• Journal of the Korean Geotechnical Society
• /
• v.29 no.11
• /
• pp.107-118
• /
• 2013

Geosynthetic reinforced soil (GRS) walls have been increasingly applied recently due to its numerous geotechnical engineering applications. However failure occurs in some cases of constructed GRS walls. These GRS wall failures are mostly due to the unpredictable characteristics of intensive rainfall. Hence, the need for new and innovative ideas for rehabilitation methods has been getting attention. This paper introduces a case study for the design and restoration method of collapsed GRS wall using Limit equilibrium and Numerical Analyses. Restoration method includes: (1) soil nailing without backfill excavation and (2) reconstruction with GRS wall after collapsed backfill excavation. Analyses results show minimal horizontal displacements and shear strain on the reinforced concrete facing for the restoration case with soil nailing. On the other hand, horizontal displacements are developed in the middle of the mortar block facing and shear strains are developed at the bottom facing with spiral curves for the reconstructed GRS wall after collapsed backfill excavation. Therefore, the collapsed GRS wall was restored with the soil nailing without backfill excavation and its construction procedures are discussed in this paper.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.22 no.6
• /
• pp.639-646
• /
• 2009

High-flow steel-fiber reinforced mortar may induce a certain fiber orientation distribution in the process of placing and thus have an influence on the tensile properties. In this paper, the variation of the fiber orientation distribution according to the flow of high-flow steel-fiber reinforced mortar was estimated in numerical simulation. The analytical results present that the major variation of fiber orientation distribution is made within 150mm of flow distance, thereafter the tendency of the fiber orientation distribution is not noticeable even though the peak of distribution density in the orientation parallel to the flow direction get bigger along the distance. Considering the close relation between the fiber orientation and the tensile behavior of composite, prediction of fiber orientation distribution make it possible to predict the variation in the tensile behavior of high-flow steel-fiber reinforced mortar according to the flow.

• Land and Housing Review
• /
• v.1 no.1
• /
• pp.67-73
• /
• 2010

Method of protruding steel bar embedded in PHC pile for connecting with foundation plate is an intermediate form of fixed and hinged connection and has often been used in architectural structures such as apartment complex. However, mechanical properties of this method have not been proved and its construction process is not simple. In this study, therefore, by analyzing previous research and by considering ratio of steel bar and concrete in PHC pile, which is minimum reinforcement of rebar, the newly optimized method of reinforcing joint of PHC pile and foundation plate is suggested with respect to PHC pile type (PHC 450, PHC 500, and PHC 600). To assess mechanical properties (ultimate tensile and shear strength) of joint of PHC pile and foundation plate, full scale experimental tests are performed. As a result, all cases are satisfied with required design criteria and can be practically applied. Our results indicate that reduction of rebar reinforcement compared to previous method would lead cost saving in PHC pile construction.

• Journal of the Korean Geosynthetics Society
• /
• v.3 no.4
• /
• pp.3-12
• /
• 2004

In this paper, a mechanism of the soil structure reinforced by geosynthetics is discussed. The reinforcing mechanism is interpreted an effect arising from the reinforcement works so as to prevent the dilative deformation (negative dilatancy) of soil under shearing. A full-scale in-situ model test was carried out in Kanazawa of Japan(1994) and in the laboratory test the strength and the characteristics of deformation conducting a constant volume shear test are examined. The parameters needed in the FEM are also applied by using the experimental data. The elasto-plastic finite element simulation is carried out, and the results are quantitatively compared with that of experiment. As a results, it is known that the theoretical predictions could be explained effectively the experimental results which are obtained by a full-scale in-situ model test.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.5
• /
• pp.999-1011
• /
• 1989

A consideration on the trubulence models for describing the redeveloping turbulent boundary layer beyond separation-reattachment in the flow over a backward-facing step is given through experimental and numerical studies. By considering the blance among the measured values of respective terms in the transport equations for the turbulent kinetic energy and the turbulent shear stress, the recovering process of the redeveloping boundary layer from non-equilibrium to equilibrium has been investigated, which takes place slowly over a substantial distance in the downstream direction. In the numerical study, the standard K-.epsilon. model and the Reynolds stress model have been applied to two kinds of flow regions, one for the entire downstream region after the backward-facing step and another for the downstream region after reattachment. Then the results are compared to a meaningful extent, with the experimental values of the turbulent kinetic energy k, the turbulent energy production term P, the dissipation term K-.epsilon. model, a necessity for a new modelling has been brought forward, which can be also applied to the case of the nonequlibrium turbulent flow.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.10
• /
• pp.29-38
• /
• 2011

The unsaturated layers by rainfall infiltration are not properly reflected in construction codes to do slope design. The objective of this paper is to analyze the slope behavior according to the saturation layer increase resulted from the rainfall infiltration, to do that the laboratory slope model apparatus was adopted. From the model apparatus, the variation of water content and strength parameters of the model slope were analyzed. The safety factors of model slope was decreased, if saturation layer was increased from 3.0m to 4.5m, which means ground water level 3m selected from construction codes makes higher safety level. Also, if the ground water level is located in soil surface, the lower safety level will show up. Therefore, to make the proper slope design, the experiments and analysis of variation of saturation layer is needed.

