• The Korean Journal of Rheology
• /
• v.6 no.1
• /
• pp.49-59
• /
• 1994

높은 전기장 하에서 다분산, 비구형 실리카/실리콘 오일 현탁액의 전기유변 (electrorheological, ER)현상을 살펴 보았다. 전기유변유체는 전기장 방향으로 사슬구조를 형 성하는 특성을 보이며 이것이 유변물성의 향상에 기여하는 것으로 알려졌다. 동적(dynamic) 상태 실험에서 전기장 하의 실리카 현탁액은 매우낮은 임계변형율(${\gamma}$c =0.1%)이상에서 비선 형 점탄성을 보였다. 저장탄성계수(G＇)는 변형율 변화에 손실탄성계수(G＂)는 매질의 점도 에 더 민감한 의존성을 보였다. 또한 겉보기 항복응력은 입자의 부피분율과 전기장에$\Phi$1.9E1.4 의 의존성을 보였는데 부피분율에 대한 의존성이 큰 이유는 0.1 이상의 부피분율에서 복합 사슬 구조 내의 입자들 간의 상호 정전효과가 지배적으로 나타나기 때문이라고 생각된다. 정상상태 실험에서는 부피분율이 크거나 높은 전기장 하에서 전단속도가 0.1sec-1 정도 이하 로 감소함에 따라 전단응력이 급겨히 증가하는 현상을 보였다. 그러므로 본질적인 동적 항 복응력을 얻기 위해서는 매우 낮은 전단속도 영역의 특이한 응력거동을 고려해야한다. 큰 전단속도 하에서는 hydrodynamic interaction의 영향으로 전단속도의 증가에 따라 전단응력 이 증가하였다. 이같은 전단응력의 거동을 계단전단실험으로 확인하였다.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.7
• /
• pp.73-80
• /
• 2005

There are several major practical consequences of stress-dependent properties of unbound pavement foundations. Among those are the stress-dependent modulus and Poisson's ratio's that may change, the compressive stresses that are generated in materials under load, the stiffening and strengthening effect of repeated loading to progressively increase the unbound pavement materials resistance to permanent deformation. In order to study these, the algorithm for predicting deformations on conventional flexible pavements are proposed and the stress-dependent effects on layer deformation are presented in this paper by the developed stress-dependent finite element analysis program with the selected models.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.4
• /
• pp.337-343
• /
• 2000

Prism plane slip {11$\bar{2}$0}1/3{$\bar{1}$120} location velocity in sapphire ($\alpha$-Al$_2$O$_3$) single crystals was measured by etch-pit method. The dislocation velocities were measured as a function of temperature and stress between $1150^{\circ}C$ and $1400^{\circ}C$ for engineering stresses in the range 140 to 250 MPa. The dependence of temperature and stress in dislocation velocity was investigated. The activation energy for dislocation velocity was determined to be 4.2$\pm$0.4 eV. On the other hand, the stress exponent (m) describing the stress dependence of dislocation velocities was in the range of 4.5$\pm$0.8. Through this experiments, it was reconfirmed that the basal plane in sapphire single crystals has the 3-fold symmetry.

• Proceedings of the KWS Conference
• /
• 2002.05a
• /
• pp.171-174
• /
• 2002

• Tunnel and Underground Space
• /
• v.23 no.5
• /
• pp.383-391
• /
• 2013

A number of true triaxial tests on rock samples have been conducted since the late 1960 and their results strongly suggest that the intermediate principal stress has a considerable effect on rock strength. Based on these experimental evidence, various 3-D rock failure criteria accounting for the effect of the intermediate principal stress have been proposed. Most of the 3-D failure criteria, however, are focused on the phenomenological description of the rock strength from the true triaxial tests, so that the associated strength parameters have little physical meaning. In order to confirm the likelihood that the intermediate principal stress dependency of rock strength is related to the presence of weak planes and their distribution to the preferred orientation, true triaxial tests are simulated with the transversely isotropic rock model. The conventional Mohr-Coulomb criterion is extended to its anisotropic version by incorporating the concept of microstructure tensor. With the anisotropic Mohr-Coulomb criterion, the critical plane approach is applied to calculate the strength of the transversely isotropic rock model and the orientation of the fracture plane. This investigation hints that the spatial distribution of microstructural planes with respect to the principal stress triad is closely related to the intermediate principal stress dependency of rock strength.

• Applied Biological Chemistry
• /
• v.33 no.4
• /
• pp.301-306
• /
• 1990

The Physical and chemical properties or dry acorn starch(DS), detannined acorn starch (DTS) and defatted and detannined acorn starch(Drn) were investigated. Ail acorn starch sample, observed by a scanning electron microscope, showed a hemispherical shape ud its size was about $5{\sim}10{\mu}m$ in diameter. It had a little change on the pasting temperature of DS, DTS and DFTS but peak viscosity of DTS was somewhat higher than that of n. Flow behavior of gelatinized starch pastes showed a pseudoplastic behavior and flow behavior index was lower than unit. The consistency coefficient showed concentraion and temperature dependency. The activation energies of DS, DTS and DFTS were $2.09{\sim}3.58Kcal/g\;{\cdot}\;mol and time dependent characteristic of acorn starch samples showed thixotrpic behavior.

