• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.113.2-113.2
• /
• 2011

Sn-Ag계 합금은 대표적인 무연 솔더 조성으로 전자제품의 실장 및 접합에 적용되어 왔으며, 태양전지 분야에서도 모듈의 전극과 bus바로 사용되는 등 다양한 분야에서 사용되고 있다. 그러나 최근 Ag 가격의 급격한 상승과 솔더 접합부의 신뢰성을 보다 향상시키고자 Ag의 함량을 줄이고 다원계 합금 조성의 무연 솔더 연구가 활발히 진행되고 있다. 본 실험에서는 기존의 연구 결과를 바탕으로 Sn-1.0Ag-0.5Cu-0.4In 4원계 무연솔더 조성에 Bi를 첨가하여 최적의 융점과 용융구간을 가지는 5원계 Sn-Ag-Cu-In-Bi 계 솔더 합금을 설계하였다. 이 설계된 합금은 기존의 유연 솔더인 Sn-Pb와 대표적인 무연 솔더인 Sn-3.5Ag와 각각의 특성을 비교 분석하였다. 젖음성을 평가하기 위하여 wetting balance tester를 이용하여 실험을 행하였고 Differential Scanning Calorimetry(DSC)를 분석하여 젖음 정도와 조성 분석 및 고상점과 액상점 등의 녹음 거동을 확인하였다. 또한 각각의 조성별 전단응력에 따른 파괴 거동을 분석하였다.

• Journal of Applied Reliability
• /
• v.5 no.3
• /
• pp.327-342
• /
• 2005

전자 패키지가 열을 받을 때 회로기판과 칩의 열팽창계수 차이에 의해 발생되는 응력은 솔더 조인트의 파손에 영향을 미친다. 본 연구에서는 이 영향을 정량적으로 규명하기 위하여 열충격시험기를 이용해 얻어진 솔더 조인트의 전기저항 변화와 수명과의 상관관계를 규명하였고, BGA솔더 조인트의 수명을 정량적으로 도출하였다. 또한 Sn-3.5Ag-0.5Cu 무연 솔더와 63Sn-37Pb 유연 솔더를 위의 실험에 동시에 적용시켜 건전성을 FORM(first-order reliability method)과 Weibull Function Model을 이용해 비교하였다.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.3
• /
• pp.37-44
• /
• 2013

It is well known that thermal deformation of electronic packages with Pb-Sn solder and with lead-free solder is significantly affected by material properties consisting the package, as well as those of the solder itself. In this paper, the method for determining coefficient of thermal expansion(CTE) of new material is established by using temperature characteristic of strain gages, and the CTE of molding compound are obtained experimentally. The temperature-dependent CTE of molding compound for Pb-Sn solder and that for lead-free solder are obtained by using strain measurements with well known steel specimen and aluminium specimen as reference specimens, and the CTE's are also measured non-contactly by using moire interferometry. Those results are compared, and the agreement between the two types of strain gage experiment and the moire experiment show the strain gage method used in this paper to be reliable. In the case of the molding compound for Pb-Sn solder, the CTE is measured as approximately $15.8ppm/^{\circ}C$ regardless of the temperature. In the case for the lead-free solder, the CTE is measured as of approximately $9.9ppm/^{\circ}C$ below the temperature of $100^{\circ}C$, and then the CTE is increased sharply depending on the temperature, and reaches to $15.0ppm/^{\circ}C$ at $130^{\circ}C$.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.3
• /
• pp.13-19
• /
• 2018

The soldering property of Pb-containing solder(Sn-Pb) and Pb-free solders(Sn-3.0Ag-0.5Cu and Sn-1.0Ag-0.7Cu-1.6Bi-0.2In) for solar combiner box module was compared. The solar combiner box module was composed of voltage and current detecting modules, diode modules, and other modules. In this study, solder paste printability, printing shape inspection, solder joint property, X-ray inspection, and shear force measurements were conducted. For optimization of Pb-free soldering process, step 1 and 2 were divided. In the step 1 process, the printability of Pb-containing and Pb-free solder alloys were estimated by using printing inspector. Then, the relationship between void percentages and shear force has been estimated. Overall, the property of Pb-containing solder was better than two Pb-free solders. In the step 2 process, the property of reflow soldering for the Pb-free solders was evaluated with different reflow peak temperatures. As the peak temperature of the reflow process gradually increased, the void percentage decreased by 2 to 4%, but the shear force did not significantly depend on the reflow peak temperature by a deviation of about 0.5 kgf. Among different surface finishes on PCB, ENIG surface finish was better than OSP and Pb-free solder surface finishes in terms of shear force. In the thermal shock reliability test of the solar combiner box module with a Pb-free solder and OSP surface finish, the change rate of electrical property of the module was almost unchanged within a 0.3% range and the module had a relatively good electrical property after 500 thermal shock cycles.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.12
• /
• pp.1856-1863
• /
• 2004

In the last 50 years, lead-contained solder materials have been the most popular interconnect materials used in the electronics industry. Recently, lead-free solders are about to replace lead-contained solders for preventing environmental pollutions. However, the reliability of lead-free solders is not yet satisfactory. Several researchers reported that lead-contained solders have a good fatigue property. The others published that the lead-free solders have a longer thermal fatigue life. In this paper, the reason for the contradictory results published on the estimation of fatigue life of lead-free solder is investigated. In the present study, fatigue behavior of 63Sn37Pb, and two types of lead-free solder joints were compared using pseudo-power cycling testing method, which provides more realistic load cycling than chamber cycling method does. Pseudo-power cycling test was performed in various temperature ranges to evaluating the shear strain effect. A nonlinear finite element model was used to simulate the thermally induced visco-plastic deformation of solder ball joint in BGA packages. It was found that lead-free solder joints have a good fatigue property in the small temperature range condition. That condition induce small strain amplitude. However in the large temperature range condition, lead-contained solder joints have a longer fatigue life.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.1
• /
• pp.322-328
• /
• 2012

