• Fire Science and Engineering
• /
• v.26 no.1
• /
• pp.61-67
• /
• 2012

In the three-phase power system using the three-phase motor, when any one-phase is open-phase, the unbalanced current flows and the single-phase power supplied by power supply produces overcurrent to motor coil. As a result, the enormous damage and electrical fire can be given to the power system. Recently, the thermal over-current relay (THR) or electronic motor protection relay (EMPR) is mostly used as the open-phase detection device of the three-phase motor. When the over-current or overheat of electric line is generated, it detects and operates circuit breaker, but there is the defect that the sensing speed is slow, the operation can be sometimes failed, and the precision is decreased. In order to improve these problems, this paper is proposed a new control circuit topology for openphase protection using semiconductor devices. Therefore, the proposed open-phase protection device (OPPD) enhances the sensing speed and precision, and has the advantage of simple fitting in the three-phase motor control panel in the field, as it manufactures into small size and light weight. As a result, the proposed OPPD protects the three-phase motor, minimizes the electrical fire from openphase, and contributes for the stable driving of the power system. The performance and confidence of the proposed OPPD is confirmed by a great variety of the experiments of operation characteristic.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.5
• /
• pp.635-643
• /
• 2018

This paper propose a method to identify the motor parameters and improve input voltage error which affect the low speed position error of the back-emf(back electromotive force) based sensorless algorithm and to secure the operation reliability and stability even in the case where the load fluctuation is severe and the start and low speed operation frequently occurs. In the model-based observer used in this paper, stator resistance, inductance, and input voltage are particularly influential factors on low speed performance. Stator resistance can cause resistance value fluctuation which may occur in mass production process, and fluctuation of resistance value due to heat generated during operation. The inductance is influenced by the fluctuation due to the manufacturing dispersion and at a low speed where the change of the current is severe. In order to find stator resistance and inductance which have different initial values and fluctuate during operation and have a large influence on sensorless performance at low speed, they are commonly measured through 2-point calculation method by 2-step align current injection. The effect of voltage error is minimized by offsetting the voltage error. In addition, when the command voltage is used, it is difficult to estimate the back-emf due to the relatively large distortion voltage due to the dead time and the voltage drop of the power device. In this paper, we propose a simple circuit and method to detect the voltage by measuring the PWM(Pulse Width Modulation) pulse width and compensate the voltage drop of the power device with the table, thereby minimizing the position error due to the exact estimation of the back-emf at low speed. The suitability of the proposed algorithm is verified through experiment.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.4
• /
• pp.34-40
• /
• 2004

In this paper, we have studied the OCT(Optical Coherence Tomography) system which has been advantages of high resolution, 2-D cross-sectional images, low cost and small size configuration. The characteristics of light source determine the resolution and coherence length. The light source has a commercial SLD with a central wavelength of 1,285 ill11, 35.3 nm(FWHM). The optical delay line is necessary to make equal with the optical path length to scattered light or reflected light from a sample. In order to make equal the optical path length, the stage that is attached to a reference mirror is controled by a step motor. And the interferometer is configured with the Michelson interferometer by using a single mode fiber, and the scanner can be focused on the sample by using a reference ann Also, the 2-dimension cross-sectional images were measured with scanning the transverse direction of the sample by using a step motor. After detecting the internal signal of lateral direction, a scanner is moved to obtain the cross-sectional image of 2-dimension by using step motor. A photodiode, which has high detection sensitivity and excellent noise characteristics has been used. The detected small signal has a noise and interference. After filtering and amplifying the signal, the output signal is demodulated the waveform And then, a cross-sectional image is seen through converting this signal into a digitalized signal by using an AID converter. The resolution of the sample is about 30${\mu}{\textrm}{m}$, which corresponds to the theoretical resolution. Also, the cross-sectional images of onion cells were measured in real time scheme.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.5
• /
• pp.286-291
• /
• 2014

In this study, novel ultrasonic rotary motor of hexadecagon shape stator was proposed. Stator of the hexadecagon ultrasonic motor was composed of an elastic ring and ceramics. The elastic ring had sixteen sides and sixteen angular points. Eight ceramics were attached on the outer surface of the eight sides of the ring. When rotor of cylindrical shaft was inserted inside of the ring stator, central lines of the sixteen sides of the stator hold the shaft by the slight pressures(frictions). This slight pressure was a preload of the motor and it could be controlled by radius and thickness of the ring. When two sinusoidal voltages which have 90 degree phase difference were applied to each four ceramics, elliptical displacements of inner surface of the ring were obtained. These elliptical displacements of the inner surface rotated the shaft rotor through the frictions. The proposed hexadecagon ultrasonic motor was designed and analyzed by using the finite element method (FEM), depending on materials of the elastic ring. Based on the FEM results, one model of motor which showed maximum displacement at contact points was chosen and fabricated. And characteristics of the motor were compared with simulated results. When the motor was fabricated with these results, EL20ET0.5CT0.5CW2 model showed 115[rpm] speed about input voltage of 60[Vrms] at 65.6[kHz]. And the maximum torque of 6[gfcm] was obtained. From these results, the hexadecagon shaped ultrasonic motor can be used to actuator for optical device which needs detailed position control. Also it can be used to medical and portable device by reducing size and weight.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.6
• /
• pp.397-402
• /
• 2016

