• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.4
• /
• pp.307-313
• /
• 2016

When liquefied natural gas (LNG) is stored in a tank, it is necessary to maintain low temperature. It is very important that insulation techniques are applied to the LNG cargo because of this extreme environment. Hence, laminated wood, especially plywood, is widely used as the structural member and insulation material in LNG cargo containment systems (CCS). However, fracture of plywood has been reported recently, owing to sloshing effect. Therefore, it is necessary to increase the strength of the structural member for solving the problem. In this study, compressed wood, which is used as a support in LNG independent type B tanks, was considered as a substitute for plywood. Compression and bending tests were performed on compressed wood under ambient and cryogenic temperatures to estimate the mechanical behaviors and fracture characteristics. In addition, the direction normal to the laminates surface was considered as an experimental variable. Finally, the feasibility of using compressed wood for an LNG CCS was evaluated from the test results.

• Journal of the korean Society of Automotive Engineers
• /
• v.24 no.5
• /
• pp.98-103
• /
• 2002

이제 카트 정렬과 휠 셋업에 필요한 최적의 변수들을 알아보았다. 실제 세팅은 위에서 언급한 내용 이외에도 많은 것들을 고려하여야 한다. 타이어 접지력의 세팅은 경기장, 날씨, 제품의 불 균일성 등을 고려하여 야 한다. 즉, 어떤 경기장은 코너의 반경이 다른 경기 장 보다 크며 어떤 경기장은 코너가 매우 많기도 하여 세팅을 상황에 맞게 하여야 하는 것이다. 각각의 변수를 세팅할 경우는 중간 값을 취하는 것이 바람직하여 이 중간 값을 취하는 것이 바람직하며 이 중간 값을 각각의 경기장의 특성에 맞추어 변화시키면 되는 것이다. 예를 들면, 접지력이 작게 발생되는 경기장(혹은 매우 추운날씨) 에서는 캐스터를 코기 하여 초기 회전 발생이 용이하게 할 수도 있다. 또한 토우인 값을 크게 하여 타이어가 마찰을 더욱 많이 발생하여 타이어의 온도가 급격히 상승하여 원하는 접지력의 수준에 용이하게 도달할 수 있게 하는 것이다. 그러나 이러한 세팅은 다른 핸들링 문제를 야기할 수 있다는 것을 이해하여야 하며 이러한 문제를 해결하는 또 다른 노력이 필요하게 되는 것이다. 가장 중요한 것은 후륜 내측으로부터는 조종 성능을 향상시키는데 필요한 접지력을 거의 기대하지 못한다는 것이며 마찰이 적게 발생하여 손쉽게 동력 손실을 초래하고 있다는 것이다. 그러므로 회전을 할 경우에도 속도를 낮추어서는 안되며 이렇게 하이야 핸들링이 매우 용이하게 되는 것이다. 그러나 위의 설명에서도 보았듯이 일부 세팅을 변경하면 여러 곳이 그 효과가 나타난다. 예를 들어 후륜의 간격을 변화시키면 카트에서 무게이동 뿐만 아니라 회전 시에 가속이나 감속에 의한 회전 토크의 효과도 달라지게 된다. 특정한 세팅의 변화가 어떻게 작용할 것이라는 확신을 가지고 있다고 할지라도 세팅에서 가장 중요한 것은 주행 기록이다. 여기서 설명되어진 많은 내용이 주행 기록을 향상시키기를 바라는 바이다.간이 육색과 총육색소 함량에는 영향을 미치지 않는 것으로 나타났다. 관능적 특성평가 중 육색과 육즙참출은 대조구와 비교하여 CLA급여 처리구가 유의적인 차이가 없었으나, 근내지방 축적 정도와 전체적인 기호성은 대조구에 비하여 CLA 급여 처리구가 유의적으로 높은 평가를 받았다(p<0.05). 간격은 술 후 1년 후까지도 지속적으로 감소하는 경향을 보였다. 따라서 이 기간동안에는 추적관찰이 필요한 것으로 생각된다.경미하게 나타났으며, 이는 2% 흥국 첨가식이의 섭취로 인한 bromobenzene 대사 및 유해산소 해독의 촉진에 기인되기 때문일 것으로 생각된다.다.과 및 지질과산화억제효과의 순과 일치하였다. 총 flavonoid 함량은 DPPH 라디칼 제거효과에 대한 $IC_{50}$/ 값과 높은 상관관계(r=-0.9924, p<0.01)를 나타내었다.이 우수한 심근보호 효과를 나타내나, 허혈시간이 2시간을 초과하면 심근의 혈역학적 기능과 미세구조의 변화는 중등도의 저온(22∼24$^{\circ}C$)에서 유의하게 악화되었다. 이 같은 결과로 볼 때 심근 허혈시간이 2시간을 초과한다면 심근 온도를 낮추어야 할 것으로 판단된다. 7.2, with 64.0% of office workers having an average level between 6- and 9. The degree of stress was higher for females than males, for unmarried salaried and hot-tempered persons. Those not doing exercise were subject to the highest levels of stress, and those a having sufficient sleep were found to be subject to less stress.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.4
• /
• pp.149-154
• /
• 2018

