• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.13 no.2
• /
• pp.131-140
• /
• 2015

This research studied a scaling analysis for the selection of proper heat generation at tube for 1/4-scale storage vaults. First of all, the temperature field and velocity distribution of an original scale storage vault were analyzed and then numerical analysis of a 1/4-scale storage vault was performed to compare each model. The proper heat generation for a 1/4-scale storage vault, at which the temperature and velocity field of a 1/4-scale storage vault showed the best agreement with that of the original storage vault, was evaluated with proposed dimensionless parameters. The behavior of temperature and velocity of fluid in the 1/4-scale case were most similar to those of the original scale, using a heat flux 1.3 times higher than that seen in the original scale, which was approximately 190 W.

• Journal of Convergence for Information Technology
• /
• v.12 no.3
• /
• pp.141-150
• /
• 2022

Fluid flow and thermal characteristics of laminar nanofluid(water/Al2O3) flow in a circular U-bend tube have been studied numerically. In this study, the effect of Reynolds number and the solid volume fraction and the impact of the U-bend on the flow field, the heat transfer and pressure drop was investigated. Comparisons with previously published experimental works on horizontal curved tubes show good agreements between the results. Heat transfer coefficient increases by increasing the solid volume fraction of nanoparticles as well as Reynolds number. Also, the presence of the secondary flow in the curve plays a key role in increasing the average heat transfer coefficient. However, the pressure drop curve increases significantly in the tubes with the increase in nanoparticles volume fraction.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6A
• /
• pp.861-872
• /
• 2008

Concrete-filled glass fiber reinforced polymer tubes are often used for marine structures with the benefit of good durability and high resistance against corrosion under severe chemical environment. Current research presents results of a comprehensive experimental investigation on the behavior of axially loaded circular concrete-filled glass fiber reinforced polymer tubes. This paper is intended to examine several aspects related to the usage of glass fiber fabrics and filament wound layers used for outer shell of piles subjected to axial compression. The objectives of the study are as follows: (1) to evaluate the effectiveness of filament winding angle of glass fiber layers (2) to evaluate the effect of number of GFRP layers on the ultimate load and ductility of confined concrete (3) to evaluate the effect of loading condition of specimens on the effectiveness of confinement and failure characteristics as well, and (4) to propose a analytical model which describes the stress-strain behavior of the confined concrete. Three different types of glass fiber layers were chosen; fabric layer, ${\pm}45^{\circ}$ filament winding layer, and ${\pm}85^{\circ}$ filament winding layer. They were put together or used independently in the fabrication of tubes. Specimens that have various L:D ratios and different diameters have also been tested. Totally 27 GFRP tube specimens to investigate the tension capacity, and 66 concrete-filled GFRP tube specimens for compression test were prepared and tested. The behavior of the specimens in the axial and transverse directions, failure types were investigated. Analytical model and parameters were suggested to describe the stress-strain behavior of concrete under confinement.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.204-207
• /
• 2001

The bending process for the circular curved tube and rectangular curved tube with fins can be developed by the hot metal extrusion machine with the multiple punches moving in the different velocity. The bending phenomenon can be controlled by the two variables. The one of them is the difference of velocity at the die exit section by the different velocity of billets through the multi-hole container. The other is the one by the different hole diameter. The results of the experiment show that the circular curved tube with fins and rectangular curved tube with pins can be formed by the extrusion process and that the curveture of the product can be controlled by the velocity of punch and diameter of container hole and that the defects such as the distortion of section and the thickness change of the wall of tube the folding and wrinkling of thin tube and fins did not happen after the bending processing by the extrusion bending machine.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.5
• /
• pp.1264-1274
• /
• 1994

Heat transfer performance of integral-fin tube which is used in recipro turbo refrigerator or high compact heat exchangers is studied. Eight tubes with trapezoidal shaped integral-fins having fin densities from 748 to 1654 fpm and 10, 30 internal grooves are tested. A plain tube having the same(inner and outer) diameter as the fin tubes is also tested for comparison. Pool boiling heat transfer of R-11 is investigated experimentally and theoretically on single tube arrangement. The refrigerant evaporates at saturation state of 1 bar on the outside tube surface and heat is supplied by not water which circulates inside of the tube. From the result of eight fin tubes and one plain tube tested, a tube having 1299 fpm-30 grooves shows the best performance. A maximum overall heat transfer coefficient of this tube is about 4000 $W/m^{2}K$ at 2.8m/s of water velocity. The maximum heat transfer enhancement (i.e., the ratio of overall heat transfer coefficients of finned to plain tubes)is about 2.1.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.5
• /
• pp.1275-1287
• /
• 1994

Heat transfer performance improvement by fin and grooves is studied for condensation of R-11 on integral-fin tubes. Eight tubes with trapezoidal shaped integral-fins having fin densities from 748 to 1654 fpm and 10, 30 grooves are tested. A plain tube having the same diameter as the finned tubes is also tested for comparison. R-11 condenses at saturation state of $32^{\circ}C$ on the outside tube surface cooled by inside water flow. All of test data ate taken at steady state. Beatty and Katz's, Rudy's and Webb's theoretical models are used to predict the R-11 condensation coefficient of tubes having 748, 1024 and 1299 fpm. The predicted value by Betty and Katz's model is within 10% of experimental values in this study at fpm<1024 and Rudy's model predicted the experimental data at fpm>1024 within 15%. The tube having fin density of 1299 fpm and 30 grooves has the best overall heat transfer performance. This tube shows the overall heat transfer coefficient of 11500 $W/m^{2}K$,/TEX> at coolant velocity of 3.0m/s.

• Journal of ILASS-Korea
• /
• v.19 no.2
• /
• pp.69-74
• /
• 2014

The comparison of the flow characteristics between circular and swirl jets which were controlled by the spinner attachment inside the airtube were conducted in this study. Swirl jet means a flow in whirls by mixing the flow of axial and tangential direction. Swirl flow has been used for the improvement of the combustion efficiency in the combustor. This flow is controlled by the spinner which has several vanes inclined by certain angles to the axial direction. In this study, angle of vane $30^{\circ