• Polymer(Korea)
• /
• v.31 no.6
• /
• pp.479-484
• /
• 2007

In this study, the hybrid ion exchange fibers (HIEF) were prepared by using web spraying muthod with hot melt adhesive. Characteristics of HIEF and their adsorption properties for ammonia gas were investigated. The ion exchange capacity (IEC) of HIEF was increased with increasing the resin contents and their values were higher than those of pure resin and ion exchange fabrics. The removal efficiency for ammonia gas increased with an increase in packing density of hybrid ion exchange fabrics in the column. The adsorption breakthrough time was 270 min, which was slower than those of the resin and fibers. The maximum value of adsorption for ammonia gas was 94%. The breakthrough time was also increased with increasing the concentration and flow rate of ammonia gas. The reaction constant(k) for ammonia gas was increased with increasing the concentration and flow rate of the gas, while it was decreased an the mass was increased.

• Membrane Journal
• /
• v.29 no.6
• /
• pp.314-322
• /
• 2019

A worsened drought in Chungnam province of Korea due to climate change and increasing water demand at Daesan industrial complex have motivated the 100,000 ㎥/d seawater desalination project. In this study, therefore, the comprehensive analysis of parameters affecting the reverse osmosis (RO) performance was conducted. Under the various conditions of feedwater salinity and temperature in Daesan, energy consumption was calculated as 2.39 ± 0.13 kWh/㎥. The decrease in membrane flux and recovery rate positively impacted annual operation cost. The average total dissolved solids (TDS) of the permeate and energy consumption with highly permeable membrane according to the membrane manufacturer were 3.84 mg/L and 2.22 ± 0.13 kWh/㎥, respectively. In addition, energy saving up to 0.29 kWh/㎥ or cost reduction of membrane module up to 15.6% is expected by changing the RO configuration from full two pass to partial or split partial two pass.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.539-539
• /
• 2008

본 논문에서는 투명전도박막의 균일한 표면특성을 확보하기 위해 광역평탄화 공정을 적용하여 투명전도 박막의 표면 거칠기를 연구하였으며 슬러리의 종류에 따른 박막의 연마특성을 연구하였다. 본 실험에서 사용된 ITO 박막은 RF Sputtering에 의해 제작되었고 하부 기판은 석영 Glass가 사용되었다. 광역평탄화를 위한 CMP 공정은 고분자 물질계열의 패드위에 슬러리입자를 공급하고 웨이퍼 캐리어에 하중을 가하며 웨이퍼의 표면을 연마하는 방법으로 가공물을 탄성패드에 누르면서 상대 운동시켜 가공물과 친화력이 우수한 부식액으로 화학적 제거를 함과 동시에 초미립자로 기계적 제거를 하는 것이다. ITO 박막의 평탄화를 위한 공정조건은 Polisher pressure 300 g/$cm^2$, 슬러리 유속 80 ml/min, 플레이튼속도 60 rpm으로 하였다. 위의 조건에 따라 공정을 진행 후 연마특성을 측정하였으며 이때 사용된 슬러리는 산화막에 사용되는 실리카슬러리와 금속연마용 슬러리인 EPL을 사용하였다. 연마율은 실리카 슬러리가 EPL슬러리에 비해 높음을 확인 하였다. CMP 공정에 의해 평탄화를 수행 할 경우 실리카슬러리와 EPL슬러리 모두 CMP전에 비해 돌출된 힐록들이 감소되었음을 알 수 있었다. 비균일도 특성은 모든 슬러리가 양호한 특성을 나타내었다. 평탄화된 박막의 표면과 거칠기 특성은 AFM(XE-200, PSIA Company) 을 이용하여 분석을 하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.6 no.2
• /
• pp.37-44
• /
• 2002

A theoretical study of spray and combustion characteristics due to coaxial twin-fluid injection is conducted to investigate the effects of liquid jet property, droplet size, contact length and liquid jet velocity. Model is properly validated with measurements and shows good agreement. Prediction of jet contact length, droplet size, liquid jet velocity reflects genuine features of coaxial injection in physical and practical aspects. Both the jet contact length and tile droplet size are reduced in a linear manner with an increase of injector diameter. Cross sectional area of liquid intact core is reduced with augmented jet splitting rate, thus the jet is accelerated to maintain the mass continuity and with an assistant of momentum diffusion by burnt gas.

