• Resources Recycling
• /
• v.14 no.5 s.67
• /
• pp.13-17
• /
• 2005

As a basic study for recycling molten converter slag as an ordinary portland cement (OPC) by a conversion process, the reaction mechanism and the rate of the formation of $C_4AF$ which is one of the main components of OPC were investigated. The converter slag whose basicity was controlled by adding reagent grade $SiO_2$ was melted and hold for 30 minutes in MgO crucible at $1300^{\circ}C{\sim}1350^{\circ}C$. Then, the sintered CaO pellet heated at the same temperature was dipped into the molten slag and hold for $10{\sim}30$minutes. After the reaction, the crucible was cooled in air and the specimen was cut off to the horizontal direction of the crucible. The dissolution rate of $C_3A$ pellet was measured by the change of radius of the sintered $C_3A$ pellet, and the formed phase of $C_4AF$ was observed by SEM/EDX. As a result, the dissolution rate of $C_3A$ pellet into molten slag was increased from $0.75{\times}10^{-4}(cm/sec)$ at $1300^{\circ}C$ to $1.67{\times}10^{-4}(cm/sec)$ at $1350^{\circ}C$, and the mixed layer of $C_4AF$ and $C_{12}A_7$ was found between slag and $C_3A$ pellet.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.299-299
• /
• 2007

후막형 무기 EL (electro-luminescence) 소자는 제조공정이 간단하고, 얇고, 가볍고, 유연한 동의 많은 장점들 때문에 휴대폰의 키패드 (key-pad) 및 광고용 back-light용으로 사용되고 있다. 이 무기 EL 소자는 비교적 손쉬운 스크린 프린팅 (screen-printing) 법으로 대면적을 제작할 수 있지만, LED (light emitting diode) 등과 비교하여 밝기가 낮아서 그 응용 분야가 제한되고 있다. EL 소자의 형광층은 전면 전극과 후면 전극 사이에 위치한다. EL은 이 형광층에 고 전기장이 걸릴 때, 전기장에 의해 가속된 전자가 형광층 내부에 첨가된 발광 중심의 전자를 여기시키고, 여기된 전자가 다시 바닥상태로 완화될 때 빛이 방출되는 현상이다. 즉, EL 소자는 이러한 전자 발광 현상을 이용한 소자로서, 전압 인가 시 발광 면 전체가 균일하게 발팡하는 평면 광원이다. 이러한 EL 소자에서 휘도의 증가는 후면 전극과 형광층 사이에 삽입되는 유전체 층의 특성과 밀접한 연관성이 있다. 본 연구에서는 고휘도 무기 EL 소자를 제작하기 위하여 이 유전체 층의 특성과 소자의 성능 사이의 관계를 알아보고자 하였다. 유전체 층에 사용하기 위해서 $BaTiO_3$-PVDF (polyvinylidene fluoride)의 복합체 필름을 제조하였다. 먼저 이 복합체 필름을 스크린 프린팅 (screen printing) 법으로 코팅하기 위한 페이스트 제작을 위해서, PVDF 수지를 용제에 녹였다. 그 다음, 일반 혼합기 및 삼단 롤밀 혼합기 (3-roll milling mixer) 등을 이용하여 $BaTiO_3$ 분말과 PVDF 용액을 다양한 비율로 혼합하여 페이스트를 제조하였다. ITO가 증착된 PET Film에 스크린 프린팅 법을 사용하여 형광층, 유전층, 배면 전극 등을 차례로 코팅하였다. $BaTiO_3$ (BT) 분말과 복합체 필름의 XRD 분석 결과, 분말 시료와 복합체 시료 모두 페로브스카이트 구조의 BT 회절선만 관찰되었다. 복합체의 단면 SEM 관찰에서는, BT 분말의 무게비가 증가할수록 더 치밀한 구조를 보여줌을 확인하였다. 또 EL소자의 유전상수와 휘도도 BT 분말의 혼합비가 증가할수록 증가하였다. 본 연구에서 제작한 무기 EL 소자의 최대 휘도는 약 $130\;cd/m^2$ 정도로 측정되었는데, 이는 휴대폰 키패드의 back-light용 광원으로 사용하기 충분하다고 판단되어진다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.12
• /
• pp.1573-1579
• /
• 2013

To test the performance of nuclear fuels, coolant needs to be circulated through the test rig installed in the test loop. Because the pressure and temperature of the coolant is 15.5 MPa and $300^{\circ}C$ respectively, coolant sealing is one of the most important processes in fabricating a nuclear fuel test rig. In particular, 15 instrumentation cables installed in a test rig pass through the pressure boundary, and brazing is generally applied as a sealing method. In this study, an induction brazing system has been developed using a high frequency induction heater including a vacuum chamber. For application in the nuclear field, BNi2 should be used as a paste, and optimal process variables for Ni brazing have been found by several case studies. The performance and soundness of the brazed components has been verified by a tensile test, cross section test, and sealing performance test.