• Tunnel and Underground Space
• /
• v.22 no.6
• /
• pp.462-470
• /
• 2012

Implementing the generalized Hoek-Brown failure criterion in the framework of the Mohr-Coulomb criterion requires the calculation of the equivalent friction angle and cohesion. In the conventional method based on the Balmer (1952)'s theory, the tangential instantaneous friction angle and cohesion are expressed in terms of the minimum principal stress ${\sigma}_3$, which does not provide the information about the dependency of the equivalent parameters on the hydrostatic pressure and the stress path. In this study, this defect of the conventional method has been overcome by representing the equivalent parameters in terms of stress invariants. Through the example implementation of the new method, the influence of the magnitude of the hydrostatic pressure and the Lode angle on the tangential instantaneous friction angle and cohesion is investigated. It turns out that the tangential instantaneous friction angle is maximum when the stress condition is triaxial extension, while the tangential cohesion is maximum when the stress condition is triaxial compression. The dependency of the equivalent Mohr-Coulomb strength parameters on the hydrostatic pressure and the Lode angle tends to be more substantial for the favorable rockmass of larger GSI value.

• Korean Journal of Materials Research
• /
• v.11 no.3
• /
• pp.221-226
• /
• 2001

The basal slip (0001)1/3<1120 > dislocation velocity in sapphire ($\alpha$-$Al_2$$O_3$) single crystals was measured by four-point bending test. The bending experiment was carried out in the temperature range from 120$0^{\circ}C$ to $1400^{\circ}C$ at various engineering stresses 90MPa, 120MPa, and 150MPa. The velocity of such dislocations was estimated from the bending displacement rate of the four-point bend sample. The dependence of temperature and stress in dislocation velocity was investigated. The activation energy for dislocation velocity was determined to be about 2.2$\pm$0.4eV. In addition, the stress exponent (m) describing the stress dependence of dislocation velocities was in the range of 2.0$\pm$0.2.

• Tunnel and Underground Space
• /
• v.21 no.2
• /
• pp.117-127
• /
• 2011

The purpose of this study is to demonstrate the effect of in-situ rock stresses on the deformability and permeability of fractured rocks. Geological data were taken from the site investigation at Forsmark, Sweden, conducted by Swedish Nuclear Fuel and Waste Man-agement Company (SKB). A set of numerical experiments was conducted to determine the equivalent mechanical properties (essentially, elastic moduli and Poisson's ratio) and permeability, using a Discrete Fracture Network-Discrete Element Method (DFN-DEM) approach. The results show that both mechanical properties and permeability are highly dependent on stress because of the hyperbolic nature of the stiffness of fractures, different closure behavior of fractures, and change of fluid pathways caused by deformation. This study shows that proper characterization and consideration of in-situ stress are important not only for boundary conditions of a selected site but also for the understanding of the mechanical and hydraulic behavior of fractured rocks.

• The Korean Journal of Rheology
• /
• v.9 no.1
• /
• pp.16-26
• /
• 1997

사출 성형된 제품에서 발생하는 잔류응력은 최종 제춤의 기하학적 정밀도와 기계적 성질 및 열적 성질에 영향을 미친다. 사출성형된 제품의 잔류응력을 예측하기 위해서는 먼 저 열 및 유동장의 해석을 수행하여야 하고이를 위해서는 사출 성형의 세단계. 즉 충전, 보 압, 냉각을 모두고려해야한다. 검사체적 방법에 기초한 혼합 유한요소/유한차분방법을 사용 하는 수치 해석적 기법에 의하여 충전과정가 후충전 과정의 유동장 해서을 수행하였다. 일 반화된 헬레쇼 유동을 가정하였고 보압과 냉각과정시의 고본자의 압축성을 고려하였다. 점 도의 전단 변형률의 크기와 온도에 대한 의존성은 개선된 크로스 모델을 사용하여 나타내었 다. Tait에 의해 제안된 상태방정식은 고분자의 온도, 압력, 부피의 상호관계를 묘사하는 좋 은 방법을 제공하였다. 유동해석을 통하여 전 공정에 걸쳐서 온도와 압\ulcorner장의 변화에 대한 데이터를 얻었고 제품의 고체 응력해석의 입력 데이터로 사용하였다. 유한요소응력해석에는 평면 응력요소를 사용하였다. 다양한 형태의 금형에 대해서 공정 변수들을 달리하여 유동장 의 해석과 잔류응력의 계산을 수행하였다. 이로부터 공정조건과 유동장의 관계를 밝히고 최 종 제춤의 잔류 응력에의 영향을 고찰하였다.