• Journal of Ocean Engineering and Technology
• /
• v.7 no.1
• /
• pp.3-12
• /
• 1993

용접부의 파괴특성을 J-적분을 이용하여 유한요소법으로 해석하였다. 용접부 의 열전달 해석 및 응력해석을 수행한후 crack을 도입하여 crack 주위의 자류응력 해석을 통하여 crack tip에서의 J- 적분치를 계산하였다. 이차원 및 삼차원에서의 파괴해석을 위한 modeling 과정을 소개하였으며 대표적인 계산결과를 소개하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.10 no.2
• /
• pp.91-102
• /
• 1990

The representative tests in this study are performed at a selected site which has the soil layers to analyze the safety and economy of the dynamic analysis for the variable soil conditions. Crosshole test and downhole test of small strain level tests and triaxial test of large strain level test are performed in the soil layers, and in the rock layers, crosshole test and downhole in-situ tests and laboratory sonic test are performed to measure the dynamic shear modulus, damping ratio, and Poisson$\acute{s}$ ratio of the soil and the rock. The correlations between the dynamic soil properties from the tests and the basic soil properties are determined through the regression analysis. The representative design value of the soil is determined by probability analysis of the test results. It is determined from the nonlinear stress-strain model in soils, and the value at small strain level is computed in rocks according to the distribution of the type of soils and the affecting variables. The constitutive value is systematized to be utilized in the analysis of the test results, and computation of the input soil data.

• Korean Journal of Materials Research
• /
• v.7 no.11
• /
• pp.951-956
• /
• 1997

Vacuum Hot Pressing을 이용하여 제조한 TiNi형상기억섬유 강화 6061 AI기지 복합재료를 제조하고 미세조직 및 기계적 특성 등을 연구하였다. 제조된 복합재의 항복응력은 예비변형량, 섬유체적율 및 열처리에 따라 증가하였다. 복합재의 지적특성은 예비변형이 가하여진 후 재가열되었을 때 기지 내 TiNi 섬유의 형상기억효과에 의한 압축잔류응력 발생에 기인된다. 미세조직 관찰 섬유와 기지 사이에는 AI$_{3}$Ti및 AI$_{3}$Ni의 금속간화합물층이 관찰되었다. 또한 시험온도 증가와 더불어 TiNi섬유강화된 복합재의 유동강도는 높은 값을 나타내었다.

• Journal of the Korea Concrete Institute
• /
• v.23 no.1
• /
• pp.77-86
• /
• 2011

The concrete creep deformation of a hybrid composite section can cause additional deformation of the composite section and the stress relaxation of pre-compressive stress on the concrete section due to partial restraint of the deformation. In this study, the stress relaxation coefficient method (SRCM) is derived for simple analysis of complicate hybrid or composite sections for engineering purpose. Also, an equation of the stress relaxation coefficient (SRC) required for the SRCM is proposed. The SRCM is derived with the parameters of a creep coefficient, section and loading properties using the same method as the constant-creep step-by-step method (CC-SSM). The errors of the SRCM is improved by using the proposed SRC equation than the average SRC's which were estimated from the CC-SSM. The root mean square error (RMSE) of the SRCM with the proposed SRC equation for concrete with creep coefficient less than 3 was less than 1.2% to the creep deformation at the free condition and was 3.3% for the 99% reliability. The proposed SRC equation reflects the internal restraint of composite sections, and the effective modulus of elasticity computed with the proposed SRC can be used effectively to estimate the rigidity of a composite section in a numerical analysis which can be applied in analysis of the external restrain effect of boundary conditions.

• International Journal of Highway Engineering
• /
• v.10 no.1
• /
• pp.49-62
• /
• 2008

This paper presents the results of a study that was performed to evaluate the characteristics of deformation under repeated loadings in unbound geomaterials of pavements. Two important parameters, resilient and permanent deformation were estimated using the repeated load triaxial test. In addition, the effects of different stress state and environmental conditions with various materials were evaluated. Due to the locking mechanism and resiliency of unbound geomaterials, a consistent increase in permanent deformation on unbound geomaterials was observed and the asymptotic condition is slightly reached. In conclusion, the results show that selected models and parameters are satisfactory to predict permanent deformations after a certain number of loadings.

