• Journal of Advanced Navigation Technology
• /
• v.8 no.1
• /
• pp.49-57
• /
• 2004

In This paper the embedded linux based embedded control system was used and the tracking antenna system was studied for data link and communication between moving vehicles. A microprocessor based embedded controller is equipped with SA-1110 board and this embedded controller can control the azimuth and the elevation angle of the antenna. The relative position and attitude for pointing are calculated by using the GPS position signals from the moving vehicle. To verify the performance of the designed embedded antenna system, the orbit information of the Arirang satellite(from KARI) is used.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2023.07a
• /
• pp.505-506
• /
• 2023

본 논문은 임베디드시스템을 적용한 대용량 고부하 레이다 플랫폼의 구동 제어 방안을 제안한다. 군사적 방어 목적용 지대공 유도 미사일 시스템의 구성품인 다기능 레이다 시스템은 고중량의 안테나를 구동해야하는 대용량 고부하 레이다 구동 플랫폼이 필수이다. 이 다기능 레이다 시스템은 360도 방위각 전방향을 일정한 속도로 방위각 회전하며 감시정찰 및 방어 임무를 수행한다. 여기서 대부하 레이다 구동 플랫폼은 방위각회전 구동장치를 이용하여 일정한 속도로 360도 방위각 방향으로 안정적인 회전을 가능하도록 구동 제어한다. 본 구동 제어를 실시간으로 구현하기 위해 임베디드시스템인 DSP(Digital Signal Processor)가 포함된 제어모듈은 구동모듈에 회전구동 명령을 인가하여 일정한 회전각속도로 구동하도록 회전구동 모터를 실시간 제어한다. 고부하 레이다 플랫폼은 직구동모터타입의 회전구동모터, 회전체에 신호와 전원을 공급하기 위한 회전슬립링, 회전체의 회전각도를 측정하기 위한 회전센서로 구성된 방위각회전구동장치와 전체 전원을 공급받아 사용 목적에 맞게 변환하여 공급하는 전원모듈, 구동모터에 구동전원을 공급하기 위한 구동모듈, 회전구동 명령에 따라 구동제어하기 위한 제어모듈로 구성된 제어장치로 구분된다. 본 논문에서는 대부하 레이다 구동 플랫폼을 시뮬레이션 모델링으로 구현하고 제안하는 구동 제어 방안은 구동제어시뮬레이션으로 검증한다.

• Journal of Korea Society of Industrial Information Systems
• /
• v.11 no.5
• /
• pp.98-104
• /
• 2006

In this parer, proposed a Miniature inverted F Antenna for Bluetooth applications using folded structure and confirm it through producing and measurement. The proposed antenna as PIFA is optimized the impedance matching and the radiation pattern by positioning of feed line and short line. This antenna is designed with Microwave Studio presented CST and the optimized antenna structure is fabricated. The optimized miniature antenna size is 17.3 * 6 * 0.8 mm, the measured return loss bandwidth is 220MHz at 2.45GHz, the radiation pattern is quasi omni, and the gain is -1 dBi. these results are similar to the simulation data. It is comparatively appropriate for Bluetooth system.

• Journal of Korea Society of Industrial Information Systems
• /
• v.19 no.4
• /
• pp.17-24
• /
• 2014

In this paper, we propose a CMOS FM RX front-end structure with an automatic tunable input matching network and implement it using a 65nm CMOS technology. The proposed FM RX front-end is designed to change the resonance frequency of the input matching network at the low noise amplifier (LNA) according to the channel frequency selected by a phase-locked loop (PLL) for maintaining almost constant sensitivity level when an embedded antenna type with high frequency selectivity characteristic is used for FM receiver. The simulation results of implemented FM front-end show about 38dB of voltage gain, below 2.5dB of noise figure, and -15.5dBm of input referred intercept point (IIP3) respectively, while drawing only 3.5mA from 1.8V supply voltage including an LO buffer.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.8 no.2
• /
• pp.95-102
• /
• 2013

