• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.101-104
• /
• 2000

본 논문은 중거리 수중표적이 고정 설치된 수신기에 접근 시 표적신호의 다중경로에 신호변형을 일으키며, 특히 신호의 변형 중 도플러효과를 변화정도를 신호모의를 동하여 분석하였다. 동해의 동계와 하계의 대표적인 음속구조에 따른 고유음선(eigenray)의 도플러 주파수를 계산하였다. 수중표적의 속도는 12노트, 주파수는 135Hz, 350Hz, 신호는 정현파로 가정하여 신호모의를 하였다. 그 결과 해저면 반사가 한번인 음선은 수신신호에 주로 Vp-doppler를 형성하였고 두 번인 음선은 주로 Down-doppler를 형성하였다.

• Proceeding of EDISON Challenge
• /
• 2013.04a
• /
• pp.327-330
• /
• 2013

Converging-diverging 노즐은 시스템 내부 유동에 적용되는 속도면적 법칙을 통해, 아음속 유동을 초음속으로 만드는 장치이며, 항공기 엔진 등에서 추력을 얻기 위해 쓰인다. 이상기체, 등 엔트로피를 가정한 동일 입구 조건에서, 출구로 빠져나오는 유동의 속도는 오직 면적 비에만 관계한다. 그러나 실제현상에서는, 출구에서의 유속이 유동의 압축성 효과 및 벽면에서의 전단력 등으로 인해 노즐 형상마다 상이한 결과를 낳는다. 본 연구에서는 EDISON Simulation을 활용하여 다양한 노즐 형상에 따른 출구에서의 Mach number를 구하고, 각각의 결과로부터 경향성을 찾는다. 또, 계산 결과를 이론식을 통해 도출되는 결과와 비교한다.

• Proceeding of EDISON Challenge
• /
• 2013.04a
• /
• pp.415-420
• /
• 2013

천음속 영역에서 비행하는 에어포일 주위의 유동은 아음속 영역과는 달리 충격파(Shockwave)를 동반하고 이에 따라 복잡한 유동 현상이 발생한다. 본 연구는 천음속 영역에서 설계된 에어포일 주위의 유동에서 충격파 발생에 따른 유동변화의 특징들을 관찰하였다. 특히, 충격파에 의해서 발생하는 진동(Buffeting)과 경계층 유동 박리(Shock-induced boundary layer separation)현상에 대한 관찰과 일반적인 에어포일과 초임계 에어포일(Supercritical airfoil)간의 유동 특성의 차이점을 분석하였다. 본 연구를 위해서 EDISON CFD코드가 사용되었다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.43-46
• /
• 2004

This work is experimental study about a nozzle part in the aerodynamic igniter using only compressible gas. In study, constructions of the aerodynamic igniter using a supersonic nozzle and an aerospike nozzle have been introduced, and experimental results(mainly max. heating temperature characteristics) have been presented. Using of the supersonic nozzle leads to faster and higher temperature in same mass flow, and the aerospike nozzle works in wide variable range of pressure.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.159-162
• /
• 2007

The characteristic of air-assist spray injected into subsonic crossflow were studied experimentally. External-mixing air assist injector of Orifice nozzle with L/d of 3 were tested with various air-liquid ratio. Shadowgraph photography was performed for spray visualization and trajectory of spray measurements. The detailed spray structure was characterized in terms of SMD, velocity, and volume flux, using PDPA. Experimental results indicate that penetration length was increased and spray distribution was accelerated by increasing air-liquid ratio.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.6 no.1
• /
• pp.63-70
• /
• 2002

Computational modeling and simulation can provide an effective predictive capability for the major features of the supersonic microjets. In the present study, computations using the axisymmetic, compressible, Navier-Stokes equations are applied to understand the supersonic microjet flow physics. The pressure ratio of the microjets is changed between 0.2 and 1.25 to obtain both the under- and over-expanded flows at the exit of the micronozzle. and Reynolds number Re is changed between 600 to 40000. For both laminar and turbulent microjet flows, sonic and supersonic microjets are simulated and compared with some experimental results available. Based on computational results, two microjets are discussed in terms of total pressure, jet decay and supersonic core length.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.5
• /
• pp.70-78
• /
• 2014

A numerical study has been conducted to investigate flow and heat transfer characteristics of supersonic second throat exhaust diffusers for high altitude simulation. By changing pressure and configuration, flow and cooling characteristics of the diffuser have been studied. At the normal operation of the diffuser, there were high temperature regions over 3,000 K without cooling, especially near wall and in subsonic diffuser part. If the cooling system of the diffuser is added, flow velocity is increased due to the cooled wall temperature.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.4
• /
• pp.321-328
• /
• 2014

The performance characteristics of a subscale diffuser under non-reacting conditions for high-altitude simulation were numerically investigated with respect to different lengths of the secondary throat diffuser. The ratio of the length of the diffuser entrance to the nozzle exit diameter was set to 0, 50, and 100%. In addition, flow characteristics were studied for a range of length-to-diameter ratios of the secondary throat diffuser. An insufficient diffuser entrance length caused contraction of the plume immediately after the nozzle exit. When the length-to-diameter ratio was less than 8, a strong Mach disk was formed inside the diffuser, resulting in a sharp increase in pressure. In addition, flow characteristics in the diverging part of the diffuser were investigated for a range of diverging part lengths. A short diverging part may lead to abrupt pressure recovery, resulting in the possible application of mechanical load to the diffuser.

• The Journal of the Acoustical Society of Korea
• /
• v.39 no.6
• /
• pp.576-584
• /
• 2020

In order to obtain basic information for using polyvinyl alcohol (PVA) gel as a tissue mimicking phantom for temperature visualization, the temperature change characteristics due to the focused ultrasound were examined for different concentration of PVA. To obtain the basic acoustic characteristics, the speed of sound, the attenuation coefficient, and the density depending on the PVA concentration were measured, and the thermodynamic characteristics, such as thermal conductivity and heat capacity, were measured. The range of temperature rising in the vicinity of the focal point due to the focused ultrasound was observed using a thermochromic film that changes color at 30 degree or more, and the discolored area was obtained by image processing of the recorded image. As the concentration of PVA increases in the given range of 2 wt% ~ 16 wt%, the area that rises above 30 degree inside the gel increases linearly. It is confirmed that the discolored area increases as the power applied to the focused ultrasonic transducer increases. These results showed good agreement with the simulation results using the finite element method.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.2
• /
• pp.119-125
• /
• 2020

A high Reynolds number transonic wind tunnel has been built in 2018 at Agency for Defense Development(ADD). The tunnel has a closed circuit with a 1.5m×1.5m test section and is injection driven from a 140bar air supply system. The Mach number range is 0.3-1.2 with a conventional contracting nozzle and 1.4 with a convergent-divergent contraction. The stagnation pressure range is 100-550kPa at the lowest Mach number. An AGARD-B standard model is tested in the transonic wind tunnel to obtain 6-DOF aerodynamic coefficients. The results are compared with those obtained from ADD trisonic wind tunnel and others. We verify that the transonic wind tunnel become available to develop an aircraft from the testing results.