• Food Science of Animal Resources
• /
• v.29 no.3
• /
• pp.340-348
• /
• 2009

A total of fifty Hanwoo steers raised from 14 to 29 months were used to investigated the effects of dietary mugwort on the performance and meat quality during refrigerated storage. A feeding trial was tested for 14.7 months and experimental diets included 0 and 2% dried wild mugwort. Total weight gain and average daily gain in this study were significantly higher in mugwort treatment than control treatment. Feed efficiency was improved by mugwort treatment compared with control treatment. Any difference in GOT (glutamic oxaloacetic transaminase), GPT (glutamic pyrubic transaminase), and BUN (blood urea nitrogen) was not observed between groups. Carcass weight and longissimus muscle area were higher for mugwort treatment than control. As fattening increased, total cholesterol in blood increased. Total cholesterol in blood tended to be lower in mugwort treatment than control treatment (p<0.05). The heating loss, $L^*$, $a^*$, $b^*$, chroma, and hue unit of all treatments were not affected treatment, but showed a significant decrease in all treatments during refrigerated storage. For fatty acid composition in longissimus muscle, dietary mugwort supplementation increased unsaturated fatty acid than saturated fatty acid (p<0.05). Based on these findings, it is obvious that supplementation of mugwort at 2% level will be useful to decrease cholesterol, increase unsaturated fatty acid, and improve growth performance of Hanwoo steers.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.1
• /
• pp.195-202
• /
• 2004

The shell due to the effect of initial normal pressures on the shell surface was based on the assumption that the directions of the pressures are always normal to the undeformed shell surface, and that the change in the surface area of the shell is negligible. But the fact that the pressure are always normal to the deforming surface leads "follower force". The follower effect in the analysis can significantly alter the solution for natural frequency and buckling load as compared to the case when the direction of the pressures are assumed to be normal to the uniform shell surface. The expression for the part of strain energy contribution from normal pressure due to the effect of follower force was derived and added to the element stiffness matrix of axisymmetric shell. In the case of increasing external pressure, the natural frequencies decrease until one of them reaches zero. Theoretically the smallest applied load that reduces the frequency of any mode to zero, will have same magnitude as that of the buckling load. In order to determine the bucking load of the shell a few sets of frequencies are computed and the results considering the follower effects are well with the exact solution while the case without that are quite different. But in case of hemispherical dome, there are little difference in buckling pressure between with and without the effect of follower force.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.2
• /
• pp.10-18
• /
• 2012

Most of studies on existing strengthening methods were mainly on increase of stiffness and strength of shear strengthening to rectangular beam. As concrete of beam and slab is poured simultaneously on the characteristics of construction in reinforced concrete beam-slab structure, adjacent slab uniformed after hardening has T-shaped beam cross section which makes the flange of beam, enhances the stiffness of the beam and widens the area supporting compressive strength, but available data of flexural behavior of T-shaped beam are lacking. In this research the T-shaped beams would be made, then the reinforced effects and structural properties can be estimated according to the kinds of reinforced materials and reinforced position. The conclusions are shown as below. To sum up the experimental results, The specimen which was reinforce by CB embedded inside of concrete indicated excellent resistive behavior, internal force and stiffness when it was destroyed. The steel plate reinforced specimen of stiffness and internal force were increase but it expressed lower reinforce effects because of lowering anchored force between concrete. Fiber sheet strengthening showed superior effects but the interfacial delamination was found due to the lack of anchored force in destruction. So the measure is needed now.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.24 no.6
• /
• pp.659-677
• /
• 2022