To produce adequate electricity in nuclear and thermal power plants, an optimal amount of steam should be supplied to a generator connected to high- and low-pressure steam turbines. A turbine output control device, which is a special steam valve employed to supply or interrupt the steam to the turbine, is operated using a hydraulic servo actuator. In power plants, the performance of servo actuators is degraded by the air generated from the hydraulic system, or causes frequent failures owing to an increase in the wear of the seal. This is due to the seal being burnt as generated heat using the produced compressed air. Some power plants have exhausted air using a fixed orifice, and thus they encounter power loss due to mass flow exhaust. Failures are generated in hydraulic pumps, electric motors, and valves, which are frequently operated. In this study, we perform modeling and analysis of the load-sensing air-exhaust valves, which can be passed through very fine flow under normal use conditions, and exhaust mass flow air at the beginning stage as with existing fixed orifices. Then, we propose a method to prevent failures due to the compressed air, and to ensure the control accuracy of hydraulic servo actuators.

• Journal of Welding and Joining
• /
• v.15 no.6
• /
• pp.24-31
• /
• 1997

2매의 금속을 맞대어 그 한 쪽에 접촉면과 평행하게 고주파진동을 가하면 단 시간에 접합된다. 이공정을 초음파 용접이라고 하며 그 물리적인 본질은 아직 불분명 하지만, 첫째로는 강한 마찰에 의해 금속 자유면의 산화물층이 제거되기 때문이라는 점과 둘째로는 마찰에 의해 금속 표면이 강하게 가열되어 이에 따른 연화에 의해 접합 이 된다고 하는 점이다. 그러나 이와 같이 가열된다고 하더라도 가열은 표면부에만 국한되고 다른 부분은 가열되지 않는다. 따라서 초음파용접은 냉간접합이라고도 한다. 또 가압력과 진동에 의한 힘이 동시에 작용하기 때문에 용접할 면을 미리 청정하게 할 필요는 없고 용접전의 단계에서 자연적으로 청정화가 이루어진다고 하는 사실이 간접 적으로 증명되고 있다. 초음파 용접(Ultrasonic welding)의 특징을 요약하면 고상용접 의 일종으로서 용접중에 국부적으로 고주파 진동에너지와 압력을 가하여 용접하는 방법이다. 이 때 모재를 용융시키지 않고 건전한 야금학적 결합부가 얻어진다는 데에 큰 특징이 있다. 또한 초음파용접은 다른 용접법에 비해 경제성이 매우 높고, 초음파 용접에 필요한 출력이 전기아크 용접에 필요한 출력의 5 - 10%로 충분한 경우가 많다. 초음파 용접은 통상의 방법으로는 용접하기 어려운 동종 금속이나 이종 금속의 용접에 널리 사용된다. 이 용접법은 반도체, 미세회로, 전기 접점의 형성에 대한 생산기술 로서 사용되고 있는데 소형 모터, 알루미늄 박의 가공, 알루미늄 합금의 조립 등에 이용되고 있다. 한편 최근에는 자동차, 우주항공산업 분야의 구조제 용접용으로도 채용되고 있다.출함이 바람직하다.분비되는 배설-분비 항원의 자극과 깊은 관계가 있음을 알 수 있었다.넌트 명세서를 대한 XML DTD(Document Type Definition)를 정의하고, HTML 기반 검색 방법과 XML 기반 검색 방법에 대한 컴포넌트 검색 성능을 비교한다.따라 NO 생산 및 세포독성이 증가하였고. NO 생산을 저하시키는 약제들은 활성화된 복강 대식세포 및 RAW264.7 세포에 의한 질편모충에 대한 세포독성을 현저히 감소시키는 것으로 보아 NO는 질편모충에 대한 대식세포의 숙주 방어기전에서 중요한 역할을 감당할 것으로 생각된다.nction index) 와 최대개구시 동통의 정도는 시술전과 시술 4주후간에 유의한 차이가 관찰되었다.피부온도는 검사자간에는 특정부위에 따라 다소 차이가 있을 수 있으나 일반적으로 높은 재현성을 보여줌으로서 향후 교근 및 측두근의 임상연구 평가에 피부온도조사는 도움이 되리라 사료된다. lactobacilli의 양은 peroxidase system을 함유하거나(p < 0.01) 함유하지 않은(p < 0.05) 치약을 사용한 군 모두에서 양치전에 비해 유의성있게 감소하였다. 6. 양치후 30분에 채취한 구강건조증 환자의 자극성 전타액내 S. mutans 양은 peroxida system을 함유한 세치제를 사용한 군에서 대조군에 비해 유의성있게 낮았다(p < 0.05). 7. 양치후 30분에 채취한 구강건조증 환자의 자극성 전타액내 lactobacilli양은 peroxidase system을 함유한 세치제를 사용한 군에서 대조군에 비해 상대적으로 낮게 나타났으나(p = 0.067)

