• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.12
• /
• pp.689-697
• /
• 2017

As a fundamental study to apply the new flocculation method using ballast in water treatment process, the optimal conditions for general and ballast coagulant dosage, and pH, which are known to have a significant influence, were derived by response surface methodology. Poly aluminum chloride (PAC) and magnetite ballast were used as a general coagulant and ballast, respectively. Coagulation experiments were performed by jar-tester using the kaolin based synthetic water. The effects of three independent variables (pH, PAC, and ballast) on response variables (turbidity removal rate and average settling velocity of flocs) and the optimum condition of independent variables to induce the optimum flocculation were obtained by 17 experimental conditions designed by Box-Behnken procedure. After performing experiments, the quadratic regression model was derived for each of response variables, and the response surface analysis was conducted to explore the correlation between independent variables and response variables. The $R^2$ values for the turbidity removal rate and the average settling velocity were 0.9909 and 0.8295, respectively. The optimal conditions of independent variables were 7.4 of pH, 38 mg/L of PAC and 1,000 mg/L of ballast. Under these conditions, the turbidity removal rate was more than 97% and the average settling velocity exceeded 35 m/h.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.1
• /
• pp.31-38
• /
• 2004

Mechanical design process is generally accomplished by design, analysis, and test. Designers use programs fitting purpose, and obtain repeatedly a response of a simulation program, a sub-program for optimization. In this paper, shape optimization using approximate optimization technique is carried out with sequential design domain(SDD). In addition, algorithm executing Pro/Engineer and ANSYS automatically are adopted in the approximate optimization program by SDD. It is difficult for design problem to be approximated accurately for the whole range of design space. However, more or less accurate approximation is constructed if SDD is applied to that case. SDD starts with a certain range which is off-seted from midpoint of an initial design domain and then SDD of the next step is determined by a move limited. Convergence criterion is defined such that optimal point must be located within SDD during the two steps. Also, the PLBA(Pshenichny-Lim-Belegundu-Arora) algorithm is used to solve approximate optimization problems. This algorithm uses the second-order information and the active set strategy, in order to seek the direction of design variables.

• Food Science and Preservation
• /
• v.10 no.3
• /
• pp.314-319
• /
• 2003

This study was conducted to the optimize salting process of eggplant for development new product and enhancement quality for export. Three variables by five level central composite design and response surface methodology were used to determine optimum conditions for salting time, temperature and salt concentration. Optimization of the process was conducted using the combination of the moisture content, salinity and color of surface and inside of salted eggplant. The regression polynomial model was suitable (P>0.05) by Lack-of-Fit analysis with highly significant. To optimize the process, based on surface response and contour plots, the individual contour plots of the response variables were superimposed. The optimum conditions for this process were 6 days and 15$^{\circ}C$ at 30％ concentration under the optimum of restricted variables as moisture content was below 84％, salinity was below 14％, L and b value of surface were 10 to 20 and below 0, L value and b value of inside were 70 to 75 and 16 to 18.

• Polymer(Korea)
• /
• v.30 no.6
• /
• pp.498-504
• /
• 2006

A suspension polymerization of styrene In aqueous phase was employed to study if polystyrene particles ranging from 1 to $20{\mu}m$ can be produced. Hydrophobic silica was selected as a stabilizer and azo-bisisobutyronitrile (AIBN) as an initiator. Polymerization reaction was carried out at a selected temperature in the range of $65{\sim}95^{\circ}C$. Stabilizer concentration was varied from 0.17 to 3.33 wt% compared to the water while the concentration of the initiator was raised from 0.13 to 6.0 wt% compared to the monomer. Dispersion of hydrophobic silica into the water phase was achieved by precise control of pH. Optimum dispersion of silica was obtained at pH 10. Average particle diameter decreased with increasing amounts of stabilizer concentration initially, exhibiting the minimum average diameter at 1.67 wt% of stabilizer concentration, after which it started to Increase. It is speculated that an excessive presence of stabilizer encouraged a secondary reaction in the reaction medium, which led to particle agglomeration, and as a result an increase in average particle diameter. Molecular weight was found to be independent of stabilizer concentration between 0.13 and 1.00 wt% whereas, it increased when stabilizer concentration exceeded 1.67 wt%. Variation of molecular weight was probably caused by the reduced activity and efficiency of initiator due to the high concentration of silica, and the secondary reaction in the reaction medium, as well. An increase in the Initiator concentration and/or reaction temperature resulted in an increase in both reaction rate and particle diameter. Consequently, we have confirmed that spherical polystyrene particles with $1{\sim}20{\mu}m$ in diameter can be prepared by careful selection of the concentration of stabilizer, initiator, pH and reaction temperature.