This paper deals with a digital Desoldering system for removing lead-free solder. We proposed a Desoldering system that is to cope with the changed work environment of the solder materials changing from lead solder to lead-free solder, we can be quickly stable to the set temperature, and continuous operation is possible. Proposed system consists of a Desoldering station and a Desoldering gun. For the PID temperature control, we designed the 8bit MCU peripheral circuit. We had a few experiments to confirm the performance of the proposed system, and compared with the specification of same kind of imports. As a result, proposed system than the imported products showed good performance as follows: the time to reach operating temperature is 11 seconds faster, ripple temperature variation is $1.5^{\circ}C$ lower, temperature recovery rate is about $0.14^{\circ}C$/sec faster.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.2
• /
• pp.25-30
• /
• 2018

Sn-Pb solder has been used in automotive electronics for decades. However, recently, due to the environmental and health concerns, some international environmental organizations such as the end-of-life vehicle (ELV) enacted legislation banning of the Pb usage in automotive electronics. For this reason, many studies to develop and promote Pb-free soldering have been significantly reported. Meanwhile, because of flexibility and lightweight, flexible printed circuit boards (FPCBs) have been increasingly used in automotive electronics for lightweight to improve fuel efficiency and space utilization. Although the properties of lead-free solders for automotive electronics have been widely studied, there is a lack of research on the reliability performance of the lead-free solder joint on FPCB under user conditions. This study reported the properties of solder joints between Pb-free solders such as Sn3.0Ag0.5Cu, Sn0.7Cu and Sn0.5Cu0.01Al (Si), and various FPCBs finished with organic solderability preservative (OSP) and electroless nickel immersion gold (ENIG). To evaluate on joint properties and reliabilities with different solder compositions and surface-finishing materials, pull strength test, thermal shock test, and bending cycle test were performed and analyzed. After the bending cycle test of solder joint on OSP-finishing, the fractures were occurred in solder and the lifetime of Sn3.0Ag0.5Cu solder joint was the longest.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.250-255
• /
• 2008

This study utilized a high speed lap-shear test to evaluate the mechanical behavior of Sn-37Pb/Cu and Sn-37Pb/Electroless Nickel immersion Gold under bump metallization solder joints under high speed loading and hence the drop reliability. The samples were aged for 120 h at different temperatures ($120^{\circ}C,\;150^{\circ}C,\;170^{\circ}C$) and afterward tested at different displacement rates (0.01 mm/s to 500 mm/s) to examine the effects of aging on the drop life reliability. The combination of the stress-strain graphs captured from the shear tests and identifying a fracture mode dominant in the samples for different strain rates leads us to conclude that the drop reliability of solder joints degrades as the aging temperature increases, possibly due to the role of the IMC layer. This study successfully demonstrates that the analysis based on a high speed lap-shear test could be critically used to evaluate the drop reliability of solder joints.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2005.11a
• /
• pp.515-518
• /
• 2005

플립칩과 같은 정밀한 전자부품을 일반적인 표면실장방법에 의해 고속으로 장착 시킬 경우에는 칩의 표면이 PCB 실장면에 닿는 순간 접촉력(Contact Force)이 크게 발생한다. 과도한 접촉력에 의해 솔더 볼의 표면에 크랙이 가거나 솔더 볼이 변형되어 좁은 피치 내에서 인접해 있는 솔더 볼이 서로 붙는다든지, 또한 리드가 손상된다든지 하는 등과 같은 현상이 발생하여 표면 실장 불량의 원인이 될 가능성이 높아진다. 또한, 유연한 재질로 구성된 PCB 실장면에 과도한 힘을 가할 시에는 실장면의 국부적인 탄성변형이 발생하여 칩의 장착위치가 변경되어 정확한 위치에의 장착이 어렵게 된다. 따라서 CSP 나 플립 칩과 같은 고정도 칩을 고속으로 정확한 위치에 실장하기 위해서는 칩을 장착할 때 플립칩과 실장면의 자세를 평형상태로 제어할 필요가 있으며, 특히 발생하는 충격을 감소시키기 위한 충격 제어와 충돌 후 일정한 접촉력 유지를 할 수 있는 힘 제어가 필수적임을 알 수 있다. 따라서 본 논문에서는 상기와 같은 자세제어 및 힘제어를 요구하는 플립 칩 장착을 위한 엑츄에이터와 거리/힘 센서 시스템을 개발하였다. 제안된 시스템의 효율성을 입증하기 위해 다양한 환경에서 성능시험을 수행하였으며, 그 결과 제안된 시스템의 만족할 만한 실험결과를 보여주었다.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.2
• /
• pp.121-127
• /
• 2022

Micro-LED is a light-emitting diode smaller than 100 ㎛ in size. It attracts much attention due to its superior performance, such as resolution, brightness, etc., and is considered for various applications like flexible display and VR/AR. Micro-LED display requires a mass transfer process to move micro-LED chips from a LED wafer to a target substrate. In this study, we proposed a vacuum chuck method as a mass transfer technique. The vacuum chuck was fabricated with MEMS technology and PDMS micro-mold process. The spin-coating approach using a dam structure successfully controlled the PDMS mold's thickness. The vacuum test using solder balls instead of micro-LED confirmed the vacuum chuck method as a mass transfer technique.