This paper describes the fabrication and heat transfer property of 50 watts rated LED array module where multiple chips are mounted on chip-on-board type ceramic-metal hybrid substrate with high heat dissipation property for high power street and anti-explosive lighting system. The high heat transfer ceramic-metal hybrid substrate was fabricated by conformal coating of thick film glass-ceramic and silver pastes to form insulation and conductor layers, using thick film screen printing method on top of the high thermal conductivity aluminum alloy heat-spreading panel, then co-fired at $515^{\circ}C$. A comparative LED array module with the same configuration using epoxy resin based FR-4 PCB with thermalvia type was also fabricated, then the thermal properties were measured with multichannel temperature sensors and thermal resistance measuring system. As a result, the thermal resistance of the ceramic-metal hybrid substrate in the $4{\times}9$ type LEDs array module exhibited about one third to the value as that of FR-4 substrate, implying that at least triple performance of heat transfer property as that of FR-4 substrate was realized.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.35 no.2
• /
• pp.93-101
• /
• 1999

A simple experimental method was used in an attempt to realize the elevation of the fishing ability of purse seine in the sea area of Cheju Island, the changes of seine volume and tension in the purseline during pursing. Experiments carried out on the six types simplified reduced model seines which were made of knotless nettings. The nettings were woven in different leg length 4.3, 5.0, 5.5, 6.0, 6.6 and 7.7mm of polyester 28 tex two threads two-ply twine, and each of the seines were named I, II, III, IV, V and Ⅵ seine. Dimension of seine models were 450cm for corkline and 85cmfor seine depth, each seines rigged up 160g of float for a floatline and 50g (underwater weight) of lead for a leadline. These model purse seines were made of the scale of 1/200 of its full scale, a 120 ton in the near sea of Cheju Island. Designing and testing for the model purse seines were based on the Tauti's law. Experiments were measured in the observation channel of a flume tank at the static conditions set up shooting and pursing equipments. Motion of purse seine during purse line was recorded by the two sets video camera for VTR which were placed in top and front of the model seine. The reading coordinate of seine volume carried out by the video digitization system, disk data for the purseline tension. An analysis were performed on the changes seine volume and tension in the purseline during pursing. The results obtained were as follows: 1. The seine volume during pursing was largest for Ⅵ seine with smallest d/l followed by V, IV, III, II and I seines, and tension in the purseline was small. 2. Seine volume during pursing can be expressed by the following equation; CVt=l-EXP[｛2.79 (d/l）＋0.35｝t-33.37 (d/l) ＋ 0.57] Where CVt is volume ratio, d is twine diameter, l is leg length and t is pursing time (sec). 3. Tension in the purse line during pursing can be expressed by the following equation; T= 1- EXP ｛0.57t ＋ 13.36 (d/l)+2.97｝ Where T is tension (kg) in the purseline during pursing.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.264-264
• /
• 2016

