• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.331-334
• /
• 2003

This letter presents the design and measured performance of bandpass filters based on a stacked-SIR (stepped impedance resonators) configuration with DGS (Defected Ground Structure). An unit DGS configuration is designed and analyzed to show the phase characteristic of proposed slow-wave structure. The SIR filter with DGS has been yielded better stop band and sharper skirt behavior than conventional bandpass filter.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.313-316
• /
• 2003

The LTCC bandpass filter using multilayer resonators is made of combline type and interdigital type parallel coupled-lines. The equivalent circuits of parallel coupled-lines are analysed. They are applied to make an equivalent circuit of LTCC bandpass filter using multilayer resonators. The 3-pole bandpass filter of the center frequency of 2.45GHz with 200Hz bandwidth is designed and fabricated. The simulated result of the bandpass filter are presented.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.12
• /
• pp.7-11
• /
• 2007

In this paper, we proposed the dual-mode stepped impedance ring resonator bandpass filter for MMIC (Microwave Monolithic Integrated Circuit) applications using the dielectric-supported air-gapped microstrip line (DAML). The ring resonator fabricated by surface micromachining technology. This filter consists of a DAML resonator layer and a CPW feed line. The DAML ring resonator is elevated with $10{\mu}m$ height from GaAs substrate surface. This bandpass filter is $1-{\lambda}g$ type stepped impedance ring resonator including dual-mode resonance. From the measurements, we obtained attenuation of over 15 dB and insertion loss of 2.65 dB at the center frequency of 97 GHz. Relative bandwidth is about 12 % at 97 GHz. Furthermore, the proposed bandpass filter is useful to integrate with conventional MMICs.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.2 no.4
• /
• pp.59-64
• /
• 2009

In this paper, we represent characteristics and equivalent circuit of donut type resonator of defected ground structure (DGS), and can control resonant frequency with chip capacitor. In General, DGS operates like with parallel LC resonator. We found out variation of resonance frequency when capacitor is placed on slot of DGS. If the chip capacitor replace with varactor diode, the resonance frequencies can be controlled by voltage. This tualable resonator can apply to voltage controlled oscillator and tunable bandpass filter.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.36S no.10
• /
• pp.10-20
• /
• 1999

In this paper, we propose and analyze a multiuser receiver using a decorrelating filter and Viterbi decoders for trellis coded DS/CDMA systems with biorthgonal signal constellation in asynchronous channels. The biorthogonality is implemented by user signature waveforms and the decorrelating filter. The performance of the proposed system is investigated with emphasis on the asymptotic cases. It is shown that the proposed system can provide us with some coding gain and near-far resistance. We also analyze the performance of the proposed system with base-station antenna array.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.260-264
• /
• 2003

In this paper, a $\lambda/4$ hairpin resonator is proposed to reduce the size of planar resonators for a LTCC MLC bandpass filter. The $\lambda/4$ hairpin resonator operates as stepped impedance resonator (SIR) without changing the width of the planar resonator. It is composed of two sections those are parallel coupled line and transmission line. The characteristic impedance of two sections is different each other. The design formulas of the bandpass filter using the coupling element at the arbitrary position are derived from even and odd-mode analysis. The formulas can take account of the arbitrary coupling of lumped ana/or distributed resonators. The advantage of this filter is its abilities to change freely the coupling structure between two resonators. Experimental bandpass filters for 2.4GHz Band are implemented and their performances are shown.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.317-322
• /
• 2003

In this paper, we design a slow-wave bandpass filter that uses a microstrip line periodically loaded with microstrip ing resonators for WLAN(5 GHz). Unlike conventional slow-wave filters, this filter is designed to produce a narrow passband at the fundamental mode of the resonators and provide lower insertion loss than that of parallel- or cross-coupled ring bandpass filters. A PBG(Photonic Band Gap) structure patterned in the ground plane is used to suppress the spurious transmission and extend out-of-band rejections Experimental result shows that the first spurious response in the stopband of the slow-wave bandpass filter can be rejected using a PBG structure.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.5
• /
• pp.616-624
• /
• 1986

In this paper, we propose an accurate design method of E-plane type filters using the synthesis procedures and the passband correction factor. This correction factor is obtained from the actual insertion losses of the pre-designed filter at band edge frequencies. For this study a CAD program has been developed. In this program, the Fin-line structures are analyzed by the variational analysis routines. Unilateral Fin-line filters and bilateral Fin-line filters are fabricated in the X-band. Experimental results show excellent agreement with the theory.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.6
• /
• pp.8-12
• /
• 2008

A ring resonator based band-pass filter enabling enhanced sideband suppression was proposed and demonstrated. It is composed of a single-ring based band-pass section combined with a band-rejection section based on two different coupled rings. The sideband region of the transfer characteristics of the first band-pass filter section was selectively suppressed by means of the band-rejection section without causing any excessive insertion loss. As a result, the overall transfer characteristics of the proposed filter was unproved so that its sideband suppression was elevated to allow for sharper roll-off and narrower bandwidth. In this work, a conventional single-ring band-pass filter and a proposed filter including the band-rejection section were designed and fabricated. As for the achieved device performance, with the center frequency at about 4 GHz, the sideband suppression ratio was increased as much as 8 dB and the 3-dB bandwidth was reduced from 98 MHz to 48 MHz by about 51% with no remarkable excessive insertion loss as expected. And the quality factor of the device was increased by about 105%.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.8
• /
• pp.1-7
• /
• 2007

Class AB bipolar linear transconductors for high frequency applications ire proposed. They consist of a voltage follower, a resistor, and a current follower. The follower circuits are realized by translinear cells or unity-gain buffers. The proposed transconductors are simulated using an 8 GHz bipolar transistor-arrary parameter. Simulation results show that the transconductor using translinear cells has better linearity than one using unity-gain buffers whereas the latter has better temperature stability and higher input resistance than the former. In order to test their high frequency applicability, the transconductors are used to implement an 4th order IF bandpass filter.