• Korean Journal of Food Science and Technology
• /
• v.11 no.1
• /
• pp.8-12
• /
• 1979

A cylindrical solar energy focusing collector constructed using aluminum-laminated film plastered on the acrylic plate and examined its performances under the Korean local weather conditions. The reflector surface of this collector· evidenced the reflectivity of 66.1%,which was satisfactory value that could be applicable to the solar collector for its low price and at·availability. Collector efficiency measured at the heat exchanger fluid in absorber-copper pipe black colored was 73% and the resulting natural convection of the heat transfer media (water) was recorded up to 2.82 cm/sec. The overall efficiency of the solar heater in operation was 28.6% and it was correlated with the solar energy input and the temperature elevation difference gained.

• Fire Science and Engineering
• /
• v.33 no.2
• /
• pp.9-19
• /
• 2019

Experiments on the combustion characteristics of untreated wood specimens and those treated with four types of silicone compounds were carried out using a cone calorimeter according to the ISO 5660-1 standard. 3-Aminopropyltrimethoxysilane (APTMS), 3-(2-aminoethylamino) propylmethyldimethoxysilane (AEAPMDMS), and 3-(2-aminoethylamino) propyltrimethoxysilane (AEAPTMS) were used as the silane compounds. The flame retardants were synthesized with sodium silicate and amino silane compounds. The measured time to ignition after combustion at an external heat flux of $50kW/m^2$ was 9 s to 11 s. Time to ignition was marked with a delayed value in the 3 s to 5 s range. The peak heat release rate ($HRR_{peak}$) was reduced by 5 to 20% compared with the uncoated specimen, and AEAPMDMS showed the highest initial fire risk. The total heat release (THR) was decreased by 1 to 22%. Compared to the untreated specimen, the fire performance index (FPI) of the specimens coated with silicone sol compounds increased by 1.5 to 2.2 fold. The fire growth index (FGI) of the AEAPMDMS specimen was increased by 30% and the others were decreased by 93 to 94%. Therefore, the fire risk of wood coated with silicone compounds was improved in terms of the heat risk properties.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.5
• /
• pp.468-475
• /
• 2005

Biofilters packed with various materials have emerged as a sustainable technology for the treatment of volatile organic compounds (VOCs); however, problems including low performance and clogging are commonly encountered. Recently, a bioactive foam reactor (BFR) using surfactants has been suggested to ensure efficient and stable VOCs removal performance. This study was mainly conducted to investigate the feasibility of BFRs using toluene as a model compound. Prior to bioreactor studies, a series of bottle tests were used to select a suitable surfactant for the BFR application. Experimental results of the batch bottle tests indicated that TritonX-100 was the most appropriate one among the surfactants tested, since it showed a minimal effect on the toluene biodegradation rate while the other surfactants lowered the toluene biodegradation rate significantly. Using the selected surfactant, the BFR performance was determined by changing operating parameters including gas residence time and toluene loading. As the gas residence time increased from 0.5 minutes to 2 minutes, the toluene removal efficiency increased from approximately 50% to 80%. In addition, an increase of the toluene loading from $38\;g/m^3/hr$ to $454\;g/m^3/hr$ resulted in a decrease of toluene removal efficiency from approximately 70% to 20%. The BFR had a maximum elimination capacity of $108\;g/m^3/hr$ for toluene, which was much higher than those generally reported in the literature. The high toluene-elimination performance indicates that the BFR be a potential alternative to the conventional, packed-type biofilters. However, the limitation of toluene solubilization and foam stability at either high or low gas flow rate are still problems to be challenged.

• Journal of Soil and Groundwater Environment
• /
• v.10 no.5
• /
• pp.11-17
• /
• 2005

Characteristics of phenanthrene removal in the Electrokinetic (EK)-Fenton process were investigated in a 2-dimensional test cell in a viewpoint of the effect of gravity and electrosmotic flow (EOF). When the constant voltage of 100 V was applied to this system, the current decreased from 1,000 to 290 mA after 28 days, because soil resistance increased due to the exhaustion of ions in soil by electroosmosis and electromigration. Accumulated EOF in two cathode reservoirs was 10.3 L and the EOF rate was kept constant for 28 days. At the end of operation, the concentration of phenanthrene was observed to be very low near the anode and increased in the cathode region because hydrogen peroxide was supplied from anode to cathode region following the direction of EOP. Additionally, the concentration of phenanthrene decreased at the bottom of the test cell because the electrolyte solution containing hydrogen peroxide was largely transported toward the bottom due to a low capillary action in the soil with high porosity. Average removal efficiency of phenanthrene by EK-Fenton process was 81.4% for 28 days. In-situ EK-Fenton process would overcome the limitations of conventional remediation technologies and effectively remediate the contaminated sites.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.15 no.1
• /
• pp.30-37
• /
• 2012

