• Journal of KSNVE
• /
• v.8 no.2
• /
• pp.260-266
• /
• 1998

According to the conventional method of analysis for the seismic sliding of equipment submerged in a pool, in general, only the initial condition of fluid gap is used to estimate the hydrodynamic effect between the two structures throughout the seismic analysis. This is based on the assumption of small displacement relative to the fluid gap thickness during earthquakes. In a narrow fluid gap condition, however, this method may lead to a result of unconservative side. Through example seismic analyses for equipment submerged in a pool of a building, in this paper, it is studied when and how much the sliding response can be underestimated. And method of updating the hydrodynamic effect in each step of time integration is proposed to avoid excessive error in estimation of peak sliding response in such a case.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.9
• /
• pp.62-71
• /
• 2002

An intergral C-V converter is proposed to solve the nonlinearity problem of capacitive pressure sensors. The integral C-V converter consists of a switched-capacitor integrator and a switched-capacitor differential amplifier. It converts the sensor capacitance change which is inversely proportional to an applied pressure into a linear voltage output. Various PSPICE simulations prove that the convertor has excellent characteristics, such as low nonlinearity less than 0.01%/FS and low sensitivity to parallel offset capacitance and parasitic capacitance for the displacement range of sensor diaphragm set to 0 ${\sim}$ 90% of the initial distance between the electrodes in the simulation. We also show that the offset compensation and the gain trimming are easily achieved with the integral C-V converter.

• Journal of Chest Surgery
• /
• v.34 no.2
• /
• pp.111-117
• /
• 2001

배경: 심근 수축력과 더불어 전신저항은 개심술 후 적절한 심박출량을 유지하기 위한 매우 중요한 요인이다. 후부하의 변화를 비관혈적으로 평가할 수 있는지 알아 보고자 대동맥 혈류파형의 변화를 관찰하였다. 대상 및 방법: 개흉한 8마리의 잡견에서 연속파형 Doppler 심초음파를 이용하여 nitroprusside 단독 또는 epinephrine과의 병합투여 잔후로 상행 대동맥 혈류를 측정하였다. 결과: Nitroprusside의 투여로 동맥압과 전신저항은 약물의 투여량에 비례하여 감소함으로써(p<0.05 vs 기준치), 대동맥 혈류파형의 최고속도, 평균가속 및 분거리(속도시간적분$\times$심박동수)는 증가하였고, 가속시간은 짧아졌으며(p<0.05 vs 기준치), 가속시간/박출시간의 비는 변화가 없었다. Nitroprusside 투여로 인한 전신저항의 변화는 속도시간적분이나 Doppler 시간간격 지표보다는 최고속도(r=0.60, p=0.001)와 평균가속(r=0.52, p=0.003)과 상관관계가 있었다. Epinephrine과의 병합투여로 전신저항이 증가하지 않는 한 nitroprusside 단독투여에 비해서 최고속도, 평균가속 및 속도시간적분이 더 크게 증가했으나, 전신저항이 증가되면 이 Doppler 지표들은 감소하는 경향을 보였다. 결론: Doppler 심초음파를 이용하여 상행 대동맥 혈류파형의 최고속도와 평균가속을 연속적으로 측정함으로써 후부하의 변화를 비관혈적으로 평가할 수 있으리라 생각된다.

• The KIPS Transactions:PartA
• /
• v.11A no.5
• /
• pp.401-406
• /
• 2004

Among many algorithms for the integration problems in which one wants to compute the approximation to the definite integral in the average case setting, we study the average case errors of numerical integration rules using interpolation. In particular, we choose the composite Newton-Cotes quadratures and the function values at equally spaced sample points on the given interval as information. We compute the average case error of composite Newton-Cotes quadratures and show that it is minimal(modulo a multiplicative constant).

