• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.9
• /
• pp.581-586
• /
• 2015

We studied optical and electrical properties of two-wavelength white tandem organic light-emitting diodes using red and blue materials. White fluorescent OLEDs were fabricated using Alq3 : Rubrene (3 vol.% 5 nm) / SH-1 : BD-2 (3 vol.% 25 nm) as emitting layer (EML). White single fluorescent OLED showed maximum current efficiency of 9.7 cd/A, and tandem fluorescent OLED showed 18.2 cd/A. Commission Internationale de l'Eclairage (CIE) coordinates of single and tandem fluorescent OLEDs was (0.385, 0.435), (0.442, 0.473) at $1,000cd/m^2$, respectively. White hybrid OLEDs were fabricated using SH-1 : BD-2 (3 vol.% 10 nm) / CBP : $Ir(mphmq)_2(acac)$ (2 vol.% 20 nm) as EML. White single hybrid OLED showed maximum current efficiency of 7.8 cd/A, and tandem hybrid OLED showed 26.4 cd/A. Maximum current efficiency of tandem hybrid OLED was more twice as high as single OLED. CIE coordinates of single hybrid OLED was (0.315, 0.333), and tandem hybrid OLED was (0.448, 0.363) at $1,000cd/m^2$. CIE coordinates in white tandem OLEDs compared to those for single OLEDs observed red shift. This work reveals that stacked white OLED showed current efficiency improvement and red shifted emission than single OLED.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.11
• /
• pp.968-972
• /
• 2008

Ni/Ti/Al multilayer system ('/'denotes the deposition sequence) was tested for low-resistance ohmic contact formation to Al-implanted p-type 4H-SiC. Ni 30 nm / Ti 50 nm / Al 300 nm layers were sequentially deposited by e-beam evaporation on the 4H-SiC samples which were implanted with Al (norminal doping concentration = $4\times10^{19}cm^{-3}$) and then annealed at $1700^{\circ}C$ for dopant activation. Rapid thermal anneal (RTA) temperature for ohmic contact formation was varied in the range of $840\sim930^{\circ}C$. Specific contact resistances were extracted from the measured current vs. voltage (I-V) data of linear- and circular transfer length method (TLM) patterns. In constrast to Ni contact, Ni/Ti/Al contact shows perfectly linear I-V characteristics, and possesses much lower contact resistance of about $2\sim3\times10^{-4}\Omega{\cdot}cm^2$ even after low-temperature RTA at $840^{\circ}C$, which is about 2 orders of magnitude smaller than that of Ni contact. Therefore, it was shown that RTA temperature for ohmic contact formation can be lowered to at least $840^{\circ}C$ without significant compromise of contact resistance. X-ray diffraction (XRD) analysis indicated the existence of intermetallic compounds of Ni and Al as well as $NiSi_{1-x}$, but characteristic peaks of $Ti_{3}SiC_2$, a probable narrow-gap interfacial alloy responsible for low-resistance Ti/Al ohmic contact formation, were not detected. Therefore, Al in-diffusion into SiC surface region is considered to be the dominant mechanism of improvement in conduction behavior of Ni/Ti/Al contact.

• Korean Journal of Materials Research
• /
• v.3 no.5
• /
• pp.546-552
• /
• 1993

본 연구에서는 입계의 성질을 이용한 PTCR 재료에 입계 modifier로서 $Bi_{2}$$O_{3}$와 BN을 첨가하고 입계의 미세구조와 결함농도를 변화시켜 이에 따른 소결 및 전기적 특성변화를 TMA, XRD, 복합 임피던스방법 등을 이용하여 해석하였다. 실험 결과 Y이 도우핑된 BaT$iO_{3}$ PTCR 재료에 $Bi_{2}$$O_{3}$를 첨가하였을때 약 0.1mol%까지 고용이 되는 것으로 밝혀졌다. $Bi_{2}$$O_{3}$를 고용한계 이하로 첨가시에는 생성되는 vacancy등의 결함으로 말미암아 Y-BaT$iO_{3}$의 치밀화가 촉진되었으나, 그 이상 첨가하면 치밀화 뿐만 아니라 결정립 성장도 억제되었다.$Bi_{2}$$O_{3}$ 결정립 내부에 Ba와 Ti vacancy가 동시에 생길 수 있어 고온저항이 높아짐을 알 수 있었다. BN은 BaT$iO_{3}$에 고용이 되지 않는 것으로 밝혀졌으며 $B_{2}$O/wub/3를 주성분으로한 액상형성으로 인하여 저온에서의 급격한 치밀화가 관찰되었다. 또 Ba-Y-Ti-B-O의 비정질 상이 tripie junction에 존재함으로서 상온저항이 크게 변화하였으며, PTCR jump도 높아졌다.

