• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.6
• /
• pp.959-972
• /
• 2017

In evaluation of blast-induced vibration, peak particle velocity (PPV) is generally calculated by using attenuation relation curve. Calculated velocity is compared with the value in legal requirements or the standards to determine the stability. Attenuation relation curve varies depending on frequency of test blasting, geological structure of the site and blasting condition, so it is difficult to predict accurately using such an equation. Since PPV is response value from the ground, direct evaluation of the structure is impractical. Because of such a limit, engineers tend to use the commercial numerical analysis program in evaluating the stability of the structure more accurately. However, when simulate the explosion process using existing numerical analysis program, it's never easy to accurately simulate the complex conditions (fracture, crushing, cracks and plastic deformation) around blasting hole. For simulating such a process, the range for modelling will be limited due to the maximum node count and it requires extended calculation time as well. Thus, this study is intended to simulate the elastic energy after fractured zone only, instead of simulating the complex conditions of the rock that results from the blast, and the analysis of response characteristics of the velocity depending on shape and size of the fractured zone was conducted. As a result, difference in velocity and attenuation character were calculated depending on fractured zone around the blast source appeared. Propagation of vibration tended to spread spherically as it is distanced farther from the blast source.

• Food Science and Preservation
• /
• v.13 no.5
• /
• pp.555-562
• /
• 2006

This study was conducted to investigate the rheological properties of protein-bound polysaccharide powders (SD-1, 2, 3) using ultrafiltration (UF) and spray drying (SD) process from Agaricus blazei Murill. The calculated weight-average molar mass (Mw) in the positions at 29.7 mL (for SD-1), and at 27.8 mL (for SD-2), and at 18.7 mL (for SD-3) was $8.2{\times}10^3,\;9.6{\times}10^4$, and $5.9{\times}10^6g/mol$, respectively. As concentration increased the solution showed higher pseudoplasticity where the pseudoplasticity decreased as temperature increased. The flow behaviors of spray dried powder solutions were more fitted to Herschel-Bulkley equation than Power law equation. Apparent viscosity of SD-2 was more temperature-dependent than that of SD-1 and 3. However, the SD-3 tended to be more concentration-dependent than SD-1 and 2 as temperature increasing.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.1
• /
• pp.61-68
• /
• 2010

Purpose: This article attempted to determine the factors affecting the preload and screw loosening. Methods: Available clinical studies from 1981 to 2008 from the PUBMED that presented screw loosening data and review articles regarding screw joint stability were evaluated. Eleven studies dealing the biomechanical principles of the screw mechanics were reviewed. Moreover, the results of our data were included. Results: The frequency of screw loosening was consequently reduced due to the advancement in torque tightening with torque wrench, screw material, coating technique for reducing the frictional force, and thread design, etc. If preload in the screw falls below a critical level, joint stability may be compromised, and the screw joint may fail clinically. The types of fatigue failure of screw were divided to adhesive wear, plastic deformation, and screw fracture. Conclusion: An optimum preload is essential to the success of the implant-abutment complex. To maintain optimum preload, using a torque wrench and re-tightening at recall time were needed.

• Nuclear Engineering and Technology
• /
• v.21 no.2
• /
• pp.111-122
• /
• 1989

With the Zircaloy-4 tube oxidized in high temperature (1323 K) steam for 5, 10, 30 and 60 minutes, the expanding copper mandrel test was carried out over a temperature range of 673-l173k at $\varepsilon\;=\;3.0\times10^5S\;^1$. The oxidation parameters $(K_i)$ in the present study were linearly proportional to square root of time $(Ki= \delta_{kit})$ and their rate constants ($\delta_{ki}$) are 0.281, 2.82, and 2.313 for weight gain and thickness of Zr02 and $\alpha$(0) layer, respectively. Activation energy for high temperature (873-1073k) plastic deformation of Zircaloy-4 increases from 251 KJ/mol to 323 KJ/mol with increase in oxidation time from 5 minutes to 60 minutes due to the high strengthened Zr02. With the oxide layer thickness [K ; expressed in "Equivalent Cladding Reacted" (ECR,%)] and the yield stress obtained from the mandrel test, an empirical relation was derived as ($\sigma/C)^n=K^mexp$ (Q/RT) with n=6.9, m=5.7, C=0.155, 0.138, 0.051, and 0.046 MPa for Q=251, 258, 316, 323 KJ/mol, respectively.

