• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.4
• /
• pp.7-15
• /
• 2008

In manufacturing aircraft, safety and lightness of structure are important factors. Utilizing autofrettage technique, these benefits can be obtained. This technique is most frequently applied to a single cylinder. However, the Bauschinger effect reduces the benefits of autofrettage process Therefore, there is increasing interest in the use of compound cylinder that combine shrink fit and autofrettage. In this paper, single and compound cylinders that has same geometry were considered. It was found that compound cylinder which was autofrettaged has lower tangential hoop stress and plastic strain than single cylinder at bore. This means a reduction in the impact of the Bauschinger effect after shrink-fitting which produces the beneficial bore hoop stress.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.9
• /
• pp.845-851
• /
• 2017

Fatigue failure of an autofrettaged pressure vessel with a groove at the outside surface occurs owing to the fatigue crack initiation and propagation at the groove root. In order to predict the fatigue life of the autofrettaged pressure vessel, residual stresses in the autofrettaged pressure vessel were evaluated using the finite element method, and the fatigue properties of the pressure vessel steel were obtained from the fatigue tests. Fatigue life of a pressure vessel obtained through summation of the crack initiation and propagation lives was calculated to be 2,598 cycles for an 80% autofrettaged pressure vessel subjected to a pulsating internal pressure of 424 MPa.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.4
• /
• pp.39-45
• /
• 2010

Thick-walled cylinders, such as a cannon or nuclear reactor, are autofrettaged to induce advantageous residual stresses into pressure vessels and to increase operating pressure and the fatigue lifetimes. As the autofrettage level increases, the magnitude of compressive residual stress at the bore also increases. The purpose of the present paper is to predict the accurate residual stress of SCM440 high strength steel using the Kendall model which was adopted by ASME Code. Hydraulic pressure process was applied in the inner part and thick-walled cylinders were autofrettaged up to 30% overstrain levels. Electro polishing on the surface of autofrettage specimen was performed to get more accurate residual stress. Residual stresses were measured by X-ray diffraction method. The autofrettage surface which was plastically deformed analyzed using a scanning electron microscope(SEM). Although there were some differences in measured residual stress and numerical results, it has a tendency to agree comparatively with each other.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.620-625
• /
• 2007

Autofrettage process is used for internal forming and sizing of cylinder designed to withstand high internal pressures. Once the tube is autofrettaged, it needs to be machined to its final dimensions both at the bore and its outer surface. This paper presents an analytical analysis and numerical analysis of machined compound cylinder using finite element code, ANSYS10.0. An analytical model for predicting the level of autofrettage following either inner, outer, or combined machining of the compound cylinder is developed for the autofrettage residual stress field is simulated by an autofrettaged pressure. The autofrettaged pressures are obtained by using trying-error method. As autofrettage percentage is 20 %, the numerical results are found to be in almost agreement with the analytical ones. However, as autofrettage percentage is 60 %, the numerical results have a little difference with the analytical ones.

• Journal of the KSME
• /
• v.31 no.4
• /
• pp.356-363
• /
• 1991

선형 탄성 유한요소 응력해석과 평균응력 효과를 고려한 저주기 피로실험으로부터 결정된 피로 특성, 그리고 국부변형률 방법을 종합하여 외경에 흠이 존재하는 자긴가공된 두꺼운 압력 용기의 피로수명이 평가되었다. 직사각형의 매우 날카로운 흠에서의 응력집중계수는 타원형 홈에서의 응력집중계수의 약 두배의 값이 얻어졌으며, 고강도 압력용기강인 ASTM A723의 저주기 피 로거동에 대한 평균응력 영향은 Morrow 및 SWT 파라메타를 이용하여 충분히 고려되었다. 균열발생이 예상되는 위험한 부분인 홈의 뿌리부분에서의 국부적인 응력, 변형률이 계산되었으며 예측된 피로수명은 실험적으로 얻어진 수명과 비교했을 때 2에서 4배의 오차를 보이면서 일치 하는 결과를 얻었다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.7 s.262
• /
• pp.800-807
• /
• 2007

Autofrettage process is used for internal forming and sizing of cylinder designed to withstand high internal pressures. Once the tube is autofrettaged, it needs to be machined to its final dimensions both at the bore and its outer surface. This paper presents an analytical analysis and numerical analysis of machined compound cylinder using finite element code, ANSYS10.0. An analytical model for predicting the level of autofrettage following either inner, outer, or combined machining of the compound cylinder is developed for the autofrettage residual stress field is simulated by an autofrettaged pressure. The autofrettaged pressures are obtained by using trying-error method. As autofrettage percentage is 20 % and 40 %, the numerical results are found to be in almost agreement with the analytical ones. However, as autofrettage percentage is 60 %, the numerical results have a little difference with the analytical ones.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.90-95
• /
• 2007

In order to investigate the optimum condition of the autofrettage process for the diesel engine injection pipe, different values of autofrettage pressure, pressure rising time, pressure holding time, and repetition of autofrettage process were applied. Autofrettage was preformed by applying the hydrostatic internal pressures of 603 MPa, 535 MPa, 500 MPa on the fuel injection pipe, corresponding to theoretically 50%, 30%, and 20% overstrain levels, respectively. The autofrettage residual stresses in the injection pipe were experimentally determined by using X-ray diffractometer. As the overstrain level increased, the magnitude of compressive residual stress at the bore increased. It was found that the rising time to reach the autofrettage pressure, holding time at the autofrettage pressure, and repeating application of the autofrettage pressure on the pipe had no significant influence on the residual stress distributions.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.637-642
• /
• 2008

Autofrettage analysis of a bend in the fuel injcetion pipe has been performed to investigate the distribution of residual stresses due to pipe bending and autofrettage processes. The pipe bending was simulated by metal forming analysis using finite element method, and residual stress distribution after bending was found. Autofrettage following the pipe bending was performed by applying the hydrostatic internal pressures of 603 MPa, 535 MPa, 500 MPa on the pipe bend, corresponding to theoretical 26 %, 14 %, 9 % overstrain levels, respectively. Residual stress distributions due to bending and autofrettage were evaluated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.2
• /
• pp.321-329
• /
• 1998

To ensure the structural integrity of the autofrettaged thick-walled cylinder subjected to cyclic internal pressure loading, the fatigue crack propagation life of the cylinder was evaluated. Stress intensity factors of the external cracked cylinder due to internal pressure and autofrettage loadings were calculated using the finite element method. The fatigue crack propagation lives of the cylinder based on the fracture mechanics concepts were predicted and compared to the experimental fatigue lives evaluated from the C-shaped simulation specimens. There were good correlations between the predicted and experimental fatigue lives within a factor of 3 for the single and double grooved C-shaped simulation specimens. Predicted fatigue crack propagation lives of the double grooved cylinders were about 1.5-5 times longer than those of the single grooved cylinders depending on the levels of autofrettage.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.311-316
• /
• 2008

Thick-walled cylinders, such as a cannon or nuclear reactor, are autofrettaged to induce advantageous residual stresses into pressure vessels and to increase operating pressure and the fatigue lifetimes. As the autofrettage level increases, the magnitude of compressive residual stress at the bore also increases. The purpose of the present paper is to predict the accurate residual stress of SCM440 high strength steel using the Kendall model which was adopted by ASME Code. Hydraulic pressure process was applied and thick-walled cylinders were autofrettaged up to 30% overstrain levels. Electro polishing was performed to get more accurate data. Residual stresses were measured by X-ray diffraction method. The autofrettaged surface which was plastically deformed analyzed using a scanning electron microscope(SEM). Although there were some differences in measured residual stress and numerical, there is a tendency to agree.