• Journal of the Korean GEO-environmental Society
• /
• v.23 no.12
• /
• pp.25-31
• /
• 2022

Unlike structures installed on land, the structures installed on the offshore ground must consider long-term cyclic loads such as wave loads, wind loads and tidal loads at sea. Therefore, it is important to analyze the behavior of the ground subjected to long-term cyclic loads in order to design a structure installed on the ocean ground. In this paper, cyclic simple shear tests were performed to analyze the ground behavior for long-term cyclic loads according to the confining pressure, and a three-dimensional design failure curve was prepared that can easily check the failure characteristics according to the confining pressure. As a result of the analysis, it was confirmed that the position of the design failure curve is different depending on the confining pressure even under the same conditions of the cyclic shear stress ratio and the average shear stress ratio, and the number of cyclic loads reaching failure is affected by the confining pressure. From the created 3-D design failure curve under different confining pressure, the tendency and approximate value of the design failure curve according to the confining pressure can be estimated.

• Korean Journal of Materials Research
• /
• v.6 no.9
• /
• pp.963-971
• /
• 1996

세라믹 강화 복합 재료의 모재로서 사용되는 무정형 PEEK가 보여주는 self-bonding 현상의 주 기구인 PEEK체인들의 확산(interdiffusion)과 뒤엉킴(entanglement)이 일어나기 위하여 PEEK의 접합 면에서 반드시 선행되어 일어나야 하는 젖음성의 정도에 미치는 접합 공정 변수의 영향을 C-mode acoustic microscopy를 이용하여 고찰하였다. 또한 self-bonding 된 PEEK시편들의 전단 변형시 전단 하중의 증가에 따라 일어나는 접합 면에서의 debonding 정도를 측정함으로써 접합 면에서 일어나는 파괴 거동을 관찰하였다. 각각의 접합 조건에서의 젖음성의 정도는 시간과 압력의 증가에 따라 다소 증가함을 보여 주었으나, 접합 온도와는 거의 무관함을 보여 주었다. 또한 전단 파괴 시험시 각각의 접합 조건 하에서 개발된 self-bonding강도의 80%-90%이상의 전단 하중이 가해진 후부터 debonding이 시작되어, 이 후 하중이 증가함에 따라 급속도로 진행되어 파괴가 일어남을 알 수 있었다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.3
• /
• pp.130-137
• /
• 2017

The purpose of this study is to provide a reasonable analytical method for the reinforced concrete beams which shows failure mode of shear and flexure-shear by proposing a modified formulation to consider the effect of shear deformation on the beam-column fiber element based on the flexibility method and a new constitutive law of inelastic shear response history for the section. A total of 6 specimens of reinforced concrete beams which is designed to cause shear failure before yielding longitudinal reinforcement to investigate the influence of the main experimental variables on the shear behavior characteristics and the analysis was performed by using a non-linear finite element analysis program (RCAHEST) applying the newly modified constitutive equation by the authors. The failure mode and the overall behavior characteristics until fracture are predicted appropriately for all specimens and the results are expected to be useful enough for the 3 - D analysis to carry out reliable results of large-scale and complicated structures in the future.

• Magazine of the Korea Concrete Institute
• /
• v.14 no.2
• /
• pp.30-36
• /
• 2002

콘크리트가 화재에 노출될 경우 가열에 의한 재질의 노화 및 열팽창에 의한 열응력의 발생에 따라 주요구조부인 기둥 및 보에 큰 손상이 생기게 되어 그 내력은 크게 저하하게 된다. 철근 콘크리트 구조물의 화재 상황을 조사해 보면 (그림 1)과 같이 열응력에 의한 기둥의 전단파괴, 보의 휨파괴 및 부재의 폭열 등이 보여진다.(중략)

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1A
• /
• pp.107-115
• /
• 2006

A challenging topic was and still is the failure behavior of concrete beams without shear reinforcement. In spite of substantial experimental and theoretical efforts in the past, the mechanism of shear failure is not entirely understood. ALWAC is of importance to the current construction industry. Most of present concrete research focuses on high performance concrete, by which in meant a cost effective material that satisfies demanding performance requirements, including durability. The advantages of ALWAC are its reduced mass and improved thermal and acoustic insulation properties, while maintaining adequate strength. In spite of these advantages, its ultimate failure behavior has not been well defined for adequate design process. This paper will investigate mainly the shear behavior of reinforced ALWAC beam without web reinforcements numerically with experimental evidences.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.4A
• /
• pp.303-309
• /
• 2011

