• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.205-209
• /
• 1996

원자로 입구노즐에서 원자로 냉각재 펌프에 의한 맥동압력 준위를 원자로 하향통로와 저온 관을 상관시켜 예측하는 방법에 관하여 분석하였다. 원자로 하향통로에서의 맥동압력은 원자로 내부구조물의 건전성 평가에 쓰이는 중요한 인자로 이 값을 정확히 구하기 위해서는 경계조건인 입구노즐에서의 맥동압력을 정확히 예측해야 한다. 이를 위해 원자로 하향통로와 저온관을 상관시켜 원자로 입구노즐에서의 펌프에 의한 맥동압력 준위를 계산하였으며 Palo Verde Unit 1의 실험치와 비교 분석하였다. 분석 결과, 제시된 맥동압력 준위 예측모델은 500℉의 경우 비교적 잘 일치하였으나, 565℉의 경우 상당한 차이가 있었으므로 추가적인 검토 및 수정 작업이 요구된다.

• Journal of Energy Engineering
• /
• v.23 no.4
• /
• pp.95-105
• /
• 2014

The CUPID code has been developed for a transient, three-dimensional, two-phase flow analysis at a component scale. It has been validated against a wide range of two-phase flow experiments. Especially, to assess its applicability to single- and two-phase flow analyses in the Calandria vessel of a CANDU nuclear reactor, it was validated using the experimental data of the 1/4-scaled facility of a Calandria vessel at the STERN laboratory. In this study, a preliminary thermal-hydraulic analysis of the CANDU reactor moderator tank using the CUPID code is carried out, which is based on the results of the previous studies. The complicated internal structure of the Calandria vessel and the inlet nozzle was modeled in a simplified manner by using a porous media approach. One of the most important factors in the analysis was found to be the modeling of the tank inlet nozzle. A calculation with a simple inlet nozzle modeling resulted in thermal stratification by buoyance, leading to a boiling from the top of the Calandria tank. This is not realistic at all and may occur due to the lack of inlet flow momentum. To improve this, a new nozzle modeling was used, which can preserve both mass flow and momentum flow at the inlet nozzle. This resulted in a realistic temperature distribution in the tank. In conclusion, it was shown that the CUPID code is applicable to thermal-hydraulic analysis of the CANDU reactor moderator tank using the cost-effective porous media approach and that the inlet nozzle modeling is very important for the flow analysis in the tank.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.6
• /
• pp.18-28
• /
• 2016

Numerical analysis was conducted as a preliminary study for evaluating the dual bell nozzle. For future parametric studies, a dual bell nozzle was designed, and thereafter inlet condition, turbulence model, and the number of optimum grids were determined. Dual bell nozzle was designed based on the KSLV-II first stage nozzle. Inlet condition was determined to frozen flow model of non-reacting eight species by comparing with the design values. SST $k-{\omega}$ model turned out to be suitable as turbulence model. About 150 thousand of the grids were selected after grid sensitivity tests. Based on the results determined in this study, we plan to investigate performance gain of the KSLV-II by adopting a proposed dual bell nozzle.

• Nuclear Engineering and Technology
• /
• v.23 no.3
• /
• pp.340-351
• /
• 1991

Experimental studies were conducted on a l/5.03 scale reactor flow model of the Yong-gwang Nuclear Units 3 and 4. The purpose of the flow model test was to estimate the hydraulic effect in the reactor vessel due to the relative size difference between the ABB-CE's System 80 and the YGN 3&4 reactors. The flow model was designed according to the principle of similarity. Obtained from the test were the core inlet flow distribution, the core exit pressure deviations, and the segmental and overall pressure losses across the flow path from the reactor vessel inlet to outlet nozzle. These data will be used to provide input data for the core thermal margin analysis and to verify the analytical hydraulic design method.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.1
• /
• pp.16-27
• /
• 2018

A basic numerical analysis was performed to confirm the possibility of combining a dual bell nozzle and an Expansion-Deflection(E-D) nozzle. The dual bell nozzle was designed based on the first-stage nozzle of the Korean Space Launch Vehicle that is being developed, and the E-D nozzle concept was applied to the dual bell nozzle. The inlet condition was analyzed by applying eight types of frozen flow analysis, and k-${\omega}$ SST was selected as the turbulence model. The number of optimal grids was obtained as 240,000 through the grid sensitivity analysis. As a result, it was confirmed that the transition altitude increased owing to over-expansion when the E-D nozzle concept was applied to the dual bell nozzle, and the specific impulse gain was obtained at high altitudes compared with the KSLV-II first-stage engine.

