• Korean Journal of Materials Research
• /
• v.10 no.9
• /
• pp.593-600
• /
• 2000

This paper investigated the conduction path and conduction mechanism in undoped polycrystalline diamond thin films deposited by microwave chemical vapor deposition. The resistances measured by ac impedance spectroscopy with different directions can not be explained by the previously-known surface conduction model. The electrodeposition of Cu and electroetching of Ag experiments showed that the conduction path is the grain boundaries within the diamond films. The electodeposition of Cu with an insulating surface layer further proved that the main conduction path in polycrystalline films in the grain boundaries. The film with high electrical conductivity has low activation energy of 45meV and higher dangling bond density. By considering the results and surface C chemical bonds, the H-C-C-H bonds at surface and in grain boundaries might be the origin of high conductivity in undoped diamond films.

• Applied Chemistry for Engineering
• /
• v.9 no.6
• /
• pp.870-877
• /
• 1998

With impedance spectrum measurements, impedance was studied in the interface between sample solutions for $K^+-ion$ selective PVC membrane electrode containing neutral carriers [dibenzo-18-crown-6 (D18Cr6) and valinomycine (Val)]. Response characteristics of electrode were examined by measuring AC impedance spectra that were resulted from the chemical structure and the content of carrier, variation of plasticizer, membrane thickness, doping of base electrolytes, and concentration variation of sample solution. Transport characteristics of PVC membrane electrode were also studied. It was found that the equivalent circuit for the membrane in $K^+$ solution could be expressed by a series combination of solution resistance and a parallel circuit consisting of the bulk resistance and geometric capacitance of the membrane system. But the charge transfer resistance and Warburg resistance were overlapped a little in the low concentration and low frequency ranges. The carrier, D18Cr6 was best for electrode and impedance characteristics, and ideal electrode characteristics were appeared especially in case of doping of the base electrolyte[potassium tetraphenylborate(TPB)]. The optimum carrier content was about 3.23 wt% in case of D18Cr6 and Val. DBP was best as a plasticizer. As membrane thickness decreased the impedance characteristics was improved, but electrode characteristics were lowered for membrane thickness below the optimum. In the case of D18Cr6, the selectivity coefficients by the mixed solution method for the $K^+$ ion were the order of $NH_4{^+}>Ca^{2+}>Mg^{2+}>Na^+$.

• Journal of the Korean Electrochemical Society
• /
• v.23 no.3
• /
• pp.66-72
• /
• 2020

In this study, the development of biosensors capable of bi-enzyme reactions by including Horseradish peroxidase and glucose oxidase was carried out for detection of glucose. The sensors were manufactured using electro deposition method to reduce production time, and screen printed electrodes (SPE) were used to produce economical sensors. To check the bienzyme effect, the sensor was compared and analyzed with single enzyme biosensor. The characteristics of the sensor were evaluated using scanning electron microscopy(SEM), cyclic voltammetry(CV), electrochemical impedance spectroscopy(EIS), chronoamperometry(CA), and flow injection analysis(FIA). Analysis results from SEM, CV and EIS confirmed that the enzymes are well fixed to the electrode surface. In addition, it was confirmed that bi-enzyme biosensors manufactured from the CA method improved signal performance by 200% compared to single enzyme biosensors. From this results, we were able to explain that HRP and GOD react catalyzed to each other. And the results of FIA showed that the intensity of each current signal was constant when the same concentration of glucose was injected four times. In addition, by analyzing the intensity of current signals for glucose concentrations, the biosensors manufactured in this study showed excellent trends in signal sensitivity, reproducibility and stability.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.214-214
• /
• 2003

