• 대한방사선방어학회:학술대회논문집
• /
• 2011.04a
• /
• pp.14-15
• /
• 2011

• Geophysics and Geophysical Exploration
• /
• v.11 no.4
• /
• pp.326-334
• /
• 2008

The resistivity method has been used to image the electrical properties of the subsurface. Especially, this method has become suitable for monitoring since data could be rapidly and automatically acquired. In this study, we developed a time-lapse inversion algorithm for the interpretation of resistivity monitoring data. The developed inversion algorithm imposes a big penalty on the model parameter with small change, while a minimal penalty on the model parameter with large change compared to the reference model. Through the numerical experiments, we can ensure that the time-lapse inversion result shows more accurate and focused image where model parameters have changed. Also, applying the timelapse inversion method to the leakage detection of an embankment dam, we can confirm that there are three major leakage zones, but they have not changed over time.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.3
• /
• pp.284-291
• /
• 2002

An attempt was made to evaluate the degree of aging degradation in thermally aged 2.25Cr-1Mo steel by electrical resistivity measurement. Artificial aging was performed to simulate the microstructural degradation in 2.25Cr-1Mo steel arising from long time exposure at $540^{\circ}C$. Microstructural parameter (amount of solid solution element), mechanical property (ductile-brittle transition temperature) and electrical resistivity were measured to investigate the mutual relationship among these parameters. Depletion of solid solution element(Mo and Cr) in matrix was detected after aging. The ductile-brittle transition temperature(DBTT) increased rapidly in the initial stage of aging and then saturated afterward. On the other hand, the electrical resistivity decreased rapidly in the beginning and then saturated in the later stage of aging.

• Journal of Energy Engineering
• /
• v.23 no.4
• /
• pp.189-195
• /
• 2014

The use of solar energy among renewable energy tends to increase because of its infinity and cleanness of resources. Even though the consumption rate of solar energy in our country is still low, however, in recent years, the research for solar energy have been widely conducted due to policy support of government. This study was performed to investigate the efficiency of heat collection using solar collector with single evacuated tube-type. As the results, the temperature of radiation fin for solar collector with single evacuated tube-type was lower in spite of high temperature of heat pipe compared that of double evacuated tube-type. In order to increase the efficiency of heat collection, it was confirmed that the loss of heat collection due to contact resistance as well as performance improvement for solar collector should be decreased.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.130-130
• /
• 2003

일반적으로 Indium tin oxide (ITO)는 유기EL 소자 제작 공정에서 필수 불가결한 물질로 알려져 있다. ITO는 정공 수송의 기능을 하게 되는데 정공 주입의 효율을 향상시키기 위해서는 ITO 표면의 저 저항화와 ITO/유기박막 접합계면의 일함수 값의 적절한 균형이 중요하다. 그리고 현재 플라즈마를 이용한 ITO 기판의 세정은 산소 래디칼을 이용하여 표면을 산화하는 방식인 산소 플라즈마를 이용한 세정 방법이 널리 이용되고 있다. 본 연구에서는 ITO 표면의 탄소 오염물을 제거하여 저항특성을 향상시키기 위하여 원거리 산소와 수소 플라즈마 세정을 적용하였고, 그에 따른 탄소를 포함하는 오염물의 제거 효율과 산소와 수소 플라즈마로 처리된 ITO 표면의 특징을 기술하였다. 실험에 사용된 플라즈마 소스는 radio-frequency(RF) 플라즈마이고, 원거리 플라즈마 세정 시스템과 표면 분석 장비인 X-ray photoelectron spectroscopy(XPS)가 in-situ로 연결되어 있는 진공장비로 분석을 하였다 플라즈마 세정 전에 전처리 세정을 시행하지 알았으며, 세정 후 in-situ XPS에 의해서 화학 조성 및 결합 구조의 변화를 분석하였다. 또한 일함수와 면저항 값을 측정하고 그에 따른 표면의 저항 특성 및 표면 전위에 관하여 세정 효율과 연관지어 해석하였다. 원거리 산소/수소 플라즈마 세정 후 ITO 표면의 탄소오염물이 검출한계 이하로 효과적으로 제거된 것을 in-situ XPS 분석 결과로 확인하였고, 플라즈마 처리 순서 및 플라즈마 파워를 변화하여 그에 따른 표면의 결합 상태 및 화학 조성의 변화를 비교 분석하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.11
• /
• pp.2495-2502
• /
• 2012

This paper presents a new structure of phase looked loop (PLL) for replacing a process sensitive resistor in loop filter with an additional charge pump (CP). The additional charge pump works as a resistor in a loop filter. The output of two charge pumps changes same direction according to process variation. The simulation results according to process conditions(SS/TT/FF) demonstrate that the proposed PLL works properly with process variations. It has been designed with a 1.8V $0.18{\mu}m$ CMOS process and proved by simulation with HSPICE.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.10
• /
• pp.2247-2252
• /
• 2012

In this paper, we produced CIGS thin film by co-evaporation method. During the process, substrate temperature and Ga/(In+Ga) composition ratio was altered to observe the change of resistivity and absorbance spectra measurements. As substrate temperature increased, resistivity decreased and as Ga/(In+Ga) composition ratio increased from 0.30 to 0.72, band gap also increased with the range of 1.26eV, 1.30eV, 1.43eV, 1.47eV. With the constant condition of composition ratio, resistivity decreased with increased thickness of the thin film. On this experiment, we assumed that optical absorbance ratio and optical current will be increased with CIGS thin film fabrication.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.6
• /
• pp.16-23
• /
• 2003

In this paper, we propose an efficient bias circuit of discrete BJT component for hearing aid. The collector feedback bias circuit, widely used for the hearing aid, has a resistor for negative feedback. As the resistor affects AC and DC simultaneously, it is quite difficult to adjust amplifier gain without changing DC bias point. The previous bias circuit also has weak point to be oscillated by the positive feedback of power noise if gain of hearing aid is high. In the proposed circuit, we can reduce the two weak points of the previous circuit by adding a resistor to the collector feedback bias circuit between base and power supply which is $\beta$ times target than the collector resistor. Thus. we can change amplifier gain without changing DC bias point, and reduce power noise gain about 18.5% compare to that of tile previous circuit in the simulation.

• Resources Recycling
• /
• v.17 no.5
• /
• pp.19-27
• /
• 2008

In this study, the porosity and electrical resistivity of the formed coke produced by sintering the mixture of domestic anthracite and phenolic resin were mainly investigated, when the effect of the amount of binder, the hydration temperature and time, the hardening temperature and time, sintering temperature and time, the particle size of anthracite, the grade of anthracite, and the mixing ratio of phenolic resin on the physical properties of the coke were studied. As a result, It was found that the electrical resistivity and porosity of the formed coke are varied in the range of $0.3\sim1.2\Omega{\cdot}cm$ of $10\sim30%$, respectively, in accordance with the variation of factors.

• Food Science and Preservation
• /
• v.6 no.4
• /
• pp.424-428
• /
• 1999

The performance of a 30K polysulfone membrane for clarification of depectinized peach juice was studied Ultrafiltration of peach juice could minimize to loss of flavor and many compounds and was expected to effectively remove precipitation and suspended solid. The results showed that permeate flux increased with the increase of operating pressure and temperature. The permeate flux declined continuously as the process time increased. The values of soluble solid and titratable acidity of permeate were decreased or were at the same level, the turbidity was largely decreased. Total resistance decreased with lower temperature and lower pressure.