최근에 charge trap flash (CTF) 기술은 절연막에 전하를 트랩과 디트랩 시킬 때 인접한 셀 간의 간섭현상을 최소화하여 오동작을 줄일 수 있으며 낸드 플래시 메모리 소자에 적용되고 있다. 낸드 플래시 메모리는 고집적화, 대용량화와 비휘발성 등의 장점으로 인해 핸드폰, USB, MP3와 컴퓨터 등에 이용되고 있다. 기존의 실리콘 기반의 플래시 메모리 소자는 좁은 밴드갭으로 인해 투명하지 않고 고온에서의 공정이 요구되는 문제점이 있다. 따라서, 이러한 문제점을 개선하기 위해 실리콘의 대체 물질로 산화물 반도체 기반의 플래시 메모리 소자들이 연구되고 있다. 산화물 반도체 기반의 플래시 메모리 소자는 넓은 밴드갭으로 인한 투명성을 가지고 있으며 저온에서 공정이 가능하여 투명하고 유연한 기판에 적용이 가능하다. 다양한 산화물 반도체 중에서 비정질 In-Ga-Zn-O (a-IGZO)는 비정질임에도 불구하고 우수한 전기적인 특성과 화학적 안정성을 갖기 때문에 많은 관심을 받고 있다. 플래시 메모리의 고집적화가 요구되면서 절연막에 high-k 물질을 atomic layer deposition (ALD) 방법으로 적용하고 있다. ALD 방법을 이용하면 우수한 계면 흡착력과 균일도를 가지는 박막을 정확한 두께로 형성할 수 있는 장점이 있다. 또한, high-k 물질을 절연막에 적용하면 높은 유전율로 인해 equivalent oxide thickness (EOT)를 줄일 수 있다. 특히, HfOx와 AlOx가 각각 trap layer와 blocking layer로 적용되면 program/erase 동작 속도를 증가시킬 수 있으며 넓은 밴드갭으로 인해 전하손실을 크게 줄일 수 있다. 따라서 본 연구에서는 ALD 방법으로 AlOx와 HfOx를 게이트 절연막으로 적용한 a-IGZO 기반의 thin-film transistor (TFT) 플래시 메모리 소자를 제작하여 메모리 특성을 평가하였다. 제작 방법으로는, p-Si 기판 위에 열성장을 통한 100 nm 두께의 SiO2를 형성한 뒤, 채널 형성을 위해 RF sputter를 이용하여 70 nm 두께의 a-IGZO를 증착하였다. 이후에 소스와 드레인 전극에는 150 nm 두께의 In-Sn-O (ITO)를 RF sputter를 이용하여 증착하였고, ALD 방법을 이용하여 tunnel layer에 AlOx 5 nm, trap layer에 HfOx 20 nm, blocking layer에 AlOx 30 nm를 증착하였다. 최종적으로, 상부 게이트 전극을 형성하기 위해 electron beam evaporator를 이용하여 platinum (Pt) 150 nm를 증착하였고, 계면 결함을 최소화하기 위해 퍼니스에서 질소 가스 분위기, $400^{\circ}C$, 30 분의 조건으로 열처리를 했다. 측정 결과, 103 번의 program/erase를 반복한 endurance와 104 초 동안의 retention 측정으로부터 큰 열화 없이 메모리 특성이 유지되는 것을 확인하였다. 결과적으로, high-k 물질과 산화물 반도체는 고성능과 고집적화가 요구되는 향후 플래시 메모리의 핵심적인 물질이 될 것으로 기대된다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.2
• /
• pp.261-267
• /
• 2017

The interest in biodiesel is increasing rapidly. As a result, the price of vegetable oil that is used as a raw material for biodiesel is skyrocketing. Studies of biodiesel using animal waste as a means of solving these problems are underway. Biodiesel produced from animal fat contains considerably more saturated fatty acids than that produced from vegetable oil. In addition, it has a high cetane number and a high heating value. On the other hand, the fluidity decreases at lower temperatures because of the large amount of saturated fatty acids. For the biodiesel production, waste chicken oil and soybean oil were first purified. The raw materials were mixed at various ratios from 1:9 to 9:1. The methanol / oil molar ratio was also changed from 7 mol to 15 mol. The entire reaction time was one hour. The results showed that the optimal mixing ratio of soybean oil to waste chicken oil was 3:7, and the optimal methanol / oil molar ratio was 13. Moreover, the BD yield was 90.2%, the FAME content was 96.6%, and the LAME content was 4.1%. This result satisfied the Korea Industrial Standard (KSM2413).