고체 고분자 전해질에 대한 연구는 1979년 wright와 Armand에 처음 시작된 이래로 지난 20여년간 연구가 계속적으로 지속되고 있다. 전지의 적용되기 위해 전해질이 갖추어야 할 조건중에 이온전도도가 상온에서 10-4 S/cm 이상의 전도도를 나타내야 하지만 지금까지 연구되고 있는 여러 고체 고분자 전해질은 이런 조건을 만족시키지 못하고 있는 실정이다. 본 연구에서는 이런 상온에서의 이온 전도성을 향상시키기 위해 여러 종류의 실리카와 세라믹 계열의 첨가제를 첨가하여 이온전도성의 향상을 꾀하고자 하였다. 본 연구에서는 고체 고분자 전해질의 host polymer로써 분자량 400,000 의 Polyethylene oxide를 사용하였으며 Lithuim salt로는 Lithium (bisperfluroethylsulfonyl)imide(3M)를 기본적으로 사용하였다. 여기에 가소제의 역활로써 (3-cyanopropyl)methylsiloxane cyclics를 첨가하였고 표면그룹이 CH3와 OH기로 이루어진 기능성 나노 실리카를(<11nm)이용하여 함량별 전기 화학적 특성 및 기본 물성을 측정하였다. 기본적으로 이 네 가지 물질을 유기용매 Acetonitril에 잘 용해하여 Solid Casting방법으로 80-100 마이크로의 복합고분자 전해질을 제조하였다. Homogeneous하고 uniform한 필름 제조하기 위해 9$0^{\circ}C$에서 열처리를 24h 동안 실시하였다. 제조되어진 복합고분자전해질은 XRD를 통하여 결정성을 조사하였고 DSC를 이용하여 유리 전이온도 및 결정화도를 조사하였다. 복합고체고분자의 전기화학적 성질을 평가하기 위해 blocking electrode를 제작하여 임피던스 스펙트로 스코피를 이용하여 이온전도성을 측정하였다. 또한 복합 고분자 전해질의 온도의존성에 대해서도 조사하였다. 또한 실제 전지의 작동구간에서의 전해질의 안정성을 확인하기 위해 LSV를 측정하였고. Li metal을 사용하여 non-blocking electrode를 제작하여 복합고분자 전해질과의 계면저항을 측정하였다.

• Journal of the Korean Electrochemical Society
• /
• v.22 no.2
• /
• pp.53-59
• /
• 2019

To examine the solution structure of electrolytes, it is very important to understand ion-ion and ion-solvent interactions. In this review, we introduce the basic principle of dielectric relaxation spectroscopy (DRS) and studies of electrolyte structure. DRS is a type of impedance method, which measures the dielectric properties of electrolytes over a high frequency domain at levels of tens of GHz. Therefore, DRS provides information on the different polar chemical species present in the electrolyte, including the type and concentration of free solvents and ion pairs with dipole moments. The information of DRS is complementary to the information of conventional analytical techniques (Infrared/Raman spectroscopy, nuclear magnetic resonance (NMR), etc.) and thus enables a broad understanding of electrolyte structure.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.6
• /
• pp.761-769
• /
• 1999

In this paper the effect of aging heat treatment to the Corrosion behavior for the Nimonic 80A superalloy was studied by AC Impedance methods. Tested solution was 3.5% with tempera-ture $25^{\circ}C$ Electro-chemical corrosion test were carried out for the Nimonic 80A super-alloy which solution heat treated at $1080^{\circ}C$ for 8 hours followed by aging heat treated at $650^{\circ}C,\;700^{\circ}C,\;750^{\circ}C\;800^{\circ}C$ and $850^{\circ}C$ with 16hours under vacuum environment. The obtained results were as follows; 1. Base metal and solution-treated materials were exhibited similar corrosion tendency as Ran-dle equivalent cell. The value of passive film resistance was 579 ohms for the base metal and 124,770 ohms for the solutionized metal such a difference was arose by the ${{\gamma}_^'}$ precipitate on the metal surface during heat treatment. 2. The measure value of $R_p$ for heat-treated at $650^{\circ}C,\;700^{\circ}C,\;800^{\circ}C$and $850^{\circ}C$ were 97,943, 93, 111, 26,961, 15,798 and 11,780ohm respectively. Which indicated that the passive film resistance Rp was reduced as aging temperature increased due to the growth of grain size and sensitization at the grain boundary. 3. The similar tendency was exhibited for corrosion behavior of the electro-chemical corrosion polarization method and AC impedance method and confirmed that AC impedance method was useful tool for corrosion research.

• Applied Chemistry for Engineering
• /
• v.17 no.2
• /
• pp.183-187
• /
• 2006

The choice of solvents for electrolytes solutions is very important to improve the characteristics of charge/discharge in the Li-ion battery system. Such solvent systems have been widely investigated as electrolytes for Li-ion batteries. In this paper, the electrochemical properties of the solid electrolyte interphase film formed on carbon anode surface and the solvent decomposition voltage in 1 M LiPF6/EC:MA(x:y) electrolyte solutions prepared from the various mixing volume ratios are investigated by chronopotentiometry, cyclic voltammetry, and impedance spectroscopy. As a result, the solvent decomposition voltages are varied with the ionic conductivity of the electrolyte. Electrochemical properties of the passivation film were different, which are dependent on the mixture ratio of the solvents. Therefore, the most appropriate mixing ratio of EC and MA as a solvent in 1 M $LiPF_6/(EC+MA)$ system for Li-ion battery is approximately 1:3 (EC:MA, volume ratio).

