• Composites Research
• /
• v.21 no.1
• /
• pp.40-45
• /
• 2008

Rubber hose assembly for automotive hydraulic brake during operation is subject to combined stresses of cyclic pressure, cyclic bending and torsion as well as thermal load. The rubber hose is composed of ethylene-propylene diene monomer(EPDM) rubber layers reinforced by polyvinyl acetate(PVA) braided fabrics. A durability tester with loading rigs for inducing the above cyclic stresses was used to investigate failure mechanisms in the rubber hose assembly. Failure examination was performed at every 100 thousands cycles of bending and torsion. Hose samples were sectioned with a diamond-wheel cutter and then polished. The polished surface was observed by optical microscope and scanning electron microscope (SEM). Some interfacial delamination with a length of about 1mm along the interface between EPDM rubber and PVA fabrics was shown at the test cycles of 400,000. The delamination induced some cracking into the outer rubber skin layer to leading the final rupture of the hose.

• Tribology and Lubricants
• /
• v.27 no.5
• /
• pp.269-274
• /
• 2011

The purpose of this paper is to study and analyze the improvement method for the failure examples including the vehicle brake system in actual field. It was verified that the indicator plate of pad wear scratched the brake disk because of wearing after displacement of non- identification parts pad. The caliper of other vehicle was installed with brake system verified the phenomenon produced groove in center point because of one side wear when the pad was not fully contacted with the rub disk by other action surface pressure and pad action condition. It verified that the crack phenomenon fatigue was produced by brake thermal deformation because of decreasing the thickness by grinding to modify the non-uniformed wear of brake disk. It verified that the friction sound was produced by the friction phenomenon because of non-uniformed contact of lining and an alien substance with inner of the drum and lining braking by crack phenomenon with brake drum surface.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.4
• /
• pp.440-445
• /
• 2011

This paper presents a new regenerative brake system of electric vehicles that employs a continuous variable transmission(CVT) and a flywheel. The developed device has advantages over existing regenerative brakes from a standpoint of reliability and versatility in actual driving conditions. The system consists of a CVT, two wheels, a flywheel, a coupling and auxiliary powertrain components. The CVT is designed as a combination of two cones and a roller, which causes the velocity difference between the wheel and the flywheel. The power flow of the flywheel system is controlled by the CVT roller and the coupling through step motors. A prototype has been developed and then its performance has been investigated for various operating conditions. Results show that the storage efficiency of the flywheel is much affected by the vehicle's velocity and it is reduced below 20% for high speed, as compared to the 25% efficiency for an ideal condition. The CVT is a primary factor for lowering the flywheel efficiencies due to large friction and slipping between the cone and the roller.

• Transactions of Materials Processing
• /
• v.27 no.3
• /
• pp.165-170
• /
• 2018

In order to increase the lifetimes of cold forging dies, insert rings are generally used. In this study, an insert ring and shrunk ring of the flange upsetting die were designed for the cold forging of an automotive wheel nut. The Stress distribution occurring in the die during forging was simulated using a commercial finite element analyzing program. The effects of the fitting interference and inclined angle of the insert ring on the compressive stress of the die inside were also investigated. The simulated data were compared with the real lifetimes of the forging dies. The maximum compressive stress acting on the edge of a forging die should have the most influence on die lifetime, an idea which could help develop the die design with the longest lifetime. The design of the most optimal forging die with the longest lifetime is made possible by analyzing the maximum inner pressure and principal stress between the shrunk ring and insert ring.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.5
• /
• pp.105-112
• /
• 2017

