• Journal of the Korean Geotechnical Society
• /
• v.33 no.4
• /
• pp.47-56
• /
• 2017

Aseismic designs of pile-supported wharves are commonly performed utilizing simplified dynamic analyses, such as multi-mode spectral analyses. Simplified analyses can be useful for evaluating the limit state of structures. However, several pile-supported wharves, that have been damaged during past earthquakes, have shown that soil deformation and soil-pile dynamic interaction significantly affect the entire behavior of structures. Such behavior can be captured by performing nonlinear effective stress analyses, which can properly consider the dynamic interactions among the soil-pile-structure. The present study attempts to investigate the earthquake performance of a pile-supported wharf utilizing a three-dimensional numerical method. The damaged pile-supported wharf at the Kobe Port during the Hyogo-ken Nambu earthquake (1995) is selected to verify the applicability of the numerical modeling. Analysis results showed a suitable agreement with the observations on the damaged wharf, and the significant effect of excess pore pressure development and pile-soil dynamic interaction on the seismic performance of the wharf.

• Journal of the Korean Geosynthetics Society
• /
• v.19 no.3
• /
• pp.9-21
• /
• 2020

In this study, the design method of the combined sheet pile was considered in the coastal landfill where sandy and clayey soils are mixed, and the behavior in excavation was analyzed. It was confirmed from the elasto-plastic analysis that the predicted behavior of the temporary facilities of earth retaining differs according to the type of the combined sheet pile method (Built up, Interlocking, Welding) and the analysis method (soldier pile method, continuous wall method). In the case of sheet pile member force, the results of the continuous wall analysis method predicted the most conservative results. When the stress ratio (calculation/allowance) of each member was analyzed based on the maximum member force of the combined sheet pile method, the maximum value was obtained for bending moment in the side pile and combined stress in the case of the strut. As a result of finite element analysis, the member force of the side pile was the largest in the short-term effective stress analysis condition, while the compressive force of the strut was large in the consolidation analysis. When comparing the results of the elasto-plastic analysis and the finite element analysis, the shear force of the side pile and the axial force of the strut were greatly evaluated in the elasto-plastic analysis, and the bending moment of the side pile was the largest in the short-term effective stress condition of the finite element analysis. In addition, the displacement of the side pile was predicted to be greater in the finite element analysis than in the elasto-plastic analysis.

• Land and Housing Review
• /
• v.13 no.1
• /
• pp.141-150
• /
• 2022

Responding to the increasing demand for research on seismic resistance of structures triggered by a large-scale earthquake in Korea, the Ministry of the Interior and Safety revised the typical application of the existing seismic design standards with the national seismic performance target enhanced. Therefore, in this paper, the dam body of the aged Test-Bed and the penstock with fluid were modeled by the three-dimensional finite element method by introducing several variables. The current seismic design standard law confirmed the safety of the dam structure and penstock against seismic waves. As a result of the 3D finite element analysis, the stress change due to the water impact of the penstock was minimal, and it was confirmed that the effect of the hydraulic pressure was more significant than the water impact in the earthquake situation. When the hydrostatic pressure is in the form of SPH, it was analyzed that the motion of the fluid and the location of stress caused by the earthquake can be effectively represented, and it will be easier to analyze the weak part. As a result of the analysis, which considers penstock's corrosion, the degree of stress dispersion gets smaller because the penstock is embedded in the body. The stress result is minimal, less than 1% of the yield stress of the steel. In addition, although there is a possibility of micro-tensile cracks occurring in the inlet of the dam, it has not been shown to have a significant effect on the stress increa.

