• Korean Chemical Engineering Research
• /
• v.59 no.4
• /
• pp.542-547
• /
• 2021

Glass lined impellers are corrosion resistant to most chemicals, including strong acids, and also have a smooth, non-stick surface, easy to clean and free from impurities in the process. Glass lined home base impeller is a multi-purpose impeller designed to stir a wide viscosity range of liquids from low viscosity fluids to high viscosity fluids, among others, cell culture, yeast culture, and beer fermentation pots, especially used for air-water system breathable stirring. The glass lining for HB impellers, which are simple in structure and competitive in performance, is essential to have upper and lower division in order to make the joint area between the impeller and shaft as small as possible. The upper and lower division of the impeller hardly affects the mixing performance, but the aeration performance. In this study, in order to optimize the shape of the Glass Lining HB impeller, a study was conducted on the effect of the angle between the upper and lower impellers, the clearance between the impellers, and the number of baffles on the aeration power. The optimal shape and baffle plate conditions for the Glass lined HB impeller were derived through the study results that the angle and the clearance between the upper and lower impellers decreased the ration of the power consumption with aeration P_g and that without aeration P₀, P_g/P₀.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.46 no.1
• /
• pp.1-9
• /
• 2019

The aim of this study was to compare the degree of conversion and polymerization shrinkage of low and high viscosity bulk-fill giomer-based and resin-based composites. Two bulk-fill giomer (Beautifil Bulk Restorative (BBR), Beautifil Bulk Flowable (BBF)), two bulk-fill (Tetric N-Ceram Bulk-fill (TBF), SureFil SDR flow (SDR)) and two conventional resin composites (Tetric N-Ceram (TN), Tetric N-flow (TF)) were selected for this study. The degree of conversion was measured by using Fourier transform infrared spectroscopy. Polymerization shrinkage was measured with the linometer. For all depth, BBR had the lowest degree of conversion and SDR had the highest. At 4 mm, the degree of conversion of low and high viscosity bulk-fill giomer resin composites was lower than that of bulk-fill resin composites (p < 0.05). At the depth between 2 mm and 4 mm, there were significant difference with TBF, TN and TF (p < 0.05), while no significant difference in the degree of conversion was measured for BBR, BBF and SDR. Polymerization shrinkage of six resin composites decreased in the following order: TF > SDR > BBF > TBF > TN and BBR (p < 0.05). Polymerization shrinkage of bulk-fill giomer resin composites was lower than that of bulk-fill resin composites (p < 0.05). From this study, it is found that the bulk-fill giomer resin composites and TBF were not sufficiently cured in 4 mm depth. The degree of conversion of low and high viscosity bulk-fill giomer resin composites was significantly lower than bulk-fill resin composites in both 2 mm and 4 mm depths. Therefore, such features of bulk-fill giomer resin composites should be carefully considered in clinical application.

• Polymer(Korea)
• /
• v.29 no.6
• /
• pp.565-570
• /
• 2005

Melt processing characteristics of nylon 6 (N6) has been investigated by controlling the melt viscosity in melt impregnation process. Calcium stearate (CaST) was introduced as a lubricant for N6 and the melt viscosity of N6 decreased with adding only 1 wt$\%$ of CaST. In addition, reactive blending with polycaprolactone (PCL) was carried out by lowering the melt viscosity in N6. It was found that the melt viscosity of N6 could be controlled and further melt viscosity drop could be obtained by applying phenyl phosphite (PP) and diphenyl phosphite (DPP) to enhance the transesterification between N6 and PCL. Our approaches show that the melt viscosity of N6 could be reduced without loss of thermal stability which is the critical problem in high temperature melt impregnation process of N6.

• Tribology and Lubricants
• /
• v.5 no.2
• /
• pp.7-20
• /
• 1989

합성윤활유(synthetic lubricant)라 함은 현재까지도 계속되고 있는 광유(mineral oil) 전성시대의 광유에 대응되는 말로써 광유계 윤활유로 부터 얻기 어려운 높은 점도지수, 우수한 저온 유동성 등의 특성을 얻기 위해 유기합성방법에 의해 인위적으로 제조한 윤활유의 총칭이며 작용기의 종류, 합성방법, 등에 따라 다양하게 분류된다. 합성윤활유의 종류에는 합성방법에 따라 폴리머형(P형), 비폴리머형(N형)으로 대별되는데, 폴리머형 합성유에는 poly-butene, poly-$\alpha$-olefin, Polyalky lenglycol, Silicon oil, Chlorofluorocarbon, Perfiuoroalkylpolyether 등이 있으며, 비폴리머형 합성유에는 Alkylbenzene, Dibasicacidester, Polyolester, Silicate-ester Polyphenylether, Complex ester 등이 포함된다. 전자의 경우에는 중합반응 조건을 조절하므로써 여러점도 등급의 합성유들을 얻을 수 있는 반면 후자의 경우에는 분자량이 크지 않으므로 저점도의 것만 얻어지는 것이 특징이다.

