• Composites Research
• /
• v.21 no.1
• /
• pp.40-45
• /
• 2008

Rubber hose assembly for automotive hydraulic brake during operation is subject to combined stresses of cyclic pressure, cyclic bending and torsion as well as thermal load. The rubber hose is composed of ethylene-propylene diene monomer(EPDM) rubber layers reinforced by polyvinyl acetate(PVA) braided fabrics. A durability tester with loading rigs for inducing the above cyclic stresses was used to investigate failure mechanisms in the rubber hose assembly. Failure examination was performed at every 100 thousands cycles of bending and torsion. Hose samples were sectioned with a diamond-wheel cutter and then polished. The polished surface was observed by optical microscope and scanning electron microscope (SEM). Some interfacial delamination with a length of about 1mm along the interface between EPDM rubber and PVA fabrics was shown at the test cycles of 400,000. The delamination induced some cracking into the outer rubber skin layer to leading the final rupture of the hose.

• Journal of Drive and Control
• /
• v.4 no.1
• /
• pp.2-8
• /
• 2007

• Information and Communications Magazine
• /
• v.34 no.5
• /
• pp.19-26
• /
• 2017

Electromechanical Brake(EMB)시스템은 유압 대신 전동식 액츄에이터를 이용하여 제동력을 발생시키는 브레이크 장치인 Brake-by-Wire(BBW) 시스템의 구성요소 이다. EMB 시스템은 기존 유압식 브레이크 시스템과 비교하여 친환경적이며, 설계의 자유도가 높고, 제동 응답성 및 제어 성능이 뛰어난 장점을 가진다. 하지만 전자 전기적으로 시스템 구성이 복잡해 짐에 따라 고장에 대한 안정성 부문이 설계시 충분히 고려되어야 한다. 본 논문에서는 차량 EMB 시스템 설계시 신뢰성을 향상을 위해 고려해야 설계 방안에 대해서 기술한다. 크게 시스템, 센서, 모터 분야에 대해 고장 요소 및 대처 방안 설계에 대해 개괄적으로 소개한다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.4
• /
• pp.599-606
• /
• 2017

In this paper, the automatic control system of the stroller brake was designed and manufactured to reduce the safety accident of the stroller. The ultrasonic sensors are used to determine whether the handle of the driver's hand is touching or not, and the gyro sensor is designed to detect the current tilt of the baby carriage. If the next driver's hand is not recognized and the tilt exceeds a certain angle, the servo motor is activated and the hydraulic brake is operated to prevent the accident on the downhill road. Finally, in this paper, a smart phone-based application was developed to make the remote control of the brake possible.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.539-540
• /
• 2011

본 논문에서는 건설기계 및 운반기계, 차량의 유압장치(브레이크, 클러치 및 파워 스티어링 시스템)로 널리 사용되어지고 있는 외접기어펌프의 치형을 Involute 기어형식으로 설계하였다. 상용프로그램인 Pumplinx 프로그램을 통해 이 기어를 해석하여 효율 및 성능을 알아보았다.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1576-1577
• /
• 2007

As a intelligent valve piezoelectric valve is to applied to various fields of application. Piezoelectric valves have fast response time and good linearity for pressure control but its hysteresis displacement by its stack actuator influences on pressure control in electro-hydraulic braking. Solenoid valves are traditional element to control hydraulic pressure but this paper proposes piezoelectric valve for brake pressure control with hysteresis compensation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.4
• /
• pp.335-341
• /
• 2010

The electric braking system obtains its braking force by a motor instead of the hydraulic brake which has been used in conventional automobile systems. Electric braking system is consisted of fewer numbers of components than hydraulic braking system, and it has effects of improved response and reduced braking distance for the ABS(Anti-lock Brake System) and ESC(Electronic Stability Control). This paper presents the BLAC motor drive system for Electro-Magnetic Brake(EMB). Proposed control system consists of the power converter for driving a motor and the digital control system for speed control, and the vector control is applied for fast torque response. It is verified through the simulation using Matlab/Simulink and experiment that the proposed BLAC drive system can be applied to EMB.

• Journal of Drive and Control
• /
• v.16 no.2
• /
• pp.36-42
• /
• 2019

The ESP (Electronic Stability Program) is an active control system that controls the posture of the vehicle by sensing the unstable state of the vehicle during braking, driving, or turning. The system works if the vehicle becomes unstable and it is very dangerous to develop it in the actual vehicle. For this reason, many studies have been carried out on the method of developing with simulation such as SIL / EIL. Some advanced companies have already applied it to the product development process. In this study, ESP hydraulic system and braking device model were constructed using SimulationX to build ESP SIL / EIL model. The hydraulic system model was constructed using the actual design parameters and the performance of the hydraulic model was verified by comparing with the actual vehicle test.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.7 no.2
• /
• pp.7-12
• /
• 2010

In these days, the researches about hybrid and fuel cell electric vehicles are actively performed due to the environmental contamination and resource exhaust. Specially, the technology of regenerative braking, converting heat energy to electric energy, is one of the most effective technologies to improve fuel economy. This paper developed a regenerative braking control algorithm that is considered vehicle stability. The vehicle has a inline motor at front drive shaft and has a EHB(Electo-hydraulic Brake) system. The control logic and regenerative braking control algorithm are analyzed by MATLAB/Simulink. The vehicle model is carried out by CarSim and the driving simulation is performed by using co-simulation of CarSim and MATLAB/Simulink. From the simulation results, a regenerative braking control algorithm is verified to improve the vehicle stability as well as fuel economy.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.3
• /
• pp.166-174
• /
• 2000

Anchovy, EngrauEis japonica scoop nets are used in the coastal of Southern and Cheju of Korea. Especially in the Cheju, the fishing gear of scoop nets consists of upper boom, lower boom, pressing stick and bag net. They are operated by fishing boats of 6 to 10 ton class and 8 persons on board. The booms are controlled by side drum, and the net and pressing stick are hauled by only human power in operating. Therefore this fishery needs to large labor and heavy human power and has much risk. Three kinds of hydraulic winding device which controls two booms was designed and manufactured to reduce heavy labor force of scoop nets, and trial in the sea was carried out to test their performances using the commercial fishing boats of 6 ton class. The proper capacity of hydraulic pump and motor were determined by model test of boom 1/5 scale. The results obtained are as follows, 1. Tension of boom which is being drawn was the strongest and 187.5kgf when the boom's end is in the depth of 4m under the water. 2. The hydraulic motor of the fittest kind of winder has the least leakage per time than the other kinds. 3. In the best type of several winder devices, when the pressure difference was fixed $130kg/^2$ for the safe fishery, the winding velocity of boom line was 2m/sec, is faster 0.48/sec than traditional fishing method and this winder can catch the anchovy of 1.6 tonnage. 4. As a result, the crew were decreased from 8 to 6 and the problem of heavy human power and risk on fishing operation were solved by using the this winder.