• Journal of Life Science
• /
• v.17 no.11
• /
• pp.1488-1491
• /
• 2007

An epulis was occurred on gingiva of 11-year old female dog, Yorkshire terrier. Our case had feature of ossifying epulis but there were a few multi-nucleated giant cells (MGCs). MGCs had osteoclast-like appearance and giant cell epulis usually appears at the site of tooth extraction. Therefore, we suggest that appearance of MGCs in our case may be due to phagocytosis pre-formed osteoid/bone or our case may be mixed epulides of ossifying and giant cell epulis by mixed stimulation of chronic gingivitis and trauma and in flammation by tooth extraction. Thus, MGCs have possibility enough to appear in ossifying epulis, but ossifying epulis accompanying MGCs has not been reported. Therefore, our case may deserves an attention as an unique case and will be helpful to study pathogenesis of giant cell containing lesion of the jaw.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.3
• /
• pp.245-252
• /
• 2017

Recently, structures such as large retailers, outlets and warehouses have been increasing in accordance with changes in consumption patterns. Since these structures include ultra-flat slab members, they are thoroughly managed to control slab cracking by the plastic and drying shrinkage. In order to control the cracking of the slab member, a chemical crack reduction method is used. In particular, the use of the shrinkage reducing agent has been examined. However, domestic research results are limited. In this study, the shrinkage properties of concrete using shrinkage reducing agent and the drying shrinkage properties according to the mixing factors were investigated. The performance of domestic shrinkage reducing agent was appeared similar to that of overseas high-grade shrinkage reducing agent. As the shrinkage reducing agent usage increased, the drying shrinkage reduction effect increased. At the age of 100 days, the dry shrinkage rate of specimen with the shrinkage reducing agent of 1.5%was shown about half that of the specimen without the shrinkage reducing agent. The shrinkage reducing agent was gound to have no specific performance change for the use of the admixture.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.5
• /
• pp.995-999
• /
• 2007

The lead zirconate titanate (PZT) powders were synthesized to make the piezoelectric ceramics in low temperature as low as $900^{\circ}C$. To investigate the influence of additives on sintering of PZT, two kinds of sintering aids were made as follows; $wB_2O_3-xBi_2O_3-zCuO$and LiBiO2-CuO. The sintering aid, $1{\sim}3$ wt.% $LiBiO_2-CuO$, was added into these PZT powders and the specimens were fired at temperature in the range of $800{\sim}1200^{\circ}C$. The highest density was shown in the specimen with 1 wt.% $LiBiO_2-CuO$ as additive at temperature of $900^{\circ}C$. The sintered specimen were analyzed by X-ray diffraction(XRD) and scanning electron microscopy (SEM) was utilized to observe the microstructure, especially the densified morphology of specimens. In the XRD pattern, the well-crystallized PZT phase could be obtained in consequence of firing at $900^{\circ}C$. The scanning electron microscopy(SEM) was utilized to observe the structure of specimens after firing at $900^{\circ}C$. The densified perovskite structure of $PbZrTiO_3$ could be obtained by sintering at temperature as low as $900^{\circ}C$. The high sinterability of PZT ceramics was attributed to the low formation temperature of the liquid phase of additives.