In this study, plastics were deformed after molding due to the characteristics of the material. The Taguchi experimental design method was utilized to find the molding conditions that minimized deformation of the plastic bezel to be assembled in an automotive steering wheel. The injection molding conditions applied to the experimental design method are the melt temperature, cavity plate coolant temperature, core plate coolant temperature, and cooling time. Each condition was divided into five levels, and a total of 25 experiments were planned. However, instead of performing 25 actual molding experiments, the injection molding analysis was performed using the Moldflow program, and the deformation values for each molding analysis were obtained. The optimal molding conditions were obtained from these deformation values. The actual injection molding experiment using optimal molding conditions was compared with the deformation amount of the current molded product. The deformation was measured using a precise 3D scanner. The deformation amount of the molded product under optimal molding conditions was 16.1% lower than the deformation amount of the current molded product.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.5
• /
• pp.229-234
• /
• 2017

In this study, TiAl alloy was fabricated by a centrifugal casting method for turbo charge of automotive. Optimum conditions for defectless morphology using various ceramic mold were investigated. The crystal structure, microstructure, and chemical composition of the TiAl prepared by centrifugal casting were studied by X-ray diffractometer (XRD), optical microscopy (OM), field emission scanning electron microscopy (FE-SEM) and energy dispersive spectroscopy (EDS), microvickers hardness analyzer (HV). Two kinds of dendrite structures were observed with 4-fold and 6-fold symmetries. The FE-SEM, EDS and HV examinations of the as-cast TiAl showed that the thickness of the oxide layer (${\alpha}$-case) was typically less than $50{\mu}m$.

• Journal of KSNVE
• /
• v.9 no.3
• /
• pp.613-620
• /
• 1999

Brake judder{or cold judder) caused by the disc thickness variation(DTV) is investigated experimentally, This cold judder is often perceived by steering wheel vibration, brake pedal pulsation, and vehicle body vibration. In this paper, how the DTV profile affects the vibration characteristics of vehicle body is shown by order tracking analysis(OTA) and operational vibration analysis(OVA) The tri-axial vibrations are measured at the knuckle, lower rm, and the body side of the lower arm. Also, measured are the wheel speed and the detail DTV profile. The interpretations of OTA results in three directions of tested vehicle indicate the relative importance in the contribution of the run-out and the DTV to the judder vibration. Also, the OVA results show the prominent vibration amplitude of the lower arm in the direction of the vehicle movement. in which the second order of wheel speed is dominant. These results could be used to diagnose the judder problem and to establish the correction methods.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.140-140
• /
• 2017

4륜 장착 자동차의 토크 전달은 2륜 구동, 4륜 구동 모드를 간단히 전환하는 방식(part time 4WD)과 항시 사륜 구동 모드에서 전후륜의 토크 전달비를 제어하는 방식(AWD, all wheel drive)이 있다. 경제의 발달에 따라서 취미 인구의 확대로 국내에만 180만 명의 R/C car 사용자가 있다. 이 중 2WD-4WD의 전환을 differential lock mechanism으로 구현한 수입산 모델의 가격이 1,000,000원을 호가하지만 가변 제어 방식이 아닌, 정차 후 2-4륜 구동 전환 방식을 적용하고 있으며 상대적으로 내구성이 떨어진다. DC motor의 출력이 늘어나고 배터리의 성능이 좋아진 현재 소형 RC car의 최고 속도는 80 km/h 정도로 빨라졌다. 그러나 마찰 계수가 낮은 노면(실내의 대부분 평활 처리된 복도)에서는 2륜 구동 모드의 활용도가 매우 낮다. 미끄러운 노면에서 후륜 구동 모드로는 oversteer가 발생하여 차량이 스핀하기 쉽고 전륜 구동 모드로는 understeer가 발생하여 제대로 된 코너링이 어렵다. 상시 4륜 구동 모드는 에너지 소모가 크고 전후륜이 tight coupling되어 있는 문제 때문에 일반적인 노면에서 부드러운 코너링이 잘 이루어지지 않는 문제가 있다. 본 연구에서 제안하는 방식은 그림 1와 같이 center shaft의 중간에 영구 자석으로 만들어진 토크 전달용 판이 있고 그 사이에 자계를 차폐할 수 있는 강자성체 셔터를 서보 기구에 연결하여 서보 회전각에 따라서 구동 쪽의 토크가 피구동축으로 전달되는 양을 연속 가변제어할 수 있다. 토크 전달용 판의 차폐 면적에 따른 토크 전달양을 전/후륜 바퀴의 Static torque를 통해 측정하였으며(그림 2), 공중 상태에서 즉 공기저항만을 고려한 상태에서의 RPM 회전수 차이 측정(그림3)을 통해 구동 쪽의 회전수가 피구동축으로 전달되는 양을 측정하여 연속가변 토크 제어 전달 기구의 성능을 확인하였다. 이 기구는 현재 1차적으로는 remote controller의 ch 3(ON/OFF제어 방식)에 연결하여 특정한 양의 토크를 전륜 쪽으로 보낼 수 있도록 구현이 가능하며, ch 2(PID제어 방식)에 연결하여 연속 가변 조절이 가능하도록 구현이 가능하다. 부가적으로 Arduino board를 내장하여 전후륜의 휠센서에서 입력되는 신호를 감지하여 자동적으로 전후륜에 배분되는 토크를 제어할 수 있도록 설계 중에 있다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.2
• /
• pp.172-178
• /
• 2015

