• Korean Journal of Construction Engineering and Management
• /
• v.5 no.6 s.22
• /
• pp.212-217
• /
• 2004

Carbon fiber reinforced plastic(CFRP) plate Is one of the alterative materials for soengthening of reinforced and prestressed connote members due to excellent strength and light weight In this paper, the behavior of beams strengthened with CFRP plate and CFS(Carbon fiber sheet) is observed and analyzed from the test results. Especially specimens with thick plate is tested when large moment and large shear lone appear in same position. The main failure mode is a peeling-off of the CFRP plate near the loading points due to flexural-shear crack, Because of this failure mode, failure load is not linearly proportional to the thickness of CFRP plates. When beam is wrapped with CFS around oかy loading point it does not influence on the failure loads. Depending on the loading pattern, it is necessary to consider different design criteria for reinforced concrete members with external reinforcement. When line moment and large shear force appear in same location, maximum thickness may limit to 0.6mm and ratio between moment of strengthened beam and moment of unstrengthened beam is proposed 1.5-2.0. In order to use the plate of thicker than 6mm, CFS may be extended to the location which moment of strengthened beam is 1.5 times than moment of unstrengthened beam.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.847-850
• /
• 2008

In simply supported concrete beams with concentrated load, there is arch action that the internal lever arm length varies through shear span. Recently shear analysis model considering this effect has been developed, but the analysis algorithm is so complicated. Moreover, the variation of internal lever arm length is not considered on the shear compatibility condition. In this study, the shear analysis model is developed more simply and the variation of internal lever arm length is considered on the shear compatibility condition. From these modifications, an actual shear behavior of RC beams subjected to concentrated load could be expected from the results of the proposed analysis model.

• Journal of the Korea Concrete Institute
• /
• v.15 no.5
• /
• pp.689-696
• /
• 2003

Recently, Appendix A of ACI 318∼02 Code introduced the Strut-and-Tie Model(STM) procedure in shear design of deep flexural members. The STM procedure is widely used in the design of concrete regions where the distribution of longitudinal strains is significantly nonlinear, such as deep beams, beams with large openings, corbels, and dapped-end beams. Experimental study included five high-strength reinforced concrete deep beams with different detailing schemes for the horizontal and vertical reinforcement. The specimens were designed as simply supported beams subjected to concentrated loads on the top face and supported on the bottom face. At failure, all specimen exhibited primary diagonal crack running from the support region to the point load. Specimens which had mechanical anchorages(terminators) gives better representation of the load-carrying mechanism than the specimen had standard 90-degree anchorage at failure in deep flexural members. Based on the test results, shear design procedures contained in the ACI 318-99 Code, Appendix A of the ACI 318-02 Code, CSA A23.3-94 Code and CIRIA Guide-2 were evaluated. The Shear design of ACI 318-99 Code, Appendix A of the ACI 318-02 Code and CIRIA Guide-2 shown to be conservative predictions from 10% to 36% in the shear strength of the single-span deep beam which was tested. ACI 318-99 Code was the lowest standard deviation.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.14 no.3
• /
• pp.349-359
• /
• 2001

An enhanced four-node plate element, which has been developed for explicit dynamic analysis of plate, is described in this paper. Reissner-Mind1in(RM) assumptions are adopted to consider transverse shear deformation effects in the present plate element. RM plate element produces a shear locking phenomena in thin plate so that the substitute natural strains based on assumed strain method are explicitly derived. The present plate element is applied into the explicit transient algorithm and the mass matrix of plate is formulated by using special lumping method proposed by Hinton et al. The performance of the element is verified with numerical examples.

• The Journal of Engineering Geology
• /
• v.9 no.2
• /
• pp.135-145
• /
• 1999

Dynamic Shear modulus (G) is one of the imfortant dynamic soil properties to estimate the response of soil to dynamic loading. Problems in engineering geo1ogy practice the require the knowledge of soil properties subjected to dynamic loadings include soil-structure interaction during earthquakes, bomb blasts, construction operations, and mining. Although the dynamic shear modulus (G) is a time-dependent property, G change with time is often neglected. In this study, the effect of duration of confinement and its affecting factors (previous stress and strain, particle size and sustained pressure, and plasticity index) on the low-amplitude shear modulus ($G_{max}$) of soils are reviewed, and some empirical correlations based on mean particle diameter and plasticity index are proposed.