• Archives of Plastic Surgery
• /
• v.37 no.4
• /
• pp.415-420
• /
• 2010

Purpose: Heterotopic calcification is a pathological event in which deposits of calcium salts build up, usually in the joint area or soft tissues. It can occur under many conditions and in some rare cases may develop in burn scars. In particular, ulcerations in burn scars accompanied by heterotopic calcification are difficult to treat through conservative treatment. This study reports methods for accurate diagnosis and adequate treatment of ulceration in burn scars accompanied by heterotopic calcification. Methods: Fourteen patients who visited our hospital from March 2008 to January 2010 were subjected to this study. Their sex, age, modes of burn, degree, TBSA (%), ulcerated area, the time of occurrence of the ulcerations in the burn scars were investigated. In addition, radiological examination and biopsy was performed to diagnose heterotopic calcification. Results: Among the 14 cases, 6 were male and 8 were female. The average age of the patients was 48.2 (27 - 69 yrs). As for the mode of burn, 11 were flame burns and 3 were scalding burns. The average time of occurrence of the ulcerations in the burn scars was 4.5 months. The ulcerated areas were situated in the legs in 12 cases, arms in 1 case, and torso in 1 case. The diagnosis was confirmed through X-ray and biopsy, and skin graft was performed after wide excision. Conclusion: Diagnosis of the ulceration in burn scars accompanied by heterotopic calcification is possible through radiological and pathologic studies. Surgical treatment is the most reliable method of treatment, and we chose to perform skin graft after wide excision. Also, we learned that the complete removal of the calcified tissue and the inflammatory fibrotic tissues is crucial in preventing recurrence. Also, in contrast to Marjolin's ulcer, heterotopic calcification had a small size, little or no granulation tissue, and lacked fungating type ulceration. Therefore, favorable prognosis could be achieved through adequate treatment.

• Journal of Veterinary Clinics
• /
• v.31 no.6
• /
• pp.515-518
• /
• 2014

A castrated male Yorkshire Terrier dog was presented for urinary incontinence and constipation. On physical examination, the dog showed difficult urination. There were no neurological abnormalities and no bacterial detection on urinalysis. Rectal examination revealed a regular, normal-sized prostate. Urethral catheterization was performed easily. Excretory urography and retrograde positive contrast urethrocystography showed displacement of the urinary bladder to the intrapelvic region. There was no evidence of an ectopic ureter. A tentative diagnosis of urethral sphincter mechanism incompetence accompanied with a pelvic bladder was made. Cystopexy was decided to place the urinary bladder to its normal position. The neck of the urinary bladder was anchored to the body wall and prepubic tendon using mattress sutures. Additional sutures were placed to appose the lateral part of the urinary bladder and abdominal wall. A simple interrupted suture was placed to tack the apex of the urinary bladder on the abdominal incision line. A urinary catheter was placed in the urinary bladder to provide post-operative evacuation. The catheter was removed when the dog was able to urinate with minimal straining at 3 days post-operatively. The owner reported that the dogs showed normal urination without straining at 3 days after the catheter was removed. Excretory urography revealed that the urinary bladder was located on its normal position at 2 months post-operatively. Subsequent communication with the owner by telephone revealed that the dog was in good urination at 3 years 11 months post-operatively.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.33 no.6
• /
• pp.1022-1027
• /
• 2004

The monacolin K content was determined to investigate the stability of monacolin K from red yeast rice after heating (20∼8$0^{\circ}C$), adjusting the pH (2∼8) by adding 3 N HCl or 3 N NaOH, adding the organic acid (6.0% acetic acid, 0.6% citric acid, 1.5% lactic acid) to pH 4.0 and adding the water (0∼80%). And the monacolin K was isolated from red yeast rice by conducting open column chromatography using neutral aluminum oxide. As a result, the stability of monacolin K decreased with increasing the temperature. The stability for pH was in the order of the unadjusted pH (pH 5.9)>8>4 and pH 2>10. The stability for organic acid was high in the order of lactic acid>citric acid>acetic acid, and the stability of monacolin K under acid was different according to the acid type. The degradation rate of monacolin K increased with increasing the water content. Moreover monacolin K was able to isolate from red and pink pigments as well as the other noncoloric compounds in red yeast rice. The yield of monacolin K was found to be 70%.