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.1
• /
• pp.31-36
• /
• 2012

Military vehicles, compared to conventional vehicles, require higher driving performance, quieter operation, and longer driving distances with minimal fuel supplies. The series hybrid electric vehicle can be driven with no noise and has high initial startup performance, because it uses only a traction motor that has a high startup torque to drive the vehicle. Moreover, the fuel economy can be improved if the vehicle is hybridized. In series hybrid electric vehicles, the electric generation system, which consists of an engine and a generator, supplies electric energy to a battery or traction motor depending on the vehicle driving state and battery state of charge (SOC). The control strategy determines the operation of the generation system. Thus, the fuel economy of the series hybrid electric vehicle relies on the control strategy. In this study, thermostat, power-follower, and combined strategies were compared, and a 37% improvement in the fuel economy was implemented using the combined control strategy suggested in this study.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.139-141
• /
• 2005

이번 실험에서는 변방전형 교류 PDP에서의 3차원적인 전자온도와 이온밀도의 측정을 마이크로 랑뮈르 탐침법을 통해 실험적으로 연구하였다. 스테핑 모터에 연결된 마이크로 랑뮈르 탐침은 20um씩 움직이며 탐침에 인가하는 플러스와 마이너스의 직류전압을 통해 I-V곡선을 구할 수 있고 이를 통해서 전자온도와 플라스마 밀도를 구할 수 있다. Ne+Xe(4%) 200Torr의 혼합가스에서 전극의 테두리를 따라(X축) 전자온도 및 플라스마 밀도를 측정한 결과 중앙지점에서와 전극의 경계지역에서 이온밀도는 $7.69{\sim}11.1{\times}10^{11}cm^{-3}$ 까지 측정되었다. 또한 전자온도는 플라스마 밀도와 균형적인 관계에 있다는 것은 주목할 만하다. 전자온도는 전극 사이의 중심에서 가장 적게 1.3 ~ 3.15eV까지 측정되었다. Y축으로 측정했을 경우 이온 밀도와 전자온도는 전극 갭 중앙에서부터 약 80um 떨어진 지점에서 서로 교차하며 증가 및 감소였으며 이온밀도는 $8.3{\sim}11.1{\times}10^{11}cm^{-3}$로 측정되었고 전자온도는 이와 균형적인 관계를 가지고 1.2~1.6eV로 측정되었다. 또한 이러한 특성은 AC PDP 에서 나타나는 줄무늬 현상과 관련이 있는 것으로 보인다. Z축으로 측정했을 경우 약 125um높이에서 가장 높게 측정되었으며 $1.1{\times}10^{12}cm^{-3}$정도로 측정되었다.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.4
• /
• pp.456-465
• /
• 2019

PHEV(Plug in Hybrid Electric Vehicle) and BEV(Battery Electric Vehicle) equip high voltage batteries to drive motor and vehicle electric system. Those vehicle require OBC(On-Board Charger) for charging batteries and LDC(Low DC/DC Converter) for converting from high voltage to low voltage. Since the charger and the converter actually separate each other in electrical vehicles, there is a margin to reduce the vehicle weight and area of installation by integration two systems. This paper studies a 1.5kW LDC converter that can be integrated into an OBC using an isolated current-fed converter by simplifying the design of LDC transformers. The proposed LDC can control the final output voltage of the LDC by using a fixed arbitrary output voltage of the bidirectional buck-boost converter, so that Compared to the existing OBC-LDC integrated system, it has the advantage of simplifying the transformer design considering the battery voltage range, converter duty ratio and OBC output turn ratio. Prototype of the proposed LDC was made to confirm normal operation at 200V ~ 400V input voltage and maximum efficiency of 91.885% was achieved at rated load condition. In addition, the OBC-LDC integrated system achieved a volume of about 6.51L and reduced the space by 15.6% compared to the existing independent system.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.148-155
• /
• 2021

As robot technology advances, research on the driving system of mobile robots is actively being conducted. The driving system of a mobile robot configured based on two-wheels and four-wheels has an advantage in unidirectional driving such as a straight line, but has disadvantages in turning direction and rotating in place. A ball robot using a ball as a wheel has an advantage in omnidirectional movement, but due to its structurally unstable characteristics, balancing control to maintain attitude and driving control for movement are required. By estimating the position from an encoder attached to the motor, conventional ball robots have a limitation, which causes the accumulation of errors during driving control. In this study, a driving control system was proposed that estimates the position coordinates of a ball robot through image processing and uses it for driving control. A driving control system including an image processing unit, a communication unit, a display unit, and a control unit for estimating the position of the ball robot was designed and manufactured. Through the driving control experiment applying the driving control system of the ball robot, it was confirmed that the ball robot was controlled within the error range of ±50.3mm in the x-axis direction and ±53.9mm in the y-axis direction without accumulating errors.