• Journal of the Society of Naval Architects of Korea
• /
• v.38 no.3
• /
• pp.74-83
• /
• 2001

After the concept of fracture mechanics was applied to fatigue crack propagation by Paris. Paris' law is widely used to predict fatigue crack growth behavior. Since Elber proposed the effective stress intensity factor(SIF) and showed a good agreement with experimental results using the proposed SIF, emphasis in crack propagation studies has been placed on measuring the effective stress range ratio. This paper proposes a numerical model to simulate the crack closure and propagation behaviour under various loading spectrum. The validity of the proposed model is checked by comparing with the Toyosada numerical solutions on the crack propagation behaviour. Important insights developed are summarized.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.23 no.4
• /
• pp.343-351
• /
• 2010

Bending and axial compressive stresses are distributed across the whole upper flange of a box girder bridge which has the span-to-depth ratio (B/L) of below 0.5, according to Korea Bridge Design Specifications (Minister of Land, Transport and Maritime Affairs, 2005). Shear lag phenomenon, however, can take place in the construction phase of cable-stayed bridge, in which stresses combining bending moment due to dead weight and cable vertical compression are induced. This study aims to analyze the effective width of flange over which composite stresses are given, which should be calculated during the construction phase of stiffening girder of single plane cable-stayed box girder bridge. The study results indicate that the full width of stiffening girder can be regarded as the effective flange width when the span-to-depth ratio for the deck is below 0.38. In other words, the area, where shear lag is taken into consideration, is larger than the width of box girder in single plane cable-stayed box girder bridges. Therefore, the current practice of considering the full width as the effective flange width regardless of changes of the span-to-depth ratio during the construction stage can produce an unsafe bridge. If the effective flange width is determined according to the single span structural system in the early stage of construction when the span-to depth ratio for the deck is high and composite stresses of every part expect each end of the bridge are calculated, it can result in a safe structural design. Since the span-to-depth ratio gradually decreases, however, it is appropriate to determine the effective width of flange on the basis of the full width and the cantilever structural system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.3
• /
• pp.323-331
• /
• 2010

In this study, we propose a 3D finite element (FE) model for the residual stress under oblique shot peening. Using the FE model for an oblique impact, we examine the effects of factors on the residual stress such as the Rayleigh damping in the material, dynamic friction, and the rate dependency of the material and systematically integrate the effects. The plastic deformation of the shot is also emphasized. Then, the FE model is used to study oblique multi-impacts. The results obtained using the FE model are compared with experimental x-ray diffraction (XRD) results; in contrast to the rigid and elastic shots, plastic shots are found to produce residual stresses similar to that shown in the XRD results. Thus, the 3D FE models with integrated factors and plastically deformable shots are validated. The proposed model will serve as a basis for the 3D FE model for multi-impacts with different impact angles to simulate the actual phenomenon of shot peening.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.11 no.1
• /
• pp.35-44
• /
• 1974

열박음(shrink fitting)으로 인(因)한 동심형(同心形) 구멍을 가진 복합(複合)실린더의 과도적(過渡的) 온도분포(溫度分布), 열응력(熱應力) 및 열변형도(熱變形度)를 이론해석(理論解析)하였다. 온도분포해석(溫度分布解析)에서 외부(外部) 실린더는 균일온도(均一溫度)로 가열(加熱)되어, 실온(室溫)의 내부(內部) 실린더와 접촉면(接觸面)에서 일어나는 열전도(熱傳導)에 의(依)하여 냉각(冷却)되고, 외부(外部) 표면(表面)은 대기중(大氣中)에 노출(露出)된 상태(狀態)로 취급(取扱)하였다. 열응력(熱應力)은 평면변형도조건(平面變形度條件)을 만족(滿足)하는 것으로 생각하였으며, 물성(物性)은 온도(溫度)에 무관(無關)한 상수(常數)로 취급(取扱)하였다. 온도분포(溫度分布)는 열전도문제(熱傳導問題)만을 고려(考慮)함으로서도 유효(有效)한 해(解)를 얻을 수 있으며 열응력(熱應力)은 접촉면(接觸面)에서부터 형성(形成)되며, 반경방향응력(半徑方向應力)은 시간(時間)이 경과(經過)함에 따라 압축응력(壓縮應力)이 증가(增加)하여 접촉면(接觸面)에서 최대치(最大値)를 갖고, 원주방향응력(圓周方向應力)은 접촉면(接觸面)에서 초기(初期)부터 거의 최종상태(最終狀態)와 같은 크기를 갖음을 알 수 있다. 균일온도분포(均一溫度分布)가 이루어지면 열응력(熱應力)의 형성(形成)은 완료(完了)되게 되며, 이때의 열응력(熱應力)의 크기와 분포경향(分布傾向)은 평면응력조건(平面應力條件)을 사용(使用)하였다는 사실(事實)을 고려(考慮)하면 $Lam\acute{e}$의 이론해(理論解)와 일치(一致)함을 알 수 있었다.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1989.10a
• /
• pp.1.1-10
• /
• 1989

