• Journal of Sensor Science and Technology
• /
• v.11 no.6
• /
• pp.327-334
• /
• 2002

Fine particles of $SnO_2$ were fabricated by the sol-gel powder processing using tine(II) chloride dihydrate($SnCl_2{\cdot}2H_2O$) and ethanol($C_2H_5OH$) as raw materials. The powders were investigated about the properties and electrical sensing. Gel powders were fabricated by drying of sol at $120^{\circ}C$ after aging 72hrs and 168hrs. The amount of $SnO_2$ phase was increased below $600^{\circ}C$ due to the elimination of volatile components, and the $SnO_2$ phase was almost completed by the heat treatment at $700^{\circ}C$ for 30min. The grain sizes were about 30nm below $700^{\circ}C$, and it showed the narrow distribution of the grain sizes. The specimens to measure electrical properties were fabricated by the thick film screen printing technique on the alumina substrates. The conductance of $SnO_2$ was showed the intrinsic behaviour of semiconducting ceramics above at $450^{\circ}C$. The constant conductance was observed in the temperature range of $200{\sim}450^{\circ}C$. The sensing properties of response time, recovery, and sensitivity of CO were improved with aging time.

• Journal of Sericultural and Entomological Science
• /
• v.33 no.1
• /
• pp.13-20
• /
• 1991

The flacheric virus(FV) was isolated from the diseased larvae with flaccidity symptoms of the silkworm, Bombyx mori, which were collected in Hyangnam, Kyunggi Province and in Youcheon, Kyungpook Province. The properties of the virus were investigated and compared with the Japanese FV in morphology, size, nucleic acid and structural proteins. The Hyangnam isolate had a diameter of 27$\pm$1, 7nm with speherical shape and contained RNA of which the electrophoretic pattern was same as that of the Japanese FV. The virus had four sturctural proteins and their molecular weight were estimated as 35, 000, 33, 000, 31, 000, and 11, 400 daltons, respectively. The Youcheon isolate had two different sizeds in diameter of 27$\pm$1.7nm and 21$\pm$0.8nm. The antigenicity of the Hyangnam isolate was proved to be identical to that of Japanese FV, whereas the antisera against the Youcheon isolate (mixed with two different sizes) reacted with Japanese FV and densonucleosis virus type 1, respectively. From these characteristic of the isolated viruses, it was concluded that the Hyangnam isolate was identical to the Japanese FV and the Youncheon isolate contained the same viruses as the Japanese FV and DNVI.

• Applied Microscopy
• /
• v.35 no.1
• /
• pp.23-30
• /
• 2005

Many studies have been performed on the bovine leukemia virus (BLV) since bovine leukosis had been reported in 1968 in Korea. However, there was no report on the ultrastructural examination of BLV. An attempt to detect C-type viral particles in the cultured peripheral blood lymphocytes of Holstein-Friesian dairy cattle, was made to determine whether in vitro viral expression might be used as a reliable method to identify the cow which is likely to transmit BLV. In transmission electron microscopic (TEM) examination, the virus particles were found predominantly outside of the lymphocytes even though a few particles were also observed within the membrane bound cytoplasmic vacuoles. All of them were C-type particles consisting of a central, electron-dense core separated by a clear area from a limiting envelope with a unit membrane structure. Virus particles were easily detected in the lymphocyte which was cultured with medium supplemented with either T-lymphocyte mitogen (conconavalin A) or B-lymphocyte mitogen (lipopolysaccharide). Identical viral particles, although fewer, were also consistently present in the lymphocytes cultured with medium which was containing foetal bovine serum (FBS) only and which was containing neither FBS or mitogen. By contrast, no virus particle was detected in extensive examination of lymphocytes before culture. In conclusion, the BLV cultivation and detection methods established in this study could be used as a tool to identify and eliminate the cattle which can transmit the BLV.