• The Journal of Korean Society for Radiation Therapy
• /
• v.25 no.1
• /
• pp.77-85
• /
• 2013

Purpose: The accurate movement of gantry rotation, collimator and correct application of dose rate are very important to approach the successful performance of Volumetric Modulated Arc Therapy (VMAT), because it is tightly interlocked with a complex treatment plan. The interruption and restart of dose delivery, however, are able to occur on treatment by various factors of a treatment machine and treatment plan. If unexpected problems of a treat machine or a patient interrupt the VMAT, the movement of treatment machine for delivering the remaining dose will be restarted at the start point. In this investigation, We would like to know the effect of interruptions and restart regarding dose delivery at VMAT. Materials and Methods: Treatment plans of 10 patients who had been treated at our center were used to measure and compare the dose distribution of each VMAT after converting to a form of digital image and communications in Medicine (DICOM) with treatment planning system (Eclipse V 10.0, Varian, USA). We selected the 6 MV photon energy of Trilogy (Varian, USA) and used OmniPro I'mRT system (V 1.7b, IBA dosimetry, Germany) to analyze the data that were acquired through this measurement with two types of interruptions four times for each case. The door interlock and the beam-off were used to stop and then to restart the dose delivery of VMAT. The gamma index in OmniPro I'mRT system and T-test in Microsoft Excel 2007 were used to evaluate the result of this investigation. Results: The deviations of average gamma index in cases with door interlock, beam-off and without interruption on VMAT are 0.141, 0.128 and 0.1. The standard deviations of acquired gamma values are 0.099, 0.091, 0.071 and The maximum gamma value in each case is 0.413, 0.379, 0.286, respectively. This analysis has a 95-percent confidence level and the P-value of T-test is under 0.05. Gamma pass rate (3%, 3 mm) is acceptable in all of measurements. Conclusion: As a result, We could make sure that the interruption of this investgation are not enough to seriously affect dose delivery of VMAT by analyzing the measured data. But this investigation did not reflect all cases about interruptions and errors regarding the movement of a gantry rotation, collimator and patient So, We should continuously maintain a treatment machine and program to deliver the accurate dose when we perform the VMAT for the many kinds of cancer patients.

• Clean Technology
• /
• v.25 no.4
• /
• pp.324-330
• /
• 2019

The selective catalytic reduction system is a highly effective technique for the denitrification of the flue gases emitted from the industrial facilities. The distribution of mixing ratio between ammonia and nitrogen oxide at the inlet of the catalyst layers is important to the efficiency of the de-NOx process. In this study, computational analysis tools have been applied to improve the uniformity of NH₃/NO molar ratio by controlling the flow rate of the ammonia injection nozzles according to the distribution pattern of the nitrogen oxide in the inlet flue gas. The root mean square of NH₃/NO molar ratio was chosen as the optimization parameter while the design of experiment was used as the base of the optimization algorithm. As the inlet conditions, four (4) types of flow pattern were simulated; i.e. uniform, parabolic, upper-skewed, and random. The flow rate of the eight nozzles installed in the ammonia injection grid was adjusted to the inlet conditions. In order to solve the two-dimensional, steady, incompressible, and viscous flow fields, the commercial software ANSYS-FLUENT was used with the k-𝜖 turbulence model. The results showed that the improvement of the uniformity ranged between 9.58% and 80.0% according to the inlet flow pattern of the flue gas.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.6
• /
• pp.26-32
• /
• 2016

Usually, there are many uncertainties regarding the error of an assumed load, material properties, member size, and structure analysis in a structure, and it may have a direct influence on the qualities of optimal design of structures. Probabilistic analysis has developed rapidly into a desirable process and structural reliability analysis is an increasingly important tool that assists engineers to consider uncertainties during the design, construction and life of a structure to calculate its probability of failure. This study deals with the applications of two optimization techniques to solve the reliability-based optimization problem of structures. The reliability-based optimization problem was formulated as a minimization of the structural volume subject to the constraints on the values of componential reliability index determined by the AFOSM approach. This presented method may be a useful tool for the reliability-based design optimization of structures.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.41 no.12
• /
• pp.1813-1822
• /
• 2012

The purpose of this study was to determine the optimal mixing conditions of two different amounts of purple barley flour ($X_1$), and olive oil ($X_2$) in baking white pan bread. The experiment was designed according to the central composite design of response surface methodology, which showed 10 experimental points including 2 replicates. The more purple barley flour added, the more weight, yellowness (b-value), hardness, gumminess, and chewiness increased; but the more volume, specific loaf volume, lightness (L-value), and springiness decreased. The greater the amount of olive oil added, the more hardness, cohesiveness, gumminess, and chewiness increased; but the more yellowness (b-value) and springiness decreased. The physical and mechanical properties were affected more by the amount of purple barley flour than by the amount of olive oil. Sensory properties except flavor were more affected by the amount of purple barley flour than by the amount of olive oil.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.7-7
• /
• 2017