• Journal of the Korea Concrete Institute
• /
• v.23 no.2
• /
• pp.159-168
• /
• 2011

In the present study, an improved design method was developed for the punching shear strength of interior slabcolumn connections and column footings with and without shear reinforcement. In the evaluation of the punching shear strength, the possible failure mechanisms of the connections and column footings were considered. The considered failures modes were inclined tensile cracking of concrete, yielding of shear re-bars, and concrete crushing of compression zone/strut. The punching shear applied to the concrete critical section was assumed to be resisted mainly by the compression zone. The punching shear strength of the concrete compression zone was evaluated based on the material failure criteria of the concrete subjected to the compressive normal stress and shear stress. For verification of the proposed design method, its prediction was compared with the existing test results. The result showed that the proposed method predicted the strengths of the test specimens better than the current design methods of the KCI code for both the shear reinforced and unreinforced cases.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.393-400
• /
• 2003

지오멤브레인(geomembrane)과 다른 토목섬유, 즉 지오텍스타일 또는 GCL, 사이의 interface 전단거동을 특성화하는 strain-softening 모델을 개발하였다. 본 연구에 제안된 모델은 일차적으로 smooth 지오멤브레인과 textured 지오멤브레인을 대상으로 실시한 직접전단 시험결과를 대상으로 구축되었다. 시험을 통해 측정된 변위-전단응력의 관계는 strain-softening 현상를 고려하기 위해서 최대점이 발생하는 위치를 기준으로, pre-peak과 post-peak 영역으로 나누어 분석을 실시하였다. 실험결과를 토대로 구축된 모델식은 원 자료와의 비교를 통해 본 모델의 유효성을 검증하였다. 비교 결과 높은 연직 응력에서 약간의 차이를 보이긴 하지만, 대체적으로 실험 결과와 구축된 모델을 이용한 역계산의 값이 좋은 일치를 보임을 확인할 수 있었다. 특별히 연직응력이 낮은 단계에서는 높은 일치를 보였는데, 이를 통해 제안된 식이 매립지의 최종 cover와 같이 상재 연직하중이 작은 경우에 지오멤브레인이 포함된 interface의 전단 거동에 대한 합리적인 구성 방정식이 될 수 있음을 확인할 수 있었다.

• The Korean Journal of Rheology
• /
• v.9 no.3
• /
• pp.124-131
• /
• 1997

스테인레스 강(SUS 316L) 분말과 왁스계 결합제를 혼합하여 제조한 분말사출재의 유변학적 특성을 낮은 전단율에서 측정하기 위해 동심원반식 점성측정기를 이용하여 실험을 실시하였다. 측정기 벽면에서 발생하는 벽면 슬립(Slip)을 확인하고 벽면 슬립을 보정하기 위하여 두가지의 원반 간격에서 측정된 실험 자료를 이용하여 벽면 슬립을 보정하는 방법을 채택하였다. 실험 중, 측정 전단율범위를 제한하는 Thixotropy 현상을 발견학고 이에대한 원인분석을 위한 실험을 진행한 결과 과도한 전단응력에 의해서 분말사출재로부터 분리되어 나온 슬립층이 내부로 빠르게 흡수되어 들어가지 못하고 잔류하면서 Thixotropy 현상을 발 생시키는 것으로 판단되었다. Thixotropy 현상이 발생하지 않는 범위를 조사한후, 제한된 범위내에서 분말사출재의 유변학적 특성을 측정하였다. 측정된 자료는 항복응력을 지니는 유체의 특성을 표현하는 Bingham 식의 변형식에 잘 근사 되었으며, 슬립속도를 실험결과로 부터 계산한 결과 전단응력에 따라 선형적인 관계를 가지고 있는 점과 항복응력의 존재를 정성적으로 보여주는 결과를 얻었다.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.3
• /
• pp.540-548
• /
• 2016

The non-Newtonian flow curves of sodium bis-(2-ethylhexyl)sulfosuccinate-water lamellar liquid crystals were obtained in various concentrations and temperatures by using a cone-plate rheometer. By applying non-Newtonian flow equation to the flow curves for AOT-water lamellar liquid crystal samples, the rheological parameters were obtained. Particular attention is given to the hysteresis loop detected when the liquid crystal samples are shear under increasing-decreasing shear stress modes which result in thixotropic and dilatant behavior. Sodium bis-(2-ethylhexyl)sulfosuccinate-water lamellar liquid crystals behave as weak gels when they are subjected to shear flow, but when the applied stress surpasses the yield stress, they exhibit non-linear viscoelasticity. Upon decreasing shear rate, the dispersion still preserves much of its structure and consequently its shear stress remains higher than the values measured in the increasing shear rate mode.

• International Journal of Highway Engineering
• /
• v.7 no.4 s.26
• /
• pp.203-210
• /
• 2005

The penetration and viscosity tests have been used for the evaluation of the aged asphalt binder performance change. The improved test method has been required because the conventional tests could not evaluate the viscoelastic characteristics and the real behaviour of the aged asphalt binder. The conventional test methods using a different short term aged asphalt binder were tested and the test results were expressed as the penetration index and the residual penetration. The oscillatory and rotational mode tests were performed to find out the rheological characteristics of the short term aged asphalt binder in this study. The test results showed that the change of testing frequency, the speed of the vehicle effects the complex modules and phase angles. The creep compliance and shear viscosity also showed the different test results when the short term aged asphalt binders were tested. The rheological behavior should consider when the pavement design is conducted.