• Journal of Adhesion and Interface
• /
• v.10 no.4
• /
• pp.174-181
• /
• 2009

The viscosity for hi-solid pressure sensitive adhesive to improve water soluble low viscosity pressure sensitive adhesive polymerized using seeded polymerization. While seed binder polymerizing it produces an optimum polymerization condition, and acrylic acid and seed binder concentration changed were measurement of viscosity variation and adhesive power at the substrate (SUS420J) as flowing results. In adhesive polymerization, seed binder concentration 7 wt%/monomer was recovered 60% of solid content, 2,100 cps of low viscosity and clear adhesive film. When acrylic acid content was 4 wt%/monomer, it was turned excellent adhesive power and holding power.

• Journal of ILASS-Korea
• /
• v.9 no.3
• /
• pp.1-7
• /
• 2004

This experiment was undertaken to investigate the atomization characteristics of the low viscosity biodiesel blended fuel and ultrasonic energy added one. Test fuels were conventional diesel fuel and biodiesel fuel. We compared to the characteristics of viscosity and surface tension, SMD between low viscosity biodiesel blended fuel and ultrasonic energy added one. Sauter mean diameter was measured under the variation of the spray distance. Viscosity and surface tension was measured under the variation of the time trace. To measure the droplet size, we used the Malvern system 2600C. Droplet size distribution was analyzed from the result data of Malvern system. Through this experiment, we found that the condition of the ultrasonic energy added situation had smaller Sauter mean diameter of droplet, viscosity and surface tension than that of the conventional situation.

• Magazine of RCR
• /
• v.17 no.3
• /
• pp.8-11
• /
• 2022

• The Journal of the Korea Contents Association
• /
• v.15 no.1
• /
• pp.324-330
• /
• 2015

When diagnostic ultrasounds are used, an ultrasonic transmission media is used to effectively transmit the ultrasonic energy. Types of ingredients of polymer hydro gel, emulsion, and oil gel were compared with commercialized products by measuring characteristics of ultrasonic transmission media such as skin lubricity, skin moisturizing, and dryness speed which were contained in each different media. The mean friction coefficient measured to investigate skin lubricity showed high in the agent containing a large amount of oil, whereas the mean friction coefficient of the low viscosity emulsion did not show a significant difference with that of the polymer hydro gel. The moisture evaporation measured to investigate the dryness speed of the agent showed highest in polymer hydro gel. This showed that the larger amount of oil it had, the less moisture evaporation occurred. For skin moisture measured to investigate moisturizing characteristics of skin, low viscosity emulsion showed high in moisture content, whereas it showed slowest reduction in moisture content. As a type of emulsion appropriately containing water and oil is superior in skin moisturizing and skin tenderness, it is expected to serve as a dosage form of new ultrasonic transmission media.

• Journal of ILASS-Korea
• /
• v.10 no.4
• /
• pp.8-15
• /
• 2005

The use of clean gaseous fuels for the purpose of high efficiency and low emission in automotive engines has tendency to increase in order to meet the reinforcing emission regulations and to efficiently utilize limited natural resources. Automotive companies developed and commercialized a LPG liquid injection system, which is mounted on LPLi(Liquid Phase LPG Injection) engines and vehicles based on this research trend. This research examines the biggest problem in LPLi engine, that is, the leakage characteristics of low viscosity LPG fuel according to the injector design variables. This study is also aimed to improve the performance of fuel-leakage in LPLi engine through the addition of a lubrication improver in HFRR(High Frequency Reciprocating Rig) facility. The needle displacement and the spring displacement of an LPLi injector are found to be already optimized. The possibility of a maximum of 70% leakage reduction compared to a conventional case, is verified when 1000ppm of a lubrication improvement material is added and 40% increase of a injector spring constant (K) is applied.

• Composites Research
• /
• v.33 no.2
• /
• pp.39-43
• /
• 2020

Recently, fabrication process of thermoplastic polyamide-based composites with recyclability as well as impact, chemical, and abrasion resistance have been widely studied. In particular, thermoplastic reactive resin transfer molding (TRTM) in which monomer with low viscosity is injected and in-situ polymerized inside mold has received a great attention, because thermoplastic melts are hard to impregnate fiber preform due to their very high viscosity. However, it is difficult to optimize the processing conditions because of high reactivity and sensitivity to external environments of the used monomer, ε-caprolactam. In this study, viscosity as an important process parameter in TRTM was measured during in-situ anionic polymerization of ε-caprolactam and the solutions for problems caused by high polymerization rate and sensitivity to moisture and oxygen were suggested. Reliability of the improved measurement technique was verified by comparing the viscosity behavior at various environmental conditions including humidity and atmosphere, and it is expected to be helpful for optimization of TRTM process.