• Journal of Korea Port Economic Association
• /
• v.22 no.4
• /
• pp.1-17
• /
• 2006

In the Bill of Lading of The Irbenskiy Proliv is not subject to the Hague-Visby Rules in accordance with paragraphs (A) and/or (E) of cl.1 or to the Hague Rules in accordance with paragraphs (B) and/or (D) of cl.1. The Irbenskiy Proliv is very rare case that is effective to exempt the carrier as literal words of Bill of Lading. The action concerns cargoes of perishable goods shipped from Brazil to Japan, under Bills of Lading each of which contained an extensive carrier's exemption clause. A preliminary issue was ordered to be determined on the question whether c1.4 is effective to exempt the ralliers from any potential liability for the claims in this case. The court held that there is no reason to reject c1.4 as part of each of the contracts contained in or evidenced by the bills of lading; and it protects the carrier where damage to the goods shipped results from such causes. It is therefore effective to exempt the carriers from any potential liability for those claims.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.9
• /
• pp.1991-1998
• /
• 2015

This paper presents the antenna factor characteristics of a calculable dipole antenna with a hybrid balun, installed above ground plane vertically and horizontally, using Method of Moments (MoM). An expression for the antenna factor is formulated using the concept of power mismatch loss. The input impedance and effective length of the antenna, which are in the formula of the antenna factor, are calculated using the MoM. The results show that the antenna factors above a ground plane are agreed with the free space antenna factors within ± 0.14 dB. The horizontal antenna factors are varied more by 0.2 dB than the vertical antenna factors.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.7
• /
• pp.3169-3175
• /
• 2011

This paper describes the design of size-reduced directional coupler using the artificial dielectric substrate and its increased effective permittivity. Directional couplers are widely used in measuring RF power indirectly and coupling signal power. Artificial dielectric substrates have higher effective dielectric constant than standard dielectric substrate due to the lots of metalized via-holes, and the increased effective permittivity results in size-reduction of circuits. As a design example, 15dB directional couplers are designed on the standard substrate and artificial dielectric substrate and their size are compared. The size of the directional coupler using the artificial dielectric substrate is only 1/3 of that designed using the standard substrate, while the performances are preserved. In addition, the measured performances of the size-reduced coupler are well agreed with the simulated ones. The measured coupling coefficient, matching, and insertion loss at 2GHz are -14.62dB, -24.1dB, and -0.38dB, respectively.

• Journal of the Institute of Convergence Signal Processing
• /
• v.14 no.2
• /
• pp.136-146
• /
• 2013

In this paper, the residual delay compensation algorithm is proposed for FX-type KJJVC. In case of initial version as that design algorithm of KJJVC, the integer calculation and the cos/sin table for the phase compensation coefficient were introduced in order to speed up of calculation. The mismatch between data timing and residual delay phase and also between bit-jump and residual delay phase were found and fixed. In final design of KJJVC residual delay compensation algorithm, the initialization problem on the rotation memory of residual delay compensation was found when the residual delay compensated value was applied to FFT-segment, and this problem is also fixed by modifying the FPGA code. Using the proposed residual delay compensation algorithm, the band shape of cross power spectrum becomes flat, which means there is no significant loss over the whole bandwidth. To verify the effectiveness of proposed residual delay compensation algorithm, we conducted the correlation experiments for real observation data using the simulator and KJJVC. We confirmed that the designed residual delay compensation algorithm is well applied in KJJVC, and the signal to noise ratio increases by about 8%.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.5 s.335
• /
• pp.31-38
• /
• 2005

The architecture and the implementation details of a UTMI(USB2.0 Transceiver Macrocell Interface) compatible USB2.0 transceiver chip were presented. To confirm the validation of the incoming data in noisy channel environment, a squelch state detector and a current mode Schmitt-trigger circuit were proposed. A current mode output driver to transmit 480Mbps data on the USB cable was designed and an on-die termination(ODT) which is controlled by a replica bias circuit was presented. In the USB system using plesiochronous clocking, to compensate for the frequency difference between a transmitter and a receiver, a synchronizer using clock data recovery circuit and FIFO was designed. The USB cable was modeled as the lossy transmission line model(W model) for circuit simulation by using a network analyzer measurements. The USB2.0 PHY chip was implemented by using 0.25um CMOS process and test results were presented. The core area excluding the IO pads was $0.91{\times}1.82mm^2$. The power consumptions at the supply voltage of 2.5V were 245mW and 150mW for high-speed and full-speed operations, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.153-162
• /
• 2017

Weapon systems have been developed with high technology electronic equipment due to technology growth. In addition, the capital, operational and maintenance costs of weapon systems have all increased. However, cost of operation and maintenance for weapon systems has been decreased relatively compared to the increased capital cost of weapon systems. Therefore, the defense industry needs to research the life cycle cost of weapon systems that have high operational and maintenance costs. This paper focuses on maintenance equipment for the operation and maintenance of weapon systems. Recently, it seems that the weapon systems that have periodic calibration with maintenance equipment are valid. The equipment requires periodic calibration by the manufacturer to check its own validation. Basically, customers demand high reliability devices from foreign companies that have qualified in the global market. Therefore, the tools need to be calibrated overseas. In other words, weapon systems are not available when the equipment has to be calibrated overseas because the systems require validation with valid maintenance equipment. A purpose of this paper is to compare the loss costs that arise from the calibration of the equipment overseas and the purchasing cost of the tools. Finally, the research shows the number of equipment that customers need to minimize the cost. This research will help to improve the efficiency of operation of weapon systems and solve the problems associated with the need for maintenance overseas.