• The Korean Journal of Rheology
• /
• v.5 no.2
• /
• pp.99-108
• /
• 1993

시멘트 페이스트의 비선형적 점탄성 거동을 연구하기 위해 동적인 전단 유동 시험 이 수행되었다. 전단응력과 전단변형 또는 전단변형율간의 관계를 보여주는 히스테리시스 곡선을 얻기 위하여 전단응력이 연속적으로 측정되었다. 이는 기존의 주파수 혹은 변형의 증가에 의한 실험(frequency or strain sweep experiment)과는 달리 저자에 의해 수정된 점 성계(HAAKE Model RV20/RC20/CV20N)의 조정프로그램을 이용하여 수행되었다. 동적 전 단유동시험에서 얻어진 히스테리시스곡선은 시멘트 페이스트가 전단변형을 받는 동안 선형 탄성, 입자간 연결고리의 파괴 및 점성유체 거동을 보여준다. 측정된 항복전단응력은 전단변 형율의 증가에 따라 파우어함수(Power low equation)에 의해 증가함을 보여준다.

• Ecology and Resilient Infrastructure
• /
• v.5 no.4
• /
• pp.199-209
• /
• 2018

In river design, consideration of bed shear stresses is necessary to secure stability of levee and floodplain. In this study distributions of bed shear stresses in compound open channels are analyzed through numerical simulation for various width and depth. LES solver in OpenFOAM is applied to 12 cases of compound channel shapes considering secondary flow which effects distributions of bed shear stresses. By the results time averaged velocity distributions, secondary currents, and distributions of bed shear stresses are analyzed. Overall distributions of bed shears in floodplain show that higher shear stresses are seen in left of floodplain and the shears decrease toward right of floodplain. However, high local variations in shear stresses are shown due to the secondary flow effects. In shallow floodplain, bed shear stresses show low value below 0.8 times of averaged bed shear. In deep floodplain, bed shear stresses show high value over 1.2 - 1.4 times of averaged bed shear.

• Tunnel and Underground Space
• /
• v.13 no.3
• /
• pp.169-179
• /
• 2003

Anisotropic shear strength of rock joints is studied based on the artificially fractured specimens using experimental and analytical methods. Series of direct shear tests are performed to obtain the strength, stiffness and friction angle of joints under various low normal stresses and shearing directions. The results of shear strength and stiffness show anisotropic value according to shearing direction under low normal stress specially less than 2.45 MPa. But, the effect of joint roughness on strength decreases with increasing normal stress. To estimate more effectively the peak shear strength under low normal stress, the modified Barton's equation is suggested.

• Tunnel and Underground Space
• /
• v.17 no.3 s.68
• /
• pp.186-196
• /
• 2007

In this study, direct shear tests were carried out on the 30 rock joint samples in order to investigate the influence of roughness and normal stress on the shear behaviour. Joint roughness profiles were measured by use of 3D laser profiler, and then the samples were equally classified into three individual groups according to the roughness index of rock joints. Peak shear strength, residual shear strength, shear stiffness, dilation angle of rock joints were investigated in condition of five different constant normal load. Peak shear strength was increased as roughness index was increased, and the influence of roughness on strength was found to be more considerable in case of lower normal stress condition. Residual shear strength and shear stiffness were increased as roughness index and normal stress were increased. Finally dilation angle was decreased as normal stress was increased, but it was increased as roughness index was increased in the same normal stress condition.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.1C
• /
• pp.53-62
• /
• 2008

A constitutive model, which can simulate the effect of principal stress rotation associated with direct simple shear test, is proposed in this study. The model is based on two mobilized planes. The plastic strains occur from the two mobilized planes, and depend on stress state, and they are added. The first plane is a plane of maximum shear stress, which rotates about the horizontal axis, and the second plane is a horizontal plane which is spatially fixed. The second plane is used to consider the effect of principal stress rotation on simple shear tests under different stress states. The soil skeleton behavior observed in drained simple shear tests is captured in the model. This constitutive model is incorporated into the dynamic coupled stress-flow finite difference program FLAC. The model is first calibrated with drained simple shear tests on loose Fraser River sand. The measured shear stress and volume change are partially induced by principal stress rotation and compared with model calculations. The model is verified by comparing predicted and measured settlements due to rigid footing resting on loose sands. Settlements predicted by the proposed model were very similar to measured settlements. Mohr-Coulomb model can not consider the effect of principal stress rotation and its prediction was only 20% of measured settlements.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.41-41
• /
• 2015