• Composites Research
• /
• v.34 no.2
• /
• pp.101-107
• /
• 2021

Composite structures have components and joints. Theses connections or joints can be potentially weak points in the structure. The failure mode of the composite bolted joint is designed as a bearing failure mode for structural safety. The load-displacement relation exhibits bearing failure mode shows a nonlinear behavior after the initial failure and progressive failure behavior. In order to accurately predict the failure behavior of composite bolted joints, this study modified the shear damage variable calculation process in the existing progressive failure analysis model. The results of the bearing stress-bearing strain of the composite bolted joint were predicted using the modified progressive failure analysis model, and the modified model was verified through comparison with the previous progressive analysis model.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.24-24
• /
• 2021

자연하천 바닥 경계층 내에서는 복잡한 난류 구조가 형성되며 이들은 하상에 강한 모멘텀을 전달한다. 바닥 부근에 분포하는 유사 입자들은 경계층 내에서 발생한 난류 흐름으로부터 모멘텀을 전달받아 소류사 혹은 부유사 형태로 이송되게 되며, 이러한 유사 이송 과정을 역학적으로 설명하기 위해서는 경계층 내 유체 흐름에 대한 이해가 선행되어야한다. 경계층 내 난류 흐름 특성이 유사 입자의 움직임에 미치는 영향에 대해 분석하기 위해서는 바닥 경계층 내 고해상도 유속 자료와 유사 움직임을 동시에 포착할 수 있는 기술이 요구된다. 하지만 현재까지 수행된 대부분의 선행 연구들은 점 유속을 측정할 수 있는 음파 도플러 유속계 (Acoustic Doppler Velocimetry) 혹은 2차원 입자 영상 유속계를 활용하였으며, 이들은 복잡한 3차원 난류 흐름 특성을 분석하기에는 한계가 있다. 본 연구의 목적은 실험실 실험을 통해 바닥 경계층 내 3차원 난류 흐름이 유사 이송에 미치는 영향에 대해 조사하는 것이다. 본 연구에서는 유사 주변에서의 고해상도 3차원 흐름 유동장 및 순간적인 유사 움직임에 대해서는 합성 개구 (synthetic aperture) 기반의 3차원 입자 영상 유속계 및 입자 추적 유속계를 활용하여 취득하였다. 취득된 흐름 유동장을 기반으로 레이놀즈 전단응력을 산정하였으며 이를 통해 유체가 하상에 미치는 모멘텀의 크기를 파악하였다. 복잡한 난류 흐름 구조에 대해서는 팔분원 분석 (octant analysis)을 통해 구분했으며, 유사가 움직이는 순간의 유속장을 기반으로 유사 이송을 발생시키는 지배적인 난류 흐름 특성에 대해 규명하였다. 본 연구는 바닥 경계층 내 복잡한 3차원 난류 흐름과 유사 입자의 움직임을 동시에 분석함으로써 기존에 수행되어왔던 선행 연구들의 한계점을 극복하고 보다 명확한 유사 이송의 발생 원인에 대해 분석했다는 점에 의의가 있다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.1C
• /
• pp.33-39
• /
• 2009

Vertical soil stress near a pile subjected to negative skin friction (NSF) may be reduced due to shear transfer at the pile-soil interface. A three-dimensional finite difference analysis has been performed to clarify the influence of vertical and horizontal stress reductions on the pile behavour. In addition, a simple equation has been proposed to estimate vertical stress reduction of the soil near the pile. The vertical and horizontal stresses are reduced by substantial amount compared to corresponding stress components at the Greenfield condition. The horizontal extent of vertical stress reduction of the soil near the pile is rather limited to about up to 4-8 D, where D is the pile diameter. The findings from the current research indicate that widely used $\beta$-method may result in over-estimation of dragload (compressive force on piles due to NSF) and hence stress reduction needs to be incorporated in the original equation.

• The Bulletin of The Korean Astronomical Society
• /
• v.38 no.2
• /
• pp.83.1-83.1
• /
• 2013

선형비점수차를 완벽하게 제거한 비축반사경 이론을 천체 관측용 분광기의 전단 광학계 등에 응용하면 색수차가 없는 기기 제작이 가능하다. 이러한 비축 반사경은 DTM(Diamond Turning Machine)을 이용하여 알루미늄으로 만들면 제작 시간이 단축된다. 그러나 DTM을 이용해 알루미늄과 같이 무른 금속을 가공할 경우 툴마크가 발생하게 된다. 툴마크는 회절현상을 발생시키며 이러한 회절현상은 알루미늄 반사경을 이용한 광학계 개발에 제약이 된다. 툴마크는 DTM 가공 이후 연마를 통해 제거할 수 있지만 알루미늄의 무른 특성으로 인해 연마 과정에서 반사경의 형상이 변할 가능성이 크다. 이러한 알루미늄 반사경의 형상 변화를 최소화하기 위한 방법으로는 알루미늄 반사경 표면에 무전해니켈도금을 하는 것이다. 하지만 도금 과정에서 반사경의 형상이 변할 가능성이 있기 때문에 두가지 방법을 사용하여 툴마크를 제거할 계획이다. 첫 번째 방법은 DTM 가공된 알루미늄 반사경을 5 um의 무전해니켈도금 이후 연마하여 툴마크를 제거하고 반사율 증가를 위해 그 위에 다시 알루미늄 코팅을 하는 방법니다. 두 번째 방법은 100 um의 무전해니켈도금 이후 DTM 가공을 하고 다시 연마를 통해 툴마크를 제거하는 방법이다. 이번 발표에서는 툴마크를 제거하기 위한 2가지 방법의 장단점을 확인하고 툴마크를 제거한 알루미늄 반사경을 제작하기 위한 과정을 설명하였다. 본 연구에서 개발한 비축 반사경은 서울대학교 창의연구단의 광학/적외선 카메라 CQUEAN의 차세대 모델에 적용할 계획이다.