• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.828-830
• /
• 2001

잘 교정된 유도성 전압 분할기는 다른 교류 전압 분할기들을 비교 교정하기 위한 전압비의 표준기로서 사용되어질 뿐 만 아니라 각종 임피던스 정밀측정용 브리지의 비례 arm으로서 사용이 되어진다. 이러한 유도성 전압 분할기를 비교교정 하기 위한 교정시스템이 연구제작이 되었다. 본 연구 논문에서는 제작방법, 교정방법, 그리고 오차 등에 대하여 관하여 논의하고 실제교정결과와 분석된 결과를 비교한다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.921-926
• /
• 1998

CANFLEX 연료봉 다발의 3000 시간 내구성 시험 기간 동안 속도센서를 사용하여 압력관 내부에 장전된 연료봉 다발의 진동을 측정하였다. 압력관 내부에 장전된 연료봉의 진동측정은 고온, 고압, 그리고 공간적 제약 때문에 가속도계나 스트레인 게이지 같은 접촉센서로는 측정할 수 없다. 비접촉 센서를 사용하면 이러한 난점을 해결하고 압력관 내부에 장전된 연료봉 다발의 진동을 측정할 수 있다. 속도센서는 비접촉 센서로서 가우스(gauss)의 크기를 감지하여 전압을 출력하는 센서이지만, 측정거리, 주파수, 그리고 속도와 가우스가 비선형이기 때문에 교정을 한 후에 사용하여야 한다. 본 본문에는 속도센서의 교정방법과 압력관 내부에 고온, 고압의 유체가 흐를 때 발생하는 연료봉 다발의 진동특성을 구하였다.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.5
• /
• pp.217-221
• /
• 2005

A inductive voltage divider(IVD) is widely used as a ratio arm of precise impedance measurement bridges at low frequencies of audio frequency range and a well fabricated IVD has ratio error of $10^{-7}$ order without any calibration. Recently, the order of $10^{-8}$ of the best measurement uncertainty is needed for calibration and maintenance of impedance standards as national standards. In order to achieve that uncertainty, the IVD which is used for a ratio arm of precise impedance measurement bridge should be calibrated within the uncertain of order of $10^{-8}$ For this purpose, a ratio calibration bridge for IVDs has been developed. The measurement uncertainties of both inphase and quadrature of the bridge are analyzed less then $3{\times}10^{-8}$ respectively at 1 kHz and 25 V.

• Journal of Sensor Science and Technology
• /
• v.5 no.3
• /
• pp.9-16
• /
• 1996

This paper deals with the capacitive voltage divider which can measure a transient voltages generated by operating a high voltage impulse generator. The transient voltage measuring system using the capacitive electric field sensor consists of the planar-type electric field sensor having a fast response characteristic and the wide-bandwidth voltage follower, and the input impedance of which is extremely high, about $10^{12}{\Omega}$. In order to analyze the response characteristics to a step input, the newly developed calibration method is proposed, and the error of voltage dividing ratio associated with set-up condition is investigated. Also the optimal set-up condition that is to be maintained within the range of 0.5 % is taken. From the calibration experiment, the frequency bandwidth of the transient voltage measuring system whose response time to a step input is about 15.8 ns, is from 6.37 Hz to 27.3 MHz. Therefore it is possible to measure the commercial frequency voltages as well as the transient over voltages without signal distortions.

• Journal of Sensor Science and Technology
• /
• v.7 no.4
• /
• pp.293-299
• /
• 1998

An objective of this study is to develop a voltage measuring device that uses a gas-filled switch (GS) on 22.9 kV-y extra-high voltage distribution lines. The voltage measuring device proposed in this paper is a kind of capacitive divider which consists of a detecting electrode attached outside of the bushing of GS, an impedance matching circuit, and a voltage buffer. It can be easily installed in an established GS without changing the structure. For the calibration and application investigations, the voltage measuring device was set up in the 25.8 kV 400 A GS, and a step pulse generator having 5 ns rise time is used. As a result, it was found that the frequency bandwidth of the voltage measuring device ranges from 1.35 Hz to about 13 MHz. The error of voltage dividing ratio which is evaluated by the commercial frequency voltage of 60 Hz was less than 0.2%. In addition, voltage dividing ratio in the commercial frequency voltage and in a non-oscillating impulse voltage were compared, and their deviation were less than 0.7%.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1612-1615
• /
• 2001