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.12
• /
• pp.59-65
• /
• 2004

A stable reference voltage generator is necessary to the infrared image signal readout circuit(ROIC) to improve noise characteristics of signal originated from infrared devices, that is, to gain good images. In this paper, bandgap circuit operating at cryogenic temperature of 77K for Infrared image ROIC(readout integrated circuit) was first made. It demonstrates practical use possibility through taking measurements and estimations. Bandgap circuit is a representative voltage reference circuit. Most of bandgap reference circuits which are presented so far operate at room temperature, and their characteristic are not suitable for infrared image ROIC operating at liquid nitrogen temperature, 77K. To design bandgap circuit operating at cryogenic temperature, suitable circuit is selected and the parameter characteristics of used devices as temperature change are seen by a theoretical study and fitted at liquid temperature with considering such characteristics. This circuit has been fabricated in the Hynix 0.6um standard CMOS process, and the output voltage measured shows that the stability is 1.042±0.0015V over the temperature range of 60K to 110K and is better than bandgap circuits operated at room temperature.

• Journal of Energy Engineering
• /
• v.23 no.2
• /
• pp.28-34
• /
• 2014

Automatic transmission fluid (ATF) is used for automatic transmissions in the vehicle as the characterized fluid. Recently, the vehicle manufacture usually guarantee for fluid change over 80000~100000 km mileage or no exchange, but most drivers usually change ATF below every 50000 km driving in Republic of Korea. It can cause to raise environmental contamination by used ATF and increase the cost of driving by frequently ATF change. In this study, we investigate the various physical properties such as flash point, fire point, pour point, kinematic viscosity, cold cranking simulator, total acid number, and metal component concentration for fresh and used ATF after driving (50000 km, 100000 km). The result showed that the total acid number, pour point, Fe, Al and Cu component had increased than fresh ATF, but 2 kind of used oil (50000 km and 100000km) had similar physical values and metal component concentration.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.43 no.5
• /
• pp.555-566
• /
• 2023

In this study, a composite phase change material (CPCM) produced using the SOL-GEL technique was developed as a thermal energy storage medium for low-temperature applications. Tetradecane and activated carbon (AC) were used as the core and supporting materials, respectively. The tetradecane phase change material (PCM) was impregnated into the porous structure of AC using the vacuum impregnation method, and a thin layer of silica gel was coated on the prepared composite using the SOL-GEL process, where tetraethyl orthosilicate (TEOS) was used as the silica source. The thermal performance of the CPCM was analysed using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). DSC results showed that the pure tetradecane PCM had melting and freezing temperatures of 6.4℃ and 1.3℃ and corresponding enthalpies 226 J/g and 223.8 J/g, respectively. The CPCM exhibited enthalpy of 32.98 J/g and 27.7 J/g during the melting and freezing processes at 7.1℃ and 2.4℃, respectively. TGA test results revealed that the AC is thermally stable up to 500℃, which is much higher than the decomposition temperature of the pure tetradecane, which is around 120℃. Moreover, in the case of AC-PCM and CPCM thermal degradation started at 80℃ and 100℃, respectively. The chemical stability of the CPCM was studied using Fourier-transform infrared (FT-IR) spectroscopy, and the results confirmed that the developed composite is chemically stable. Finally, the surface morphology of the AC and CPCM was analysed using scanning electron microscopy (SEM), which confirmed the presence of a thin layer of silica gel on the AC surface after the SOL-GEL process.

• Korean Chemical Engineering Research
• /
• v.52 no.5
• /
• pp.688-693
• /
• 2014

For investigating NO reduction activity of an catalytic filter, the catalytic performance was measured under the presence of $SO_2$ and $H_2O$, respectively or simultaneously in the simulation gas composed of NO, $NH_3$, and air. The catalytic filter was prepared by coating $V_2O_5-WO_3/TiO_2$ catalyst on the pore surface of SiC filter element of which the superior performance for the particulate removal was well known. At the temperature below $260^{\circ}C$, the catalytic activities were enormously decreased under the presence of $SO_2$ and $H_2O$, respectively or simultaneously, compared with those under the cases of the absence of $SO_2$ and $H_2O$. However, the presence of $SO_2$ promoted the performance of the catalytic filter above $320^{\circ}C$ with showing the NO conversion better than 99.8% for the NO inlet concentration of 500 ppm and at the face velocity of 2 cm/s. In particular, the presence of water showed high NO conversion higher than 99% up to high temperature of $380^{\circ}C$. This effect of water was explained by the reason that it retarded the ammonia oxidation which is the main step into the formation of $N_2O$. The initial NO reduction activity of the catalytic filter maintained for the duration of 100 hours in the presence of $SO_2$ and $H_2O$. Therefore, it was concluded that the catalytic filter was promisingly useful for the industrial NOx reduction catalyst in order to treat the particulate and NO simultaneously.