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.518-519
• /
• 2008

전력계통에 FACTS, HVDC등의 전력전자 설비들이 도입되면서 실효치기반의 모의중심이었던 계통해석에 순시치기반의 모의를 사용하고자 하는 노력이 계속되어 왔지만 짧은 적분간격과 소자단위 모델링, 초기화의 어려움 등으로 인해 전력계통해석 중심의 어플리케이션에 적용하기에는 상대적으로 제약이 많았다. 본 논문에서는 상용 전자기과도현상 모의프로그램을 이용해 전력전자설비를 포함하는 전력계통을 보다 상세히 모델링하여 모의할 수 있는 방법을 제안하고자 한다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.11
• /
• pp.1111-1117
• /
• 2008

During the dynamic analysis of a system, the Coulomb friction law is emploved to calculate the friction force. Since the static friction coefficient is only employed during the zero relative velocity, it is impractical to employ the coefficient during the dynamic analysis. To calculate the static friction force, therefore, some friction models have been developed. In this study, the integration stability and the accuracy of the models are investigated with some numerical examples. The effect of time step size during the numerical integration is also investigated. The numerical study shows that the friction model employed for most commercial codes is not as good as the one proposed in this study.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.2
• /
• pp.164-170
• /
• 2004

Liquid Injection Nozzle(LIN) tube and Calandria tube(CT) in pressurized Heavy Water Reactor (PHWR) are .ross-aligned horizontally. These neighboring tubes can contact each other due to the sag of the calandria tube resulting from the irradiation creep and thermal creep, and fuel load, etc. In order to judge the contact which might be the safety concern, the remote field eddy current (RFEC) technology is applied for the gap measurement in this paper. LIN can be detected by inserting the RFEC probe into pressure tube (PT) at the crossing point directly. To obtain the optimal conditions of the RFEC inspection, the sensitivity, penetration and noise signals are considered simultaneously. The optimal frequency and coil spacing are 1kHz and 200mm respectively. Possible noises during LIN signal acquisition are caused by lift-off, PT thickness variation, and gap variation between PT and CT. The simulated noise signals were investigated by the Volume Integral Method(VIM). Signal analysis on the voltage plane describes the amplitude and shape of LIN and possible defects at several frequencies. All the RFEC measurements in the laboratory were done in variance with the CT/LIN gap and showed the relationship between the LIN gap and the signal parameters by analyzing the voltage plane signals.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.37 no.1
• /
• pp.9-16
• /
• 2024

Using the proper orthogonal decomposition (POD) based intrusive reduced order model (ROM), the total degrees of freedom of the structural system can be significantly reduced and the critical time step satisfying the conditional stability increases in the explicit time integrations. In this study, therefore, the changes in the critical time step in the explicit time integrations are investigated using both the POD-ROM and Voronoi-cell lattice model (VCLM). The snapshot matrix is composed of the data from the structural response under the arbitrary dynamic loads such as seismic excitation, from which the POD-ROM is constructed and the predictive capability is validated. The simulated results show that the significant reduction in the computational time can be achieved using the POD-ROM with sufficiently ensuring the numerical accuracy in the seismic analyses. In addition, the validations show that the POD based intrusive ROM is compatible with the Voronoi-cell lattice based explicit dynamic analyses. In the future study, the research results will be utilized as an elemental technology for the developments of the real-time predictive models or monitoring system involving the high-fidelity simulations of structural dynamics.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.4
• /
• pp.190-200
• /
• 1996

Step-by-step time integration methods are widely used for solving structural dynamics problem. One difficult yet critical choice an analyst must make is to decide an appropriate time step size. The choice of time step size has a significant effect on solution accuracy and computational expense. The objective of this research is to derive error estimate for newly developed time integration method and develop automatic time step size control algorithm for structural dynamics. A formula for computing error tolerance is derived based on desired period resolution. An automatic time step size control strategy is proposed based on a normalized local error estimate for the generalized-α method. Numerical examples demonstrate the developed strategy satisfies general design criteria for time step size control algorithm for dynamic problem.

• Journal of the Korean Magnetics Society
• /
• v.3 no.2
• /
• pp.121-124
• /
• 1993

보자력이 큰 강자성체의 자기이력곡선, 자기변형, 자기이방성등의 측정에 사용할수 있는 펄스전자석을 설계제작하였다. 철심의 형상이 주어졌을때 권선의 회수에 따른 전자석의 여러특성과 축전기 방전시의 전류진폭 감쇄비등을 계산하는 일반식을 유도하고 그것에 의하여 철심단면적 46 nm * 32 nm, 공기간격 28nm의 전자석을 설계 제작하여 20 mT/A의 기울기로 0.49 T까지 직선적인 자기장 대 전류특성을 얻었다. 이 전자석에 에너로그 적분기에 의한 자속계를 부쳐서 박막 또는 박대시료의 major 및 minor 이력곡선을 단번에 쉽게 얻을 수 있는 자기이력곡선 측정기가 구성되었다.