Hydrogen is emerging as a next-generation energy source and development and supply of FCEV (hydrogen fuel cell electric vehicle) is expected to occur rapidly. Accordingly, measures to respond to hydrogen car accidents are required and researches on the safety of hydrogen cars are being actively conducted. In this study, In this study, we developed a hydrogen car accident scenarios suitable for domestic conditions for the safety evaluation of hydrogen car in road tunnels through analysis of existing experiments and research data and analyzed and presented the hazard distance according to the accident results of the hydrogen car accident scenarios. The accident results according to the hydrogen car accident scenario were classified into minor accidents, general fires, jet flames and explosions. The probability of occurrence of each accident results are predicted to be 93.06%, 1.83%, 2.25%, and 2.31%. In the case of applying the hydrogen tank specifications of FCEV developed in Korea, the hazard distance for explosion pressure (based on 16.5 kPa) is about 17.6 m, about 6 m for jet fire, up to 35 m for fireball in road tunnel with a standard cross section (72 m²).

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.3
• /
• pp.1-8
• /
• 2019

Steel elevator pit was developed for the purpose of minimizing the excavation, simplifying the construction of the frame and economical efficiency by improving the problems that occurred in the existing reinforced concrete. It is common to apply conventional RC method through excavation to underground structures such as underground floor collector well and elevator pit. In recent years, the use of steel collector well and steel elevator pits to reduce construction costs by minimizing the materials of steel and concrete has been continuously increasing. The steel elevator pit is an underground structure and then the performance of the welding part and the structure system is important. Specimen with only steel plate and concrete without studs could support the load more than 3 times than the specimen with deck only. Therefore, even if there is no stud, the deck (steel plate) rib is formed and the effect of restraining the steel plate and the concrete during the bending action can be expected. However, since sudden fracture in the elevator pit may occur, stud bolt arrangement is necessary for the composite effect of steel plate and concrete. It is expected that the bending strength can be expected to increase by about 15% or more depending with and without stud bolts.

• Korean Journal of Heritage: History & Science
• /
• v.47 no.4
• /
• pp.58-73
• /
• 2014

In general, it is thought discoloration on wood is frequently found in decorative wood products. So this study was conducted focusing on white rot found lower parts of columns and baseboards of a wooden house, Hyunchungsa (shrine) to know whether microorganisms have any influence on discoloration or there is correlation with strength by investigating resistograph, occurrence of microorganisms and microscopy for analysis(SEM, tissue analysis etc.). The results obtained were as follows: (1) The result of measurement of resistograph showed there are little correlation between discoloration and strength though there was a spot indicating low resistance. (2) The moisture content of discolored part was relatively higher than that of normal parts, but occurrence of microorganisms was less in discolored parts while more kinds of microorganisms were identified in normal parts with high CFU(Colony Forming Unit). (3) The result of SEM (with a magnification of 500 times) on the surface of discolored parts, it was found out there are many kinds of particles in different sizes on the surface and those were composed of elements such as C, O, Si, Ca, and a small amount of Na and Cl (weight %) were detected in part. (4) The result of tissue analysis showed discoloration occurs limitedly to the outer surface of column. As these results, it is concluded that discoloration has nothing to do with strength, damage by microorganisms and salt.

• Journal of the Korea Convergence Society
• /
• v.10 no.9
• /
• pp.237-247
• /
• 2019

The purpose of this study was to evaluate the level and intensity of emotional labor of physical therapists and occupational therapists, and to identify the factors affecting them. Cross-sectional study was conducted on physical therapists and occupational therapists across the country using self-populated questionnaire. A total of 2,000 questionnaires were distributed to retrieve 1,500 questionnaires(75%), of which 1,374 questionnaires(68.7%) were finally analyzed, excluding 126 that answered duplicates or were missing answers. Multi-linear regression was performed to identify factors on the strength of emotional labor. According to the analysis results, high-risk groups in the areas under 'Emotional demand and regulation' and 'Overload and conflict in customer service' and 'Emotional disharmony and hurt' were 29.4%, 19.0% and 22.0% respectively, especially in 'Emotional demand and regulation', 'Overload and conflict in customer service', 'Emotional disharmony and hurt' for women working days, and 49% of daily work hours. Accordingly, we will be able to regularly screen physical therapists and occupational therapists for dangerous groups, and manage the intensity of emotional labor through the creation of a therapist's working environment, such as limiting overtime hours and assigning appropriate number of patients. Through this study, the grounds and methods for mitigating the negative effects of emotional labor and mediating emotional labor should be provided.