• Prospectives of Industrial Chemistry
• /
• v.21 no.1
• /
• pp.3-18
• /
• 2018

전자피부(Electronic skin)는 외부 환경과의 상호작용하는 인간 피부의 기능을 대체하여 외부 자극 신호를 전기적 신호로 변환하는 센서들로 이루어진 인공피부로써, 최근 인간과 전자기기 간의 인터페이스에 대한 관심이 급증하면서 이에 대한 많은 연구들이 진행되고 있다. 그중에서도 피부의 주된 기능인 외부 물리적 자극을 인지하는 촉각을 모방하는 촉각센서는 많은 발전을 거쳐 왔으며, 한계를 극복하고자 다양한 연구들이 진행되고 있다. 촉각센서는 압력, 인장, 굽힘과 같은 물리적 자극에 반응하며, 물리적 자극 신호를 아날로그 및 디지털 신호로 변환하여 인지하는 연구들이 폭넓게 개발되고 있다. 또한, 소자의 구조에 따라 물리적 자극을 전달하는 다양한 변환 방식들이 있으며, 최근에는 각 신호 변환 방식의 민감도, 반응속도, 자극 인지 범위 등의 한계점을 극복하고, 소재의 기계적 물성을 향상시키기 위해 소재의 변형을 주거나 생체의 기관 구조 및 외부 자극 인지 원리 등을 모사한 연구들이 많은 관심을 받고 있다. 본 기고에서는 이러한 촉각센서의 물리적 자극 신호 변환 방식과 소재 변형 및 생체 모사를 통한 다양한 연구들을 소개하고자 하며, 이를 통하여 촉각센서의 나아갈 방향을 제시하고자 한다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.107-108
• /
• 2022

In recent years, the construction industry has a tendency to increase of high-rise builidngs. High rise buildings can use limited space efficiently. But High rise buildings have problem that have extremely heavy weight. Various studies are being conducted to reduce the weight of buildings. Although lightweight aggregate is a meterial that can effectively reduce the weight of buildings, the strength of the aggregate itself is weak and the absorption rate is high, so the strength of the ITZ(Interfacial Transition Zone) area is weak. Therefore, it is essential to improve the interfacial area when using lightweight aggregates. In this study, an experiment was conducted to improve the adhesion between the aggregate and cement paste and to strengthen the interfacial area by coating the surface of the lighteight aggregate with Blast Furnace Slag. To confirm the improvement, compressive strength and EIS(Electrochemical Impedance Spectroscopy) measurements were perfromed. Using EIS, the change in electrical resistance of the cement hardened body was confirmed. As a result, it was confirmed that the lightweight aggregate coated on the surface showed highter compressive strength and electrical resistance than the non-coated lightweight aggregate, and that the coating material was filled in the interfacial area and inside the aggregate that helped to strengthen the compresssive strength and higher electrical resistance.

• The Journal of the Acoustical Society of Korea
• /
• v.26 no.6
• /
• pp.276-285
• /
• 2007

In this paper it was discussed and compared measured loudspeaker impedance curve with ones reconstructed by TS parameters estimated using four kinds of parameter estimation methods developed in frequency domain. Frequency dependent parameters were introduced and derived using least square error minimization technique. For known dynamic mass TS parameter estimation methods were reviewed and also proved non-uniqueness of these parameters by simulation method. Minimum phase transformation was adopted to derive phase information from magnitude of loudspeaker electrical impedance curve measured by one channel analyzer.

