네트론으로부터 발생되는 전자파는 끝단이 개방되어있는 도파관을 통해 자유공간으로 전파되고, 도파관 끝단으로부터 $30\;cm\;{\sim}\;50\;cm$인 지점에 반도체 소자들을 위치시켜 동작상태를 확인하였다. 시험에 사용된 피시험체인 반도채 소자로는 TTL과 CMOS 기반기술의 반도체를 사용하였고, LED 구동회로를 구성하여 LED의 점등 여부로 오동작 및 파괴 여부를 육안 식별하였다. 또한 시험 전후의 반도체 소자 표면을 제거 후 칩 상태를 SEM 분석하였다. 시험 결과 도파관 끝단으로부터 50 cm, 40 cm 떨어진 지점에 반도체 소자를 위치시키고 도파관 끝단에서 발생되는 전자파에 의한 반도체 소자의 피해는 전혀 없었다. 그러나 30 cm 떨어진 지점에서 오동작 및 파괴가 일어났다. 오동작 및 파괴가 일어난 시료의 칩 상태를 SEM 분석한 결과 칩 내부의 onchipwire의 용융으로 인한 파괴와 bondingwire의 완전파괴를 확인할 수 있었다. 위의 시험 결과는 인위적인 전자파 환경에서 반도체 소자의 결합 기구를 해석하는 기초 자료로 활용되며, 전자 장비들의 전자파 장해에 대한 이해에 도움이 되는 자료로 활용될 수 있을 것이다.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.133.1-133.1
• /
• 2012

전자파설계는 위성의 전력시스템, 통신시스템 뿐만 아니라 구조체 등 위성시스템 전반에 걸쳐서 종합적으로 고려가 되어야 하며, 이를 위해서는 개발 초기단계에서부터 시스템 설계에 반영되어야 한다. 위성시스템의 상세 설계가 끝난 후에는 시스템에 구현된 전자파 설계의 적합성을 검증하여야 하며 이는 해석 및 시험을 통해 이루어진다. 본 논문에서는 저궤도 중형급 위성이 우주환경에서 전자파적합성을 이루기 위한 설계 기법 및 전자파환경에 대한 적합성 검증과정에 대해서 다루고 있다. 저궤도 중형급 위성시스템에 대하여 구조물의 전자기적 특성을 정의하는 것부터 우주환경에서 위성의 RF호환성에 이르기까지 부품단위에서부터 시스템 수준까지의 전자파 설계 기준과 각 단계별로 전자파적합성을 검증하기 위한 방법 및 절차에 대해서 기술한다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.2
• /
• pp.184-192
• /
• 2001

In this paper, we analyze the result of the conduced emission and susceptibility tests performed on the KOMPSAT-I ETB Platform. The ETB platform consists of the EM (Engineering Model) boxes developed to perform the electrical functional test. During the conducted emission test, we measured the instant waveform in time domain when each switch was turn on, and spectrum of the noise in the frequency range of 10 Hz up to100 MHz fur the steady state of the ETB. During the conducted susceptibility test, no malfunction and no serious damage of the electronic box were observed when a simulated noise waveform was applied to the DC power bus. The simulated waveform was obtained by adding the 6 dB-system margin to the worst case waveform measured from the conducted emission. This test was performed as co-development of the KOMPSAT-I with TRW in USA.

• Defense and Technology
• /
• no.1 s.155
• /
• pp.38-43
• /
• 1992

유도무기는 개발에서 폐기까지 최소한 십년 이상이 소요되는 장기사업이며, 현재 전자파 환경이 급속히 복잡, 강력화 되는 추세일 뿐만아니라 적의 기만전술인 전자파 대항 기법의 발전추세를 비추어 볼때, 실로 장기적인 안목에서 대처해야 할 것이다. 특히 전기기폭장치(EED)의 오작동시 미칠 영향을 고려한다면, 전자파에 대한 안전을 최대한 강구해야함은 물론 상대적으로 낙후되어 있는 전자파 시험평가시설 및 기술의 선진화가 추진되어야 할 것이다

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.9
• /
• pp.831-837
• /
• 2015

Many persons and electronic devices are exposed to electromagnetic (EM) waves generated from magnetic resonance imaging (MRI) equipment, EM pulses (EMPs), and many other kinds of EM wave devices. Finger strips are used to provide shielding from these EM waves. Because of the high thermal conductivity of finger strips, they are used in the design of specialized doors that are installed in shielded rooms. In this study, we perform an accelerated life test using the load acceleration stress, which affects the main failure mode of finger strips. We predict the life of the finger strip under normal usage conditions based on the results of the accelerated life test. We compare the results with those predicted from the life test under normal usage conditions to evaluate the validity of accelerated life testing.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.9
• /
• pp.755-760
• /
• 2013

The electromagnetic compatibility and its effects, and the system design considerations in space environment are studied in this paper using Multipator. The system level EMC test results of digital channel amplifier(DCAMP), its affects upon the H/W improving methods regarding its over exceed value of EMC specification are discussed. These analysis values and test results can be used as the criteria for the selection of EMC requirements and of the MILSATCOM system design.

• Aerospace Engineering and Technology
• /
• v.5 no.2
• /
• pp.67-76
• /
• 2006

This paper describes the analysis method to define the system specification for conducted EMI environment and verification method to evaluate the conducted EMI performance. Conducted EMI environment is characterized by the electrical power subsystem which is mainly issued by the switching circuit noise, common ground impedance coupling. To define and control these EMI problems, EMI assesment through system analysis are preceded at the early design phase and then EMI reduction methods are applied during the unit/system development phase. System EMC should be carefully controlled and designed in the consideration of EMC safety margin and its performance is fully evaluated at the whole development period.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.4
• /
• pp.492-498
• /
• 2021

In this paper, the electromagnetic wave transmittance of the reinforced concrete structure wall was analyzed using the performance measurement system of electromagnetic wave shielding. Recently, electromagnetic wave shielding technologies on the reinforced concrete wall conditions have been studied, and the shielding effectiveness have been tested on unit cell size. However, the unit cell size tests have problems on that the measurement range for shielding performance is insufficient and it is difficult to reflect the real conditions of the concrete wall. Therefore, we constructed a shielding performance measurement system using a large sample of 2.2m × 2.2m like a real wall. To verify the measurement system, general reinforced concrete test samples were selected, and real shielding performance measurements and numerical analysis were proceeded. Test and numerical analysis results showed similar tendencies in the evaluation frequency range of 75MHz to 2GHz. Thus we validated the effectiveness of this shielding performance measurement system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.7 no.1
• /
• pp.36-42
• /
• 1996

In general, EMI(electromagnetic interference) from EHV(extra high voltage) power lines above 50kV cause interference to AM radio and low VHF television reception. This paper describes the results of long-term measurement of RI and TV1 in 765kV, double circule of $6\times29.59mm$(1.65k inches) diammer $480mm^{2}$(Rail) ACSR conductors in suitable for 766kV transmission lines to provide acceptable EMI at 15m fro the beneath of outmost phase.

• Aerospace Engineering and Technology
• /
• v.6 no.1
• /
• pp.222-229
• /
• 2007

Environmental tests should be carried out to show that design performance is in an operational condition in an actual operational environment to assure maintainability and reliability. Aero-products electromagnetic compatibility tests are performed mainly for the individual parts and Specifications MIL-STD-461E and RTCA DO-160E are developed for the military and commercial parts tests respectively. The MIL-STD-461E which is a military environmental test standard is targeting all munitions and that user can apply by selecting applicable requirements from this specification. On the other hand, requirements are applied exclusively for the Avionics Equipments in commercial test standard.