• Journal of the Korean earth science society
• /
• v.33 no.3
• /
• pp.280-293
• /
• 2012

In order to clarify the characteristics of dispersion of volcanic tephra emitted from the Mt. Baegdu with various eruption environment, numerical analysis were performed using numerical models, Weather Research and Forecast (WRF) and FLEXPART. Synoptic conditions at 12 October 2010 was adopted because the volcanic ash of Mt. Baegdu can reach the Korean peninsula and its dispersion pattern was compared with different Volcanic Explosivity Index (VEI) and particle size. Predominant size of falling out ash flowing in the peninsular is smaller than 0.5 mm and the ash large than the size is difficult to get in the peninsular due to the its weak ability of truculent diffusion. the difference of ash distribution with various VEI scenarios is not so much but number density of ash in the air is dramatically changed. Volcanic ash tends to be deposited easily in eastern coastal area such as Gangneung and Busan, because of the inflow of ash from East Sea and barrier effect of the Taeback mountains along the east coast of the Korean Peninsula. Accumulated amount of ash deposition can be increased in short period in several urban areas.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.39 no.4
• /
• pp.542-547
• /
• 2010

Physico-chemical properties of starches from potato cultivars with different colors were investigated. White Atlantic potato had 10% higher starch yield than violet Bora Valley potato. It turned out that the shape and structure of Atlantic and Bora Valley potato starch were the same by mechanical analysis using X-ray and SEM. The ratio of $50\;{\mu}m$ particle in starches from Atlantic and Bora Valley potato was $45.44\pm2.79%$ and $42.37\pm1.03%$ respectively. The particle size of Atlantic potato starch was less than that of Bora Valley; however, there was no significant difference (p<0.05). As for moisture coupling, there was no difference (p<0.05) between the two potatoes. Swelling power showed a high increase from $65^{\circ}C$ to $80^{\circ}C$. The swelling power of Atlantic starch was higher by about 0.3% than that of Bora Valley at $90^{\circ}C$. Since Atlantic has smaller starch particles than Bora Valley, more starch particles are contained in the same size, and hence a difference in swelling power. As a result of measuring the gelatinization of potato starches from Atlantic and Bora Valley, a higher gelatinization start, climax, and complete temperatures occurred at Bora Valley than Atlantic. As for gelatinization enthalpy, Bora Valley starch with a higher gelatinization temperature consumed more energy for gelatinization.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.2
• /
• pp.247-253
• /
• 1996

Microscopic analysis has been performed in order to investigate effects of the microstructure of the starting feed rods on the morphology of the S-L interface and the stability of the molten zone during single crystal growth of $SrTiO_{3}$ using a floating zone method. Undoped and $Fe_{2}O_{3}$ doped $SrTiO_{3}$ doped $SrTiO_{3}$ specimens, sintered at the different temperatures have been used. In the case of the feed rods sintered at the lower temperature($1400^{\circ}C$), the poor densification made the stability of the molten zone difficult to maintain. The feed rods sintered at the higher temperature ($1600^{\circ}C$) exhibited the higher density but their molten zone was difficult to maintain due to the presence of the abnormally grown grains. It is concluded that the uniform grain size distribution of the feed rod is the critical factor to maintain the stable molten zone and therefore to give optimum growth condition during FZ single crystal growth.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.4
• /
• pp.589-598
• /
• 2000