포항 방사광 가속기 2.5 GeV의 전자선형 가속기는 마이크로웨이브 발생원으로써 80 MW 클라이스트론(klystron) 11대와 입사부에 65 MW 클라이스 트론 1대를 사용한다. 전자빔 에너지의 효율적인 제어를 위하여 고출력 클라이스트론의 RF 전력과 입력 빔의 전력을 정확하게 측정해야 하며 응답특성이 양호한 측정장치와 정밀한 측정이 요구된다. 클라이스트론에 공급되는 전력은 캐소드에 인가되는 전압과 전류의 측정치로 계산된다. 비록 빔 전압측정에서의 작은 오차일지라도 클라이스트론 RF 출력 전력의 결과값에 큰 영향을 미친다. 따라서, 빔 전압의 측정시에 정확한 측정을 위하여 특별한 주의가 요구된다. 고전압 펄스전원장치 인 모듈레이터 (modulator)에서 발생되는 수백 kV(350-400 kV)의 전압을 측정하기 위하여 커패시터의 용량비로 입력전압을 분압하는 용량성 분압기(capacitive voltage divider, CVD)가 사용된다. 고압측 분압용 표준 콘덴서의 정전용량을 결정하는 주요인자는 고전압 절연유의 유전율(dielectric constant)이다. 그러므로, 측정범위 내의 전압, 주파수, 온도에 대하여 정전용량의 변화율이 작도록 설계하여야 한다. 본 논문에서는 펄스형 고전압 신호 측정을 위한 용량성 전압 분배기의 측정원리, 설계분석, 교정시험, 절연유의 온도변화에 따른 정전용량 변화 특성에 대한 실험 결과를 고찰하고자 한다.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.12
• /
• pp.109-117
• /
• 2015

In this paper, we proposed error-reducing method to source or measure a current or voltage for LED in the I-V characteristic analysis system using a digital signal processor (DSP). this method has the advantage of reducing a non-linear circuit error and random error. random error can be reduced using recursive averaging technique and non-linear circuit error can be reduced using 2rd polynomial regression calibration parameters fitting with measured sample data. it corrects measured error of IR, VR, VF1, VF2, VF3 of LED using calibration parameters. experimental results show that can be performed with about 0.017~0.043% accuracy.

• Nuclear Engineering and Technology
• /
• v.10 no.3
• /
• pp.137-144
• /
• 1978

A method is presented here in order to determine a nonlinearity correction of observed counter rates in a GM counter. An expression, which is developed under the assumption of dead time dependence on counting rates, gives good agreement with the results obtained from the experimental work. The variation of pulse voltages from a GM counter with counting rates was measured with the aid of pulse height analyzer. This method gives accurate values for the dead time over a wide range of counting. The technique as outlined allows tile exact correction of the nonlinearity caused by dead time loss. It was observed that the dead time decreases as the counting rate increases.

• The korean journal of orthodontics
• /
• v.30 no.2 s.79
• /
• pp.197-204
• /
• 2000

[$K^+$]-selective ion channels were studied in excised inside-out membrane patches from human osteoblast-like cells (G292). Three classes of $K^+$channels were present and could be distinguished on the basis of conductance. Conductances were $270\pm27\;pS,\;113\pm12\;pS,\;48\pm8\;pS$ according to their approximate conductances in symmetrical 140 mM KCl saline at holding potential of -80 mV It was found that the small conductance (48 pS) $K^+$channel activation was dependent on membrane voltage. In current-voltage relationship, small conductance $K^+$channel showed outward rectification, and it was activated by the positive potential inside the membrane. In recordings, single channel currents were activayed by a negative pressure outside the membrane. The membrane pressure increased $P_{open}$ of the $K^+$ channel in a pressure-dependent manner. In the excised-patch clamp recordings, G292 osteoblast-like cells have been shown to contain three types of $K^+$ channels. Only the small conductance (48 pS) $K^+$channel is sensitive to the membrane stretch. These findings suggest that a hyperpolarizing current, mediated in part by this channel, may be associated with early events during the mechanical loading of the osteoblast. In G292 osteoblast-like cells, $K^+$channel is sensitive to membrane tension, and may represent a unique adaptation of the bone cell membrane to mechanical stress.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.5
• /
• pp.305-308
• /
• 2004

The 7-dial inductive voltage divider(IVD) for application at low frequency range which can precisely divide the in put voltage up to resolution of $10^{-7}$ was fabricated by using the toroidal cores made by super-mumetal strips of 0.025 mm thick and special decade switches. The cores have the initial permeability of 200.000 and magnetic flux density of 0.5 T. The inphase and quadrature ratio errors for a fabricated 7-dial IVD are found to be less than $\pm$4${\times}$$10^{-7}$ and $\pm$5${\times}$$10^{-6}$ rad(k=2), respectively. by calibration using the IVD calibration system of KRISS. The fabrication techniques used and uncertainty evaluation are discussed in this paper.