하천의 지형을 조사하고 계측하는 것은 하천을 연구하는 전문가들에게 필수적인 일이다. 하지만 하천의 지형을 계측하는 것은 쉽지 않으며, 조사를 하여도 유사의 이송으로 인하여 하천의 지형은 시간이 지남에 따라 변하게 된다. 그러므로 실험이나 모델링을 통하여 하천의 지형을 예측하고 모의하는 것은 중요한 연구이다. 모델링을 이용하여 유사이송에 의한 하상변동을 잘 예측하기 위해서는 하천의 복잡한 흐름을 정확히 모의하는 것이 중요하며 유사를 발생시키는 힘인 하상전단응력을 정확히 산정하는 것 또한 중요하다. 하상의 전단응력을 산정하는 방법으로는 대표적으로 로그법칙에 의한 방법, 레이놀즈응력 분포를 이용한 방법, 난류운동에너지를 이용한 방법 등이 있다. 앞서 말한 방법으로 산정된 전단응력 값은 차이를 보이며, 이는 하상변동을 정확히 모의하는 것에 문제를 발생시킬 수 있다. 따라서 본 연구에서는 곡선좌표계를 이용하여 3차원 유동 및 하상변동을 모의할 수 있는 수치모형을 이용하여 전단응력 산정 방법에 따른 하상변동량을 분석하는 것이다. 하천의 복잡한 흐름을 정확히 모의하기 위하여 본 연구에서는 RANS (Reynolds Averaged Navier-Stokes) 방정식을 3차원으로 해석하여 흐름 계산을 하였고 유사량 산정공식과 Exner 방정식을 이용하여 유사이송에 의한 하상변동을 계산하였다. 흐름 계산의 검증을 위하여 선행 연구의 실험을 대상으로 모의하였다. 그리고 곡선으로 된 실험 수로를 대상으로 전단응력 산

• Journal of the Korean Geotechnical Society
• /
• v.31 no.9
• /
• pp.17-27
• /
• 2015

We perform a series of experimental tests to evaluate whether the shear strength of clean sands can be reliably predicted from shear wave velocity. Isotropic drained triaxial tests on clean sands reconstituted at different relative densities are performed to measure the shear strength and bender elements are used to measure the shear wave velocity. Laboratory tests reveal that a correlation between shear wave velocity, void ratio, and confining pressure can be made. The correlation can be used to determine the void ratio from measured shear wave velocity, from which the shear strength is predicted. We also show that a unique relationship exists between maximum shear modulus and effective axial stress at failure. The accuracy of the equation can be enhanced by including the normalized confining pressure in the equation. Comparisons between measured and predicted effective friction angle demonstrate that the proposed equation can accurately predict the internal friction angle of granular soils, accounting for the effect of the relative density, from shear wave velocity.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.10
• /
• pp.151-163
• /
• 2006

This paper presents the interrelationship between undrained static and cyclic shear behavior. Laboratory works were performed through the undralned static and cyclic triaxial test using Nak-Dong River sand. And static triaxial test involved the triaxial extension test for comparison with cyclic shear behavior Cyclic triaxial test was performed with a variety of combination conditions of initial static shear stress $(q_{st})$ and cyclic stress $(q_{cy})$. In this result, the stress path of cyclic shear behavior was correspondent with static shear behavior passing the critical stress ratio (CSR) line because of the development of flow deformation. After that, a failure occurred according to failure line (FL) of static shear behavior. The stress path of cyclic shear behavior showed essentially the same with static shear behavior, although it appears a little different in test method.

• Tunnel and Underground Space
• /
• v.17 no.3 s.68
• /
• pp.203-215
• /
• 2007

Stability and mechanical deformation behavior of rock masses are highly dependent on the mechanical characteristics of contained discontinuities. Therefore, mechanical characteristics of the discontinuities should be considered in the design of tunnel and underground structures. In this study, direct shear tests for rough granite joints were carried out under constant normal stiffness conditions. Effects of initial normal stress, shear velocity, and surface roughness on the characteristics of shear strength and deformation behaviors were examined. Results of shear testing under constant normal stiffness conditions reveal that shear behaviors could be classified into two categories, based on the amount of decrease in shear stress at the Int peak shear stress. With initial normal stiffness increasing, it turned out that shear displacement at peak stress and the first peak shear stress increased, however friction angle and friction coefficient showed decrease. In case of shear stiffness and average friction coefficient, it turned out that they are not dependent on the initial normal stress. Minor effects of shear velocity on rough joints were observed in several shear quantities. However, the effects of shear velocity were insignificant regardless of the normal stress increase. Change of shear strength and deformation characteristics on joint roughness were examined, however, it turned out that the variations were attributed to deviation of shear test specimens.

• Journal of Wetlands Research
• /
• v.19 no.2
• /
• pp.202-210
• /
• 2017

Shear stress is one of the most important mechanical factors used in various fields and is important for the design of artificial channels. Current shear stresses have been used in the past, but there are factors that are difficult to actually measure or calculate, such as bed shear stress and energy slope in the equation used. In particular, the energy slope is a very difficult factor to estimate, and it is difficult to estimate the slope and flow velocity of the boundary layer although the energy slope can be used to obtain the shear stress distribution. In addition, the bed shear stress among the shear stress distribution is very difficult to measure directly, and the research is somewhat slower than the velocity. In this study, we have studied the simple calculation of the average flow velocity and the shear stress distribution using entropy M without reflecting the energy gradient, and we used existing laboratory data to demonstrate the utility of the applied equation. The stress distribution in the graphs was comparatively analyzed. In the case of the uniform flow and the non-uniform flow, the correlation coefficient was almost identical to 0.930-0.998.