A pilot-scale Spray Drying Sorber (SDS) system was set up to evaluate the effect of spray characteristics on the desulfurization yield. The size distribution and the Sauter Mean Diameters of slurry droplets were measured in advance using the optical size measurement system, Malvern 2600. The desulfurization yield of the drying chamber by size was measured for the conditions of inlet gas and spray injection. As a reagent, 10% limestone slurry of $Ca(OH)_2$ was treated with flue gas containing $SO_2$, and the combustion gas analyzer and gas detectors were attached to measure the $SO_2$ concentration. With a flow rate of 144 Nm3/h and a temperature range of $200{\sim}300^{\circ}C$, the experiments were performed for the Stoichiometric Ratio (SR) of 1.0 to 3.0 and droplet mean diameter of 6.5 to $34.3{\mu}m$. In case of smaller spray droplets, the desulfurization efficiency improved due to the increase of total droplet surface area, while the reduction in evaporation time reduced the contact time between the droplets and $SO_2$ gas. In some typical region of droplet diameter, this negative effect, reduction of contact time, became dominant and the desulfurization yield decreases the desulfurization yield in spite of the expansion in absorption area. These results revealed that there exists the optimal size of spray droplets for a given state, which is determined by the compromise between the total surface area of slurry droplets and the evaporation time of droplets. The measurements also indicated that the inlet temperature of flue gas changes the optimal injection condition by varying the driving force for evaporation. The results confirm that the effect of the evaporation time of slurry droplets should be considered in analyzing the desulfurization yield as well as the total surface area, for it is a significant aspect of the correlation with the capabilities of $SO_2$ absorption in wet droplets. In conclusion, the optimal condition of spray can be determined based on these results, which might be applied to design or scale-up of SDS system.

• Proceedings of the Korean Society of Applied Pharmacology
• /
• 1992.05a
• /
• pp.64-64
• /
• 1992

1. Eudragit RS, RL, E, S 및 L을 이용하여 유중건조법으로 제조한 $\beta$-락탐계 항생제 (Amoxicillin, Cephalexin) 마이크로캅셀 모두가 구상 성형성과 정립성이 양호한 결과를 얻었다. 2. 분리 분산제 (aluminium tristearate)의 양을 고정시켰을 때에는 일정한 입자 분포도를 가지는 마이크로캅셀을 얻을 수 있었고, 양을 증가시켰을 때에는 입자 크기는 작아 졌으며, 용출율은 증가하였다. 3. Eudragit RS 및 S 마이크로캅셀제제로부터의 약물용출은 저조하였고, Eudragit RL 및 L 제제로부터의 약물용출은 양호하였다. 따라서 Eudragit RS/RL 마이크로캅셀제제에서는 Eudragit RL의 양을 증가시킬수록 약물의 용출율이 증가하였으며, Eudragit S/L 마이크로캅셀제제에서는 Eudragit L의 양을 증가시킬수록 약물의 용출율이 증가하였다. 약물방출 실험결과, Amoxicillin 함유Eudragit RS/RL (25/75) 마이크로캅셀, cephalxin함유 Eudragit RS/RL (75/25) 마이크로캅셀 및 Eudragit S/L (75/25) 마이크로캅셀제제는 유용한 제제로 펑가되었다. 또한 수용성 고분자인 polyethylene glycol을 혼합하어 제조하는 것에 의해 방출조절성 마이크로캅셀의 제조가 가능하였다. 유중건조법을 이용하여 본 연구방법으로 저조한 마이크로캅셀제제는 투어횟수를 줄일 수 있을 뿐만 아니라 생체에 대해 안전하고 재현성에 확보되는 유용한 제제로 판단된다. 앞으로 연구를 계속 수행하여, 특히 약물의 물리화학적 성질 및 생제내 투어 후의 생물약제학적 펑가를 엄격히 하므로써 안정성이 심히 문제시되는 다용 약물계열에 대한 조절방출성제제의 개발을 기대할 수 있다.은 해리항수의 역수이므로 해리항수가 적을수록 $\beta$ 수용체에 대한 친화력이 큰 약물이다. 시사되었으며, 이 조직에서 또한 5-$HT_2$와 5-$HT_3$ 수용체의 존재를 확인하고 각각의 기능을 분명히 했다.가 수월하게 하였고 메모리를 동적으로 관리할 수 있게 하였다. 또한 기존의 smpl에 디버깅용 함수 및 설비(facility) 제어용 함수를 추가하여 시뮬레이션 프로그램 작성을 용이하게 하였다. 예를 들면 who_server(), who_queue(), pop_Q(), push_Q(), pop_server(), push_server(), we(), wf(), printfct() 같은 함수들이다. 또한 동시에 발생되는 사건들의 순서를 조종하기 위해, 동시에 발생할 수 있는 각각의 사건에 우선순위를 두어 이 우선 순위에 의하여 사건 리스트(event list)에서 자동적으로 사건들의 순서가 결정되도록 확장하였으며, 설비 제어방식에 있어서도 FIFO, LIFO, 우선 순위 방식등을 선택할 수 있도록 확장하였다. SIMPLE는 자료구조 및 프로그램이 공개되어 있으므로 프로그래머가 원하는 기능을 쉽게 추가할 수 있는 장점도 있다. 아울러 SMPLE에서 새로이 추가된 자료구조와 함수 및 설비제어 방식등을 활용하여 실제 중형급 시스템에 대한 시뮬레이션 구현과 시스템 분석의 예를 보인다._3$", chain segment, with the activation energy of carriers from the shallow trap with 0.4[eV], in he amorphous regions.의 증발산율은 우기의 기상자료를 이용하여 구한 결과 0.05 - 0.10 mm/hr 의 범위로서 이로 인한 강우손실량은 큰 의미가 없음