• Korean Chemical Engineering Research
• /
• v.55 no.5
• /
• pp.593-599
• /
• 2017

In order to enhance ultra battery performances, the electrochemical characteristics of nano Pb/AC anode composite was investigated. Through nano Pb adsorption onto activated carbon, nano Pb/AC was synthesized and it was washed under vacuum process. The prepared anode materials was analysed by SEM, BET and EDS. The specific surface area and average pore size of nano Pb/AC composite were $1740m^2/g$ and 1.95 nm, respectively. The negative electrode of ultra battery was prepared by nano Pb/AC dip coating on lead plate. The electrochemical performances of ultra battery were studied using $PbO_2$ (the positive electrode) and prepared nano Pb/AC composite (the negative electrode) pair. Also the electrochemical behaviors of ultra battery were investigated by charge/discharge, cyclic voltammetry, impedance and rate capability tests in 5 M $H_2SO_4$ electrolyte. The initial capacity and cycling performance of the present nano Pb/AC ultra battery were improved with respect to the lead battery and the AC-coated lead battery. These experimental results indicate that the proper addition of nano Pb/AC into the negative electrode can improve the discharge capacity and the long term cycle stability and remarkably suppress the hydrogen evolution reaction on the negative electrode.

• Applied Chemistry for Engineering
• /
• v.28 no.5
• /
• pp.534-538
• /
• 2017

In this study, the molecular weight controlled pitches derived from pyrolyzed fuel oil (PFO) were prepared using solvent extraction and were carbonized. Electrochemical characteristics of lithium battery anode materials were investigated using these petroleum pitches. Three pitch samples prepared by the thermal reaction were 3903 (at $390^{\circ}C$ for 3 h), 4001 (at $400^{\circ}C$ for 1 h) and 4002 (at $400^{\circ}C$ for 2 h). The prepared hexane insoluble pitches were analysed by XRD, TGA, SEM and Gel permeation Chromatography (GPC). The electrochemical characteristics of the PFO-derived pitch as an anode material were investigated by constant current charge/discharge, cyclic voltammetry and electrochemical impedance tests. The coin cell using pitch (4001) and the electrolyte of $LiPF_6$ in organic solvents (EC : DMC = 1 : 1 vol%, VC 3 wt%) has better initial capacity (310 mAh/g) than that of other pitch coin cells. Also, this carbon anode showd a high initial efficiency of 82%, retention rate capability at 2 C/0.1 C of 90% and cycle retention of 85%. It was found that modified pitches improved the cycling and rate capacity performance.

• Korean Chemical Engineering Research
• /
• v.58 no.1
• /
• pp.142-149
• /
• 2020

In this study, the electrochemical performance of Graphite/Silicon/Pitch composites as anode material was investigated to improve the low theoretical capacity of artificial graphite. Spherical artificial graphite surface was coated with polyvinylpyrrolidone (PVP) amphiphiles material to synthesize Graphite/Silica material by silica islands growth. The Graphite/Silicon/Pitch composites were prepared by petroleum pitch coating and magnesiothermic reduction. The Graphite/Silicon/Pitch composite electrodes manufactured using poly(vinylidene fluoride) (PVDF), carboxymethyl cellulose (CMC) and polyacrylic acid (PAA) binders. The coin type half cell was assembled using various electrolytes and additives. The Graphite/Silicon/Pitch composites were analysed by X-ray diffraction (XRD), scanning electron microscope (SEM) and a thermogravimetric analyzer (TGA). The electrochemical characteristics of Graphite/Silicon/Pitch composite were investigated by constant current charge/discharge, rate performance, cyclic voltammetry and electrochemical impedance spectroscopy. The Graphite/Silicon/Pitch composites showed high cycle stability at a graphite/silica/pitch ratio (1:4:8 wt%). When the electrode is prepared using PAA binder, the high capacity and stability is obtained. The coin type half cell assembled using EC: DMC: EMC electrolyte showed high initial capacity (719 mAh/g) and excellent cycle stability. The rate performance has an capacity retention (77%) at 2 C/0.1 C and an capacity recovery (88%) at 0.1 C / 0.1 C when the vinylene carbonate (VC) was added.