Laminated rubber bearing is the most commonly used device for seismic base isolation of bridge structures. It is important to know performance and behavior characteristics of the laminated rubber bearings. The main evaluation factors of the rubber bearing are classified as compressive, shear and tensile behavior characteristics. The reference data of compressive and shear characteristics are rich, but the reference data of tensile characteristics is scarce. In this study, tensile test results of the rubber bearing with variation of shape factor and shear deformation are investigated for mechanical property. When tensile deformation in normal condition is increasing, tensile cycle behavior curve becomes non-linear and tensile breaking point is 300%. On the other hand, tensile breaking point is shear deformation condition is about 40%. Furthermore, when shape factor is lower, tensile breaking point is decrease. This results mean that tensile breaking point is decreased in triaxial tensile deformation because of cracks caused by internal void of the rubber bearings. This experimental data can be used as the reference data of tensile characteristics for designing seismic isolation of structures.

• Journal of Korean Society of Steel Construction
• /
• v.26 no.1
• /
• pp.11-20
• /
• 2014

The Concrete Capacity Design(CCD) method has been used in the design of anchor since 2001 and Korean design code specify that concrete breakout capacity of CIP anchor under seismic load shall be taken as 75% of static capacity. In this study, an experimental study was performed to evaluate the concrete breakout capacity of unreinforced CIP anchors under dynamic shear force. For the purpose, three static and dynamic shear-loading tests were conducted using 20mm diameter anchors, respectively. The edge distance of 120mm was considered in the tests. In the dynamic tests, 15 cycles pulsating load with 1Hz speed was applied and the magnitude of loading step was increased until concrete breakout failure occurs. From the tests, the concrete breakout capacity under dynamic shear loading showed nearly same capacity by static loading.

• Journal of the Korean Geosynthetics Society
• /
• v.9 no.2
• /
• pp.33-40
• /
• 2010

In this study, the pullout tests are conducted to evaluate pullout resistance of steel strip reinforcement with transverse members. The test results are compared with theoretical equations and then the failure mechanism of transverse members is evaluated. The bearing resistance stress(${\sigma}^{\prime}_b$) of transverse members, which is applied pullout force at 50mm displacement, is closed from punching shear failure to general shear failure. The behavior by increment of a number of transverse members became closer to general shear failure. The behavior of transverse members at maximum pullout force, which is closed to general shear failure, is indicated that it is unrelated to normal stress and a number of transverse members. However, if the allowable displacement of reinforced soil wall is considered, it is impossible to apply in design. The test results are compared with bearing resistance evaluations using Prandtl's plastic theory and cylindrical cavity expansion theory. The analysis results are indicated that the bearing resistance by pullout tests is closed to predicted result by Prandtl's plastic theory, which are located between general shear failure and punching shear failure.

• Tunnel and Underground Space
• /
• v.16 no.5 s.64
• /
• pp.368-376
• /
• 2006

After heavy rainfall, It was occurred massive plane failure along bedding plane of shale in the center of rock slope. It was observed filling material and trace of underground water leakage around of the slope. We tried to find the cause for slope failure, and the result of examination showed that primary factors of the failure were low shear strength of clay filling material and water pressure formed within tension crack existed in the top of the slope. In this research, in order to examine the features of shear strength of filled rock joint, shear test of filled rock joint was conducted using of artificial filling material such as sand and clay..Also we made an investigation into the characteristics of shear strength with different thickness of filling materials.

• Journal of the KSME
• /
• v.32 no.6
• /
• pp.536-553
• /
• 1992

하중 종류 중에서 가장 기본적인 하중 중의 하나인 순수 전단력과 순수 굽힘 모멘트를 발생시 키고자 할 때는 아래와 같은 장치를 사용하는 것이 좋다. 1) 등방성체나 이방성체의 횡 전단계수 (G$_{12}$)와 횡 응력 프린지치(f$_{12}$) 등을 측정 하고자 할 때, 또는 모드 II (mode II)상태의 파괴역학을 연구하고자 할 때는 그림 1, 그림 2, 그림 3 그리고 그림 4 등에 제시된 것 중에서 적당한 것을 사용할 수 있다. 그러나 순수 전단 력이 발생되는 면적이 크고, 순수 전단력을 정확하고 균일하게 발생시키고자 할 때, 각 재료의 전단 물성치(shear properties) 측정, 모드II(mode II) 상태의 파괴역학을 연구하고자 할 때는 본 연구자가 고안한 H.I.S.T. 장치를 이용하면 편리하다. 2) 직선 보에 순수 굽힘 모멘트를 균일하고 정확하게 가하고자 할 대는 N.B.M.장치를 사용하는 것이 좋다. 또 N.B.M. 장치는 어느 보의 장치보다도 곡선보나 변형이 큰 보에도 더 정확하고 균일하게 순수 굽힘 모멘트를 발생시킬 수 있다.