• Transactions of the Korean hydrogen and new energy society
• /
• v.30 no.6
• /
• pp.585-592
• /
• 2019

In this study, a flashing boiling phenomenon of pressurized water jet was numerically studied and validated against an experimental data in the literatures. The volume of fluid (VOF) technique was used to consider two-phase behavior of water, while the homogeneous relaxation model (HRM) model was used to provide the velocity of phase change. During the flashing boiling through a nozzle, a mach disk was observed near nozzle exit because of pressure drop resulting from two-phase under-expansion. The flashing jet structure, local distributions of temperature/vapor volume fraction/velocity, and position of the mach disk were examined as nozzle inlet temperature changed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.8
• /
• pp.44-54
• /
• 2018

Stress and fatigue of the distributor, an equipment of the high-pressure evaporator for the HRSG, were evaluated according to ASME Boiler & Pressure Vessel Code Section VIII Division 2. First, from the results of the piping system analysis model, reaction forces of the tubes connected to the distributor were derived and used as the nozzle load applied to the detailed analysis model of the distributor afterward. Next, the detailed model to analyze the distributor was constructed, the distributor being statically analyzed for the design condition with the steam pressure and the nozzle load. As a result, the maximum stress occurred at the bore of the horizontal nozzle, and the primary membrane stress at the shell and nozzle was found to be less than the allowable. Next, for the transient operating conditions given for the distributor, thermal analysis was performed and the structural analysis was carried out with the steam pressure, nozzle load, and thermal load. Under the transient conditions, the maximum stress occurred at the vertical downcomer nozzle, and of which fatigue life was evaluated. As a result, the cumulative usage factor was less than the allowable and hence the distributor was found to be safe from fatigue failure.

• Transactions of the KSME C: Technology and Education
• /
• v.2 no.2
• /
• pp.73-80
• /
• 2014

Drug delivery in human upper airway was studied by the numerical simulation of oral airflow. We created an anatomically accurate upper airway model from CT scan data by using a medical image processing software (Mimics). The upper airway was composed of oral cavity, pharynx, larynx, trachea, and second generations of branches. Thin sliced CT data and meticulous refinement of model surface under the ENT doctor's advice provided more sophisticated nasal cavity models. With this 3D upper airway models, numerical simulation was conducted by ANSYS/FLUENT. The steady inspiratory airflows in that model was solved numerically for the case of flow rate of 250 mL/s with drug-laden spray(Q= 20, 40, 60 mL/s). Optimal parameters for mechanical drug aerosol targeting of predetermined areas was to be computed, for a given representative upper airways. From numerical flow visualization results, as flow-rate of drug-laden spray increases, the drag spray residue in oral cavity was increased and the distribution of drug spray in trachea and branches became more homogeneous.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.1
• /
• pp.10-17
• /
• 2001

In this paper are presented main power and gasdynamic characteristics of hypersonic test cell of Research Test Center (RTC) of Central Institute of Aviation Motors (CIAM). The distributions of temperature and Mach number at the exit of the aerodynamic nozzle of test cell are received at simulation conditions of flight at Mf=6. Values of available pressure difference and throttling characteristics for various operational modes of test cell, including the loading of working section by Scramjet model without the heating of air at entrance to the aerodynamic nozzle and with the heating of air, are received too.

• Clean Technology
• /
• v.25 no.4
• /
• pp.324-330
• /
• 2019

The selective catalytic reduction system is a highly effective technique for the denitrification of the flue gases emitted from the industrial facilities. The distribution of mixing ratio between ammonia and nitrogen oxide at the inlet of the catalyst layers is important to the efficiency of the de-NOx process. In this study, computational analysis tools have been applied to improve the uniformity of NH₃/NO molar ratio by controlling the flow rate of the ammonia injection nozzles according to the distribution pattern of the nitrogen oxide in the inlet flue gas. The root mean square of NH₃/NO molar ratio was chosen as the optimization parameter while the design of experiment was used as the base of the optimization algorithm. As the inlet conditions, four (4) types of flow pattern were simulated; i.e. uniform, parabolic, upper-skewed, and random. The flow rate of the eight nozzles installed in the ammonia injection grid was adjusted to the inlet conditions. In order to solve the two-dimensional, steady, incompressible, and viscous flow fields, the commercial software ANSYS-FLUENT was used with the k-𝜖 turbulence model. The results showed that the improvement of the uniformity ranged between 9.58% and 80.0% according to the inlet flow pattern of the flue gas.