• Journal of the Korean Magnetics Society
• /
• v.1 no.2
• /
• pp.42-48
• /
• 1991

The basic soft magnetic characteristics of a typical Fe based amorphous $Fe_{80}B_{15}Si_{5}$ alloy were measured with pulse metheod. Quantitative relations between magnetostriction, anisotropy energy, reluctivity were investigated. The relative contribution factor of magnetostrictive and uniaxial anisotropy energy to the reluctivity were calculated. The internal stress and induced anisotropy were estimated. A tension applied to the long axis of the sample greatly enhanced induced anisotropy.

• Journal of Korean Association for Spatial Structures
• /
• v.9 no.2
• /
• pp.77-82
• /
• 2009

ETFE is the abbreviation of Ethlene Tetra Fluoro Ethlene, a sort of colorless and transparent granules. The advantage of ETFE film has chemical resistance, anti-stick property, very lightly material. The thickness of ETFE film is used to from 50 ${\mu}m$ to 300 ${\mu}m$ and have superior ability of daylight transmission and elongation, while the strength is lower than of fabric membrane. The tensile strength of ETFE film changes from 40Mpa to 60Mpa and the tensile strain at break can get to about 300-400%. The mechanical characteristic test of ETFE film is described in this paper. The tensile strain at break, the tensile strength and the stress-strain curve are obtained from the test. And then it was analyzed stress-strain characteristic by temperature and mechanical characteristic by cycling load.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.1
• /
• pp.27-33
• /
• 2011

In general, the shear strength of a clay specimen under the direct shear test and the triaxial compression test increases with an increase in the shear rate. This study investigates the effects of shear rate and silt content on the stress-strain behavior of remolded Gwangyang clay, by changing the shear rate and the silt content. Based on the results of the triaxial compression tests, the equi-strain line of remolded Gwangyang clay shows initially positive slope and then becomes flat at certain strain level. As the strain level where the equistrain becomes flat is different depending on the soil with different silt contents, this can be considered as the inherent property of soil.

• Magazine of the Korea Concrete Institute
• /
• v.4 no.1
• /
• pp.107-118
• /
• 1992

In order to examine the mechanical properties of carbon fiber reinforced cement composites with silica powder PAN - based carbon fiber and Pitch- based carbon fiber, and polymer impregnators experimental studies on CFRC impregnated in polymer were carried out. The effects of types, length, and content~i of carbon fibers and matrices of fresh and hardened CFRC impregnated in polymer were examined. The test results show that compressive, tensile, and flexural strength of CFRC impregnated in polymer were much more iriCreased than those of air cured and autodaved CFIIC CFRC impregnated in polymer was also considerably effective in improving toughness, freeze thaw resistance, loss of shrinkage, and creep resist ance, compared with air cured and autoclaved CFRC.

• Journal of the Korean Society for Railway
• /
• v.11 no.1
• /
• pp.61-68
• /
• 2008

Resilient modulus has been used for characterizing the stress-strain behavior of subgrade soils subjected to traffic loadings. With the recent release of the M-E Design Guide, highway agencies are further encouraged to implement the resilient modulus test to improve subgrade design. The subgrade design for the trackbed, however, is primarily relying on the static test results such as $K_{30}$ and deformation modulus, Ev. Therefore applicability of the resilient modulus for the design of trackbed needs to be evaluated. In this study, physical property tests, unconfined compressive tests and resilient modulus tests were conducted to assess the resilient and permanent strain behavior of 14 cohesive subgrade soils. A predictive model for estimating the resilient modulus is proposed based on the results of unconfined compressive tests and tangent elastic modulus, unconfined compressive strength, failure strain, secant modulus at peak, and yield strain. The predicted resilient moduli using the predictive models compared satisfactorily with measured ones. Although the permanent strain occurs during the resilient modulus test, the permanent behavior of subgrade soils is currently not taken into consideration.