본 연구에서는 유효응력 개념에 기초를 둔 응력-변형을 관계식을 이용하여 비배수 지하굴착 거등을 모댈하기 위한 수치해석적 방법이 개발된다. 비배수 조건 시 적용되는 체적불변형 조건은 조건방정식(Penalty formulation)의 혁태로 공극수압 변수를 이용하여 주어지며 결과되는 유한요소 방정식에 상닻히 른 물외 체적변형 개수를 부여함으로서 이루어진다. 이러한 형태와 조건식은 지하굴착 과정에서 발생되는 비배수 공극수압의 계산을 가능케 한다. 체적불변형 조건 부여 시 발생되는 mesh locking은 그 결과에 상당한 영향을 미치므로 이러한 mesh locking 문제는 T-방법에 근거를 둔 salective 적분방법월 적용함으로서 해결될 수 있다. 또한 흙의 거등을 모델하기 위하여 사용 된 Cam-Clay모텔과 Drucker-prager모텔에 새로운 implicit 웅력적분 방법을 적용함으로서 효율적인 방법으로 비선형거동을 해석할 수 있다. 개발된 지하 굴착 해석방법의 적용성을 검증하기 위하여 실재 현장에서 측정된 지하굴착 거동을 예제로 이용하였다.

• Journal of the Korea Concrete Institute
• /
• v.28 no.6
• /
• pp.655-663
• /
• 2016

The present study shows the moment-average curvature relationship and effective inertia moment of RC beams obtained from the nonlinear analysis based on the parabola-rectangular stress-strain curve defined in EC-2 code. The variables examined are concrete strength and steel ratio, and moment-average curvature relationship and effective inertia moment obtained are compared with those of the current KCI provisions. As the results of the comparison, the followings could be said: Since the KCI provisions(the Branson method) were originally derived based on the experimental data ranged from 2.2 to 4 of $M/M_{cr}$ and 1.3 to 3.5 of $I_{ut}/I_{cr}$, thereby within these ranges the inertia moments obtained from the nonlinear analysis are closely agreed with those predicted by the Branson method. However, beyond those range the remarkable difference could be found between the two results. In particular, for beams having low steel ratio the inertia moment resulted from the nonlinear analysis are significantly smaller than those obtained from the KCI(Branson) method. This result may imply that the deflection of lightly reinforced members, such as slabs in buildings, becomes much larger than those calculated according to the current design provisions.

• Proceedings of the KWS Conference
• /
• 1999.05a
• /
• pp.237-240
• /
• 1999

In this study, residual stresses of the weldment were calculated by finite element analysis(FEA) and experiment. And, the crack closure behaviour and fatigue crack growth characteristics in field of residual stress of A106 Gr B steel pipe weldment were investigated under various stress ratio. Obtained results are as follows. I) $K_{op}$ was independent of $K_{max}$, and load ratio in fatigue crack growth. 2) In variation of load ratio, the scatter band of crack growth curve was reduced by half considering crack closure. and 3) Neglecting crack closure behaviour, actual fatigue crack growth rate can be underestimated' and Actual fatigue crack growth rate can be overestimated by $K_{res}$, in tensile residual stress field.