This paper assessed environmental impact of tidal power plant construction in the western sea of Korea, and diagnosed problems of the related assessment. We also proposed key assessment items (scoping) and system improvement for environmental impact assessment (EIA). The establishment of a broad consensus of the appropriateness and a clear purpose for business is an important aspect of the aptness of using the waters, and the aggressive collecting of opinions of the stakeholder and institutions will have to be fulfilled. In addition, we presented the following scoping plan in order to minimize the negative effects of the marine ecosystem and the conflict between the people who work in the fishing industry which result due to the construction of the tidal power plants. (1) the change in seawater exchange rates and the aspect of erosion/sedimentation which result from the change in the velocity of running fluid, (2) the destruction of spawns/habitats of fish due to the damage of tidal flats, (3) fishery resources, impacts of fishing grounds, and the spread of suspended sediments, etc. will have to be applied to the key assessment items(scoping). In addition, every citizen will have work hard for an establishment of an active plan which achieves the harmony and balance of environmental preservation and for the policy to be applied through changing their consciousness of environmental preservation.

• Proceedings of the Korea Crystallographic Association Conference
• /
• 1999.04a
• /
• pp.1-1
• /
• 1999

부유대용융법에 의하여 불순이온의 종류와 각 이온의 주입 농도를 달리하는 Rutile 단결정을 성장하였다. 성장된 결정으로부터 제조한 박편시료를 이용하여 결정결함과 광투과도에 미치는 각 불순이온의 영향을 조사하였다. 결정성장용 주원료로 99.99%의 TiO2를 사용하고, 불순이온 주입을 위한 원료로서 99.99%의 Al2O3, H3BO3, Ga2O3, Sc2O3, V2O5, Fe2O3, ZrO2, Er2O3, Cr2O3를 각각 사용하였다. 불순이온의 종류에 따르는 영향을 조사하기 위하여 TiO2 99.8 atomic%-불순이온 0.2atomic%의 조성이 되도록 각 이온별로 원료를 정밀하게 평량하고 균일 혼합하였다. 불순 이온의 첨가량에 따르는 영향을 조사하기 위하여 Al2O3는 각각 pure, 0.2, 0.4, 0.6 atomic%를, Cr2O3는 pure, 0.003, 0.05, 0.2 atomic%를 각각 치환하여 원료를 조합하였다. 균일 혼합된 원료를 직경 8mm의 고무 튜브에 넣고 CIP(Cold Isostatic Press0에서 2000kg/$\textrm{cm}^2$의 압력으로 성형한 후 150$0^{\circ}C$에서 1시간 소결함으로서 결정성장용 다결정 원료를 합성하였다. 합성된 다결정을 double ellipsoidal mirror 내에 설치하고,halogen lamp로 가열하여 원료의 한쪽 끝을 용융한 다음, 20rpm의 회전속도, 3-5mm/hr의 성장속도로 하는 유속 1$\ell$/min의 O2 분위기속에서 부유대용융법에 의하여 결정을 성장하였다. 성장된 결정을 성장축에 수직한 방향으로 각각 절단, 연삭, 연마한 박편을 이용하여 편광하에서 low-angle grain boundaries 및 기타의 결정결함을 관찰하였으며, 0.3$\mu\textrm{m}$~0.8$\mu\textrm{m}$ 범위 및 0.6$\mu\textrm{m}$~3.4$\mu\textrm{m}$ 범위에서의 투과 및 흡수 스펙트럼을 측정하였다. 결정 성장 결과 B3+, Er3+, Cr3+ 이온은 Ti4+ 이온과 이온의 크기 차이가 심하여 결정의 정상적인 성장을 방해하는 물성을 나타냈고, V5+, Cr3+ 이온은 흑색의 결정, Fe3+ 이온은 적갈색의 결정으로 성장되었다. Al3+, Zr4+, Al3+의 순서로 투과도가 높아지는 것이 관찰되었다. 불순이온의 농도에 따른 영향으로서 Al3+ 이온의 경우 주입농도가 높아질수록 low angle boundary와 oxygen deficiency가 감소하였고, 투과율은 조금 감소하거나 큰 차이가 없는 것으로 나타났다. 반면에 Cr3+ 이온을 주입한 경우 0.003 atomic%에서 최적의 물성을 보였으며, 주입농도가 높아질수록 결정성장이 어려워지고 광의 투과도가 급격히 저하되었다.