• Journal of the Economic Geographical Society of Korea
• /
• v.10 no.4
• /
• pp.355-376
• /
• 2007

The aim of this study is to examine the changes of approach methods of research framework in the history of Korean economic geography during the last fifty years($1956{\sim}2005$). The five factors that have influenced Korean economic geography are Korean geography, European, American, and Japanese geography, fundamental theories of economics and business administration, regional problems, and culture. The study of Korean economic geography can be divided into four periods: 'period of cradle of economic geography($1956{\sim}1962$)', 'period of establishment of economic geography(1963$\sim$later 1970s)', 'period of leap of economic geography(the former half of 1980s$\sim$the former half of 1990s)', and 'period of transition of economic geography (since later 1990s)'. And research framework of Korean economic geography has changed from the regional structure theory in 'period of leap' to the spatial system of economies and network theory in 'period of transition'. Spatial system of economies and network theory consists of spatial system of world economies, spatial system of national economies, spatial system of regional economies, spatial network of enterprise economies, and spatial network of information economies.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.11
• /
• pp.704-710
• /
• 2015

We studied white organic light-emitting diodes using blue fluorescent and red phosphorescent materials. White single OLEDs were fabricated using SH-1 : BD-2 (3 vol.%) and CBP : $Ir(mphmq)_2(acac)$ (2 vol.%) as emitting layer (EML). The white single OLED using SH-1 : BD-2 (3 vol.% 8 nm) / CBP : $Ir(mphmq)_2(acac)$ (2 vol.% 22 nm) as emitting layer showed maximum current efficiency of 8.8 cd/A, Commission Internationale de l'Eclairage (CIE) coordinates of (0.403, 0.351) at $1,000cd/m^2$, and variation of CIE coordinates with ($0.402{\pm}0.012$, $0.35{\pm}0.002$) from 500 to $3,000cd/m^2$. The white tandem OLED using SH-1 : BD-2 (3 vol.% 12 nm) / CBP : $Ir(mphmq)_2(acac)$ (2 vol.% 18 nm) showed maximum efficiency of 19.6 cd/A, CIE coordinates of (0.354, 0.365) at $1,000cd/m^2$, and variation of CIE coordinates with ($0.356{\pm}0.016$, $0.364{\pm}0.002$) from 500 to $3,000cd/m^2$. Maximum current efficiency of the white tandem OLED was more twice as high as the single OLED. Our findings suggest that tandem OLED was possible to produce improved efficiency and excellent color stability.

• Journal of Korean Society of Water and Wastewater
• /
• v.28 no.4
• /
• pp.473-478
• /
• 2014

Microalgae is known as one alternative energy source of the fossil fuel with the small size of $5{\sim}50{\mu}m$ and negative charge. Currently, the cost of microalgae recovery process take a large part, about 20 - 30% of total operating cost. Thus, the microalgae recovery method with low cost is needed. In this study, the optimum current for Scenedesmus dimorphus recovery process using electrocoagulation techniques was investigated. Under the electrical current, Al metal in anode electrode is oxidized to oxidation state of $Al^{3+}$. In the cathode electrode, the water electrolysis generated $OH^-$ which combine with $Al^{3+}$ to produce $Al(OH)_3$. This hydroxide acts as a coagulant to harvest microalgae. Before applying in 1.5 L capacity electrocoagulation reactor, Scenedesmus dimorphus was cultured in 20 L cylindrical reactor to concentration of 1 OD. The microalgae recovery efficiency of electrocoagulation reactor was evaluated under different current conditions from 0.1 ~ 0.3 A. The results show that, the fastest and highest recovery efficiency were achieved at the current or 0.3 A, which the highest energy efficiency was achieved at 0.15 A.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.9
• /
• pp.696-700
• /
• 2010

We fabricated red and blue organic light emitting display (OLEDs) which had the two kinds of multi-structure of ITO/HIL/HTL/EML/ETL/LiF/Al and ITO/HIL/HTL/EML/ETL/LiF/Al/LiF. In the case of red OLED that had LiF/Al/LiF structure compared to LiF/Al structure, the current density increased from 4.3 mA/$cm^2$ to 7.3 mA/$cm^2$, and the brightness increased from 488 cd/$m^2$ to 1,023 cd/$m^2$ at 7.0 V, and as a result the current efficiency was improved from 11.28 cd/A to 13.95 cd/A. Also in the case of blue OLED that had LiF on Al cathode layer, the current density increased from 1.2 mA/$cm^2$ to 1.8 mA/$cm^2$, and the brightness increased from 45 cd/$m^2$ to 85 cd/$m^2$ at 7.0 V, and as a result the current efficiency was improved from 3.69 cd/A to 4.82 cd/A. Through these experimental results it could be suggested that the LiF layer formed on Al prevents the oxidation of Al surface, and the electrode resistance become low with increase of supplied electrons, therefore the brightness and the efficiency are improved from the influence to the well-balanced bonding of electron and hole at emitting layer.