In this paper, we have studied the performance of the AOA (Angle of Arrival) in multi-antenna systems for LBS (Location Based Services) and we also analyzed the performance of the AOA in SISO (Single Input Single Output) in multipath environments and their differences. The adequacy of AOA positioning in new communication environments was determined. Currently used positioning methods in 3G communication environment has been developed based on SISO. However, the accuracy of SISO-based TOA (Time of Arrival), TDOA (Time Difference of Arrival), AOA positioning techniques degraded in multipath environments. The communication system will be changed and developed. According to enhanced positioning techniques are required. Using antenna characteristics and the phase difference between antennas of LTE-Advanced standard's key technique MIMO system AOA positioning, and SISO based AOA positioning performance were analyzed. We found that AOA technique potential for use based on Multiple antenna systems by computer simulations.

• Journal of Platform Technology
• /
• v.6 no.4
• /
• pp.59-68
• /
• 2018

The objective of this study is to develop an embedded antenna structure with NFC and WPC composite functions. By selecting stable materials, the optimal component ratio of the polymer sheet was determined. The low cost embedded winding method compared to the existing FPCB was devised. During the winding process, characterization and process technology were developed. We also fabricated a ferrite mold to process the WPC grooves and developed the process technology for optimizing the WPC antenna. The following conclusions were obtained. (1) Optimum composition ratio was derived as Fe 87.5%, Si 7%, Al 5.5% and selected as the final material. (2) Optimal sheet conditions were derived from the experimental evaluation method and the experimental design method through the combination test of the optimized sheet and the conventional mass production FPCB. (3) According to coil diameter and inner diameter, Q value fluctuation, resistance value and efficiency fluctuation are obtained. Therefore, the most suitable coil condition is selected and Rx matching is performed. (4) The EMV load modulation test and the cognitive distance test of the polymer sheet and the ferrite sheet showed that the recognition distance of the polymer sheet at 1k and 4K was 32-33 mm and the recognition distance of the ferrite sheet at the same condition was 30-31 mm.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.890-893
• /
• 2014

In this paper, we present a signal processing algorithm for a marine radar system, in which the evaluation of probability of collision as well as target detection and tracking are performed. Moreover, the digital signal processor that implements the algorithm is proposed. As simulation environment, a mechanically scanning antenna utilizing FMCW signal is used, conducting the beamforming operation with 1 degrees intervals. Test board consists of DSP chips and FPGA, which enable the implemented system to operate in real-time.

• Journal of Digital Contents Society
• /
• v.8 no.3
• /
• pp.323-328
• /
• 2007

Communication systems beyond 3G should provide more than 100 Mbps for wireless access. In addition to smart antennas, wireless multi-hop networks are proposed to increase the cell size and throughput. For example, Zigbee technology is expected to provide low cost and low power connectivity and can be implemented in wireless mesh networks larger than is possible with Bluetooth. Also, home embedded system using wireless mesh network is one of the key market areas for Zigbee applications. If the line-of-sight path is shadowed by home obstacles, a direct connection between the access point (AP) and the node is not possible at high frequencies. Therefore, by using multi-hop relay scheme the end node can be reached to AP. In this paper, the relaying of data between the AP and the end node is investigated and the throughput and PER(Packet Error Rate) are evaluated in multi-hop wireless mesh networks by using DSSS/BPSK system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.2
• /
• pp.93-98
• /
• 2018

This paper introduces the development of HF(NFC) and UHF band(13.56 MHz, 920 MHz) tag antennas, imbedded in a box. In dual band antennas, the HF band tag can be used to inspect the box using NFC, and the UHF band tag can be used for logistics. The dielectric constant of the box material is measured and used for simulation. The Ntag213 chip manufactured by NXP is used in HF loop antennas, since NFC is possible with Ntag213. For the UHF band, the Higgs-3 chip manufactured by Alien is used. The HF tag antenna is located at the center of the UHF tag antenna, and the location of the HF tag antenna is calculated while considering coupling effects. The designed tag can be used by both the bands for the purposes of logistics and authentication.