• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.3
• /
• pp.93-100
• /
• 2014

This study presents the recomposition of MBM (measurement-based model) using natural frequencies and modes from the usually measured data, and the evaluation of cable tension in service from the analysis results upon MBM of existing CSB (cable stayed bridge). The cable tension is shown to be different according to the position attached to cable and loading type. The measured cable tensions are not different distinctly according to position attached cable under dead and live loads, but larger than those under design loads. The distribution of cable tension calculated upon the MBM is similar to those of measured tension although the former is more than those of cable tension upon the design model. Considering to long-term behaviors of cable, therefore, the design of cable in CSB needs to apply the analysis results on MBM. For this purpose, future study needs lots of measured data and MBM is used to analyze the long-term behavior of cable in CSB.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.5
• /
• pp.837-846
• /
• 1989

Belt tension distribution for an abrasive blet grinding was investigated analytically and experimentally for (1) slack side and (2) tight side blet grinding. Classical Eytelwein equation was used to predict the belt tension distribution with dividing contact angles into (1) inactive and (2) active angles. General friction theory was modified based on the friction force between the belt and the support in the grinding contact area that was obtained by experiments. It was found that analytical results were in good agreement with the experimental results. Also, the tight side belt grinding was recommended since it could carry out more grinding load than that of slack side belt grinding.

• Journal of the Korean Chemical Society
• /
• v.16 no.6
• /
• pp.341-348
• /
• 1972

The significance of the curvature dependency correction of surface tension is studied in calculating the pore volume distribution of porous adsorbent from nitrogen adsorption isotherm. That is, Kelvin radii are calculated with curvature dependent surface tension values calculated by Chang et al, and then with these Kelvin radii, pore volume distributions of three porous adsorbents, silica alumina (steam deactivated), silica gel (Davidson 59), and silica gel (Mallinc-krodt Standard Luminescent), are calculated. The results are compared with those obtained by the previous method in which surface tension is taken as constant and also with the others. obtained by the modelless method proposed by Brunauer et al. The maximum point of the distribution curve shift to the larger pore radius, when the curvature dependency is considered. Furthermore, the relative pressure at which capillary condensation commences is by far the lower than that accepted previously. This effect becomes significant as the pore radius approaches to the micropore range.

• Korean Journal of Soil Science and Fertilizer
• /
• v.28 no.2
• /
• pp.165-175
• /
• 1995

To determine the effect of soil moisture stress on growth of barley and grain quality, a pot experiment was carried out for two barley varieties(Olbori and Chogangbori) by using large plastic pot(52cm in diameter and 55cm in depth) filled with sandy loam soil under rain-controlled open green house. By means of measuring soil water potential with micro tensiometer and gypsum block installed at 10cm in soil depth, soil moisture was controlled by sub-irrigation at several irigation points such as -0.05bar, -0.2bar, -0.5bar, -1.0bar, -5.0bar and -10.0bar in soil water potential. The lower soil water potential was controlled, the shorter length of stem and internode became, and the more narrow stem diameter was. Leaf area was significantly decreased when soil water potential was controlled lower than -0.5bar, although chlorophyll content of flag and first leaves was not changed so much. Weight of grain and ear was significantly decreased when soil water potential was lower than -5.0bar and the highest grain yield was obtaind in a plot where soil water potential was controlled at -0.2bar. However, the most efficient water use of Olbori and Chogangbori was obtained at -0.5bar and -1.0bar in water potentials, respectively. Crude protain content, maximum viscosity, consistency and ${\beta}$-glucan content of barley flour increased as soil water potential significantly decreased, especially below -5.0bar, but gelatination temperature decreased as soil water potential decreased.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.3
• /
• pp.129-138
• /
• 2005

This paper presents a methodology for the determination of optimal managing criteria for cable tension force in cable-stayed bridges using acceleration data acquired by monitoring system. There are many long span bridges installed with monitoring system in Korea. The monitoring systems are installed to diagnose abnormal behavior or damages in bridges and to warn these to bridge management agency. In cable-stayed bridges, the cable tension force could be an important indicator of abnormal behavior because of the geometric configuration of the cable-stayed bridge. If the management value of cable tension force is set too high or too low, then the monitoring system could not warn properly for the abnormal behavior of a bridge. Generally, the management value is set by empirical or engineering judgment, but in this paper, a new methodology for the determination of managing criteria for cable tension force is proposed based on the probability distribution model for tension force and reliability analysis. The proposed methodology is applied to a real concrete cable-stayed bridge in order to investigate its applicability.