The control moment gyroscope(CMG) which is well known as an effective high-torque-generating device is applicable to space vehicles, airplanes, ships, automobiles, robotics, etc. for attitude stabilization and maneuver. This paper deals with the overall details of 100Nm-class CMG development for various industrial applications, and provides the activities and results associated with the CMG system-level requirement analysis, the motor subsystem design/manufacturing/integration, the construction of ground support equipment, and the performance test and evaluation. The performance test reveals that the CMG generates the torque output more than 120Nm in as-designed operation of spin motor and gimbal motor.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.216-218
• /
• 2014

자동차용 고광택 크롬 도금 박리액에는 질산과 유가금속인 구리 및 니켈이 다량 함유되어 있는 것으로 알려져 있다. 질산($HNO_3$) 및 유가금속은 고가이며 유독하므로 경제적 및 친환경적으로 반드시 회수하여 재활용하여야 한다. 본 연구에서는 도금박리액으로부터 질산과 구리, 니켈을 용매 추출법을 이용하여 분리하였다. 수상에 존재하는 질산의 농도는 0.01 ~ 1N NaOH를 이용하여 적정하여 분석하고, 금속의 농도는 ICP-MS 및 ICP-AES 등을 이용하여 분석하였다. 도금 박리액을 분석한 결과 Cu(76850mg/L), Ni(51990 mg/L)이 함유되어 있음을 알 수 있었다. 용액 내 질산의 양을 NaOH 용액을 이용하여 적정법으로 측정하였을 때, 질산의 양은 대략 1.02 M 임을 알 수 있었다. 50 % Tributylphosphate (TBP)를 이용하여 3단 추출한 유기층의 용액을 증류수를 이용하여 3회의 역추출을 하였을 때, 원액으로부터 48.1 %의 질산을 회수할 수 있음을 알 수 있었으며, 순도는 99.5% 이상이었다. 질산 회수 후 용액 내에 남은 구리와 니켈은 ISE-106로 구리를 추출하여 니켈을 분리한 후 황산을 이용해 역추출 하였다. 회수된 구리는 NaOH를 이용하여 pH를 조절하고 수산화구리 형태로 침전시킨 후 $N_2H_4$를 이용하여 환원시켰고, 온도와 pH 및 환원제를 이용하여 다양한 조건 하에 구리 분말을 제조하였다. 구리를 추출하여 라피네이트 용액으로 분리된 니켈은 $NaBH_4$를 이용하여 환원시켰고, 다양한 조건 하에서 니켈 분말을 제조하였다. 환원 된 분말은 분석결과 99%의 순수한 분말임을 알 수 있었다.