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.4
• /
• pp.589-609
• /
• 2017

This study carried out the density and energy dispersive X-ray spectroscopy and particle size analysis which are the physical characteristics of coal dust by collecting samples of coal dust in the five domestic mines to control the coal dust through ventilation in the workplace for coal mining in the country. This will contribute to a more comfortable working environment by understanding the physical characteristics of the coal dust which is derived from any hard coal produced domestically. In particular, the result of PSA analysis showed that the size of coal dust sample for this study ranged from $0.007{\sim}88.614{\mu}m$ were the particles less than $3.5{\mu}m$, the size range responsible for pneumoconiosis. To observe the flow of coal dust collected on the wind speed, the fallout of coal dust produced by the wind tunnel for the wind was measured and the particle size analysis of coal dust fallout was carried out. In addition, airborne dust is measured according to the mine velocity by using a multi-stage Anderson sampler in the mine where fine dust is generated in a large amount and the wind speed is found out to control the coal dust below $3.5{\mu}m$. In addition, natural ventilation pressure of A mine was calculated to prevent over design of the main fan.

• Polymer(Korea)
• /
• v.28 no.2
• /
• pp.135-142
• /
• 2004

Poly(vinyl acetate) (PVAc) prepared by emulsion polymerization has broad applications for additives such as paint binder, adhesive for wood and paper due to its low glass transition temperature which help to plasticize substrate resins. Since emulsion polymerization has a disadvantage that surfactant and ionic initiator degrade properties of the product polymer, poly(vinyl acetate-co-butyl acrylate) (VVc-BA) was synthesized using potassium persulfate as catalyst and poly(vinyl alcohol) (PVA) as protective colloid to prevent the degradation. The copolymer latex product was internally plasticized and has enhanced colloid stability, adhesion, tensile strength and elongation. During VAc-BA emulsion polymerization, no coagulation and complete conversion occur with the reactant mixture of 0.7wt% potassium persulfate, 15wt% poly(vinyl alcohol) (PVA-217), and the balanced monomer that the weight ratio of vinyl acetate to butyl acrylate is 19. As the concentrations of PVA increase, the copolymerization becomes faster and polymer particles are more stable, resulting in enhanced mechanical stability of the VAc-BA copolymer. However, the size of the polymer particles decreases with increasing PVA contents. Properties of the VAc-BA copolymer, such as minimum film formation temperature, glass transition temperature, surface morphology, molecular weight and molecular weight distribution, tensile strength and elongation, were characterized using differential scanning calorimeter, transmission electron microscope and other instruments.