• Journal of Korean Society of Steel Construction
• /
• v.9 no.4 s.33
• /
• pp.579-588
• /
• 1997

During the construction of cable stayed bridge, errors are always caused by various reasons, accumulated and amplified through the complex construction steps. It is likely that the undesirable stress distribution of members and the large deflection of the bridge different from design values come out The adjustment of cables during construction is absolutely indispensable to correct the stress distribution of the members and the geometrical configuration of the bridge. In the conventional method, weight coefficients are used to consider the difference of units between cable forces and girder deflections during the optimization process of cable adjustment. However, it is not easy to determine weight coefficients and the adjustment must be repeated several times with the time consuming process of the determination of new weight coefficients in case that errors are out of design allowable limits. In this paper, fuzzy linear regression analysis is applied to the cable adjustment to overcome those problems. In the application of fuzzy linear regression analysis method the designer's intention and the design allowable limits can be formulated in the form of the constraints of the linear optimization problem. Therefore, the cable adjustment in construction site can be carried out with the fuzzy linear regression analysis more rapidly than with the convetional method.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.2
• /
• pp.125-131
• /
• 2014

Winding is an integral operation in almost every roll-to-roll continuous process and center-winding is suitable and general scheme in the winding system. However, the internal stresses within center-wound rolls can cause damage such as buckling, spoking, cinching, etc. It is therefore necessary to analyze the relationship between taper tension in winding section and internal stress distribution within center-wound roll to prevent the winding failure. In this study, an optimal taper tension control method with parabolic taper tension profile for producing high quality wound roll was developed. The new logic was designed from analyzing the winding mechanism by using the stress model in center-wound rolls. The performance of the proposed taper tension profile was verified experimentally.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.17-22
• /
• 2009

계절에 따른 토양공극의 수리학적 변화를 파악하기 위해서 설마천 유역의 범륜사 독립사면과 광릉 원두부 소유역의 독립사면을 대상으로 장력침투실험을 실시하였다. 토양수분 확보에 신뢰를 받기위해서 TDR(Time Domain Reflectometry)및 현장에서 토양의 불포화 투수계수 측정이 가능한 장력침투계(Tension infiltrometer)를 이용하였다. 계절에 따른 자료수집을 위해서 2008년 3월 20일 부터 약 6주간격으로 10월 29일까지 5회에서 6회 토양수분 자료 및 토양장력침투 자료를 획득하였다. 획득한 자료를 이용하여 포화 및 불포화 수리전도도, 대공극 유효흐름분율(macropore flow), 대공극 유효부피분율을(effective macroporosity) 나타내었다. 분기별로 자료분석 결과 계절별 특성이 나타남을 알 수 있다. 수리전도도는 3월, 5월, 10월은 유사한 반면 6월과 7월 그리고 9월은 상대적으로 높았다. 이는 여름철에 공극 발달이 활발하다는 것을 의미한다. 선행토양수분은 수리전도도에 영향을 미치는 것으로 나타났다. 대공극의 발달은 삼림과 같은 복잡 경관에서는 강우사상에 따른 토양수분의 공간 분포 및 이송, 유출과정이 물순환에 영향을 미친다. 지형분석을 통한 공극의 흐름특성과 토양수분 유의성에 대하여 논의하였고, 대공극 변화에 밀접한 관계가 있는 식생과 그밖에 계절적으로 발달을 일으키는 요인을 모색 하였다. 본 연구는 계절에 따라 변하는 수리전도도를 기초로 하여 불포화대에서 토양공극의 수리학적 변화와 시공간적으로 침투흐름에 얼마나 영향을 주는가를 보여준다.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2006.05a
• /
• pp.340-341
• /
• 2006

입자분포가 서로 다른 분체를 소수화 및 친수화 표면을 갖도록 표면개질을 하여 solid casting으로 성형하여 소결함으로써 계면장력에 의한 전기적 반발로 자기배열 구조를 갖는 다층 다공질 구조의 세라믹 담체의 제조가 가능하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.13 no.2 s.54
• /
• pp.129-136
• /
• 2009

The paper presents an algorithm of selecting optimal locations for measuring displacements(OLD) to adjust cable tension forces during the construction of cable-stayed bridges. The rank for optimal locations can be determined from the effective independence distribution vectors(EIDV) that are computed from the Fisher Information Matrices(FIM) formulated with the displacement sensitivities. To examine the efficiency and reliability of the proposed algorithm for determining OLD, a simulation study on a cable-stayed bridge has been carried out. The results using FIM formulated with displacements are compared with those using FIM with displacement sensitivities through the simulation study. The effects of measurement noise and error in cable length on the adjustment of cable tension forces are evaluated statistically by applying the Monte Carlo scheme.