범람파동 개념에 따르면 하도와 홍수터의 횡적 연결성은 하천 생태계의 생물다양성과 생산성 증대에 중요한 역할을 한다. 제방에 의하여 제내지 홍수터가 하도와 차단된 우리나라 하천에서 생태적 서비스를 증대하기 위해서 횡적 연결성을 복원하는 기술 개발이 필요하다. 횡적 연결성의 복원 기술을 개발하기 위해서는 우선 하도와 홍수터 사이에 생태적 연결성의 현황을 파악하고 연결성을 저해하는 요인을 진단하는 평가 기술 개발이 시급히 요청되고 있다. 따라서 본 연구에서는 제방에 의하여 차단된 제내지 하천환경에서 수리적, 생태적 횡적 연결성을 평가하고 진단하는 기술을 개발하고 연결성 회복 방안을 제안하고자 한다. 차단된 제내지 하천환경 평가는 1) 지리정보시스템을 이용하여 차단된 하천공간을 탐색하고, 2) 탐색된 전체 재내지에서 원격평가에 의하여 간편하게 횡적 연결성 평가를 실시하고, 3) 선정된 특정 제내지 대상지에서 현장평가에 의하여 상세하게 연결성을 평가하는 순서로 수행된다. 차단된 하천공간의 획정은 홍수가 범람할 수 있는 제내지 공간을 잠재적 하천공간으로 정의하고 수치표고모델 (DEM)과 하천기본계획의 30년 빈도 홍수위 자료를 이용하여 제내지 홍수터를 탐색하였다. 제내지 홍수터의 원격 연결성평가는 지리정보시스템에서 수치지도와 토지피복도 등 공간자료를 이용하여 수리 및 서식처 환경성, 제방 차단성과 하도 및 육상 연결성을 평가하고 원격평가 결과를 토대로 현장평가 대상지를 선정하였다. 횡적 연결성의 현장평가를 위하여 크게 하도-홍수터 연결성과 제내지 서식처 보존성으로 평가 항목을 선정하였다. 또한 연결성 평가는 수리연결성과 생물연결성으로, 서식처 보존성 평가는 습지유지율, 습지보존성, 육역지보존성을 세부항목으로 구성하였다. 평가 항목별로 5 등급의 평가 기준에 따라서 평가 점수를 부여하고 평가 총점을 산출하여 최종 연결성 평가 등급을 5 단계로 구분하였다. 현장평가를 위한 MS Access 기반 소프트웨어를 개발하여, 데이터 입력과 관리 및 평가 결과 산출과 비교를 편리하게 하였다. 개발된 제내지 하천환경 평가법을 청미천과 만경강에 적용하여 검증하였다. 개발된 평가법을 바탕으로 차단된 제내지 하천환경에서 연결성 회복에 따른 어류와 식생의 분포를 예측하는 수리생태 결합모델을 개발하였다. 먼저 차단된 제내지에서 연결 수로를 복원하여 유속, 수심 분포를 준이차 수리수문 모델로 예측하였다. 예측된 수리 환경에 따라서 지표어종의 서식처 적합도 지수 (HSI)를 이용하여 서식 분포 확률을 모의하였다. 또한 일반화가법모델 (GAM)을 이용하여 환경구배에 의한 우점식생의 분포를 예측하였다. 차단된 제내지 하천환경의 생태적 연계성 평가 기술을 기반으로 제방제거, 제방후퇴, 제방고 하강, 수문 및 연결수로 개선, 생물이동 저해 장벽 제거 등의 다양한 복원기술이 개발되어야 할 것으로 생각된다.

• Tuberculosis and Respiratory Diseases
• /
• v.60 no.6
• /
• pp.645-652
• /
• 2006

Objective: Patients with lung cancer have a relative high risk of developing secondary primary lung cancers. This study examined the additional value of autofluorescence bronchoscopy (AFB) for diagnosing synchronous lung cancers and premalignant lesions. Methods: Patients diagnosed with lung cancer from January 2005 to December 2005 were enrolled in this study. The patients underwent a lung cancer evaluation, which included white light bronchoscopy (WLB), followed by AFB. In addition to the primary lesions, any abnormal or suspicious lesions detected during WLB and AFB were biopsied. Results: Seventy-six patients had non-small cell lung cancer (NSCLC) and 23 had small cell lung cancer (SCLC). In addition to the primary lesions, 84 endobronchial biopsies were performed in 46 patients. Five definite synchronous cancerous lesions were detected in three patients with initial unresectable NSCLC and in one with SCLC. The secondary malignant lesions found in two patients were considered metastatic because of the presence of mediastinal nodes or systemic involvement. One patient with an unresectable NSCLC, two with a resectable NSCLC, and one with SCLC had severe dysplasia. The detection rate for cancerous lesions by the clinician was 6.0% (6/99) including AFB compared with 3.0% (3/99) with WLB alone. The prevalence of definite synchronized cancer was 4.0% (4/99) after using AFB compared with 2.0% (2/99) before, and the staging-up effect was 1.0% (1/99) after AFB. Since the majority of patients were diagnosed with advanced disease, the subjects with newly detected cancerous lesions did not have their treatment plans altered, except for one patient with a stage-up IV NSCLC who did not undergo radiotherapy. Conclusions: Additional AFB is effective in detecting early secondary cancerous lesions and is a more precise tool in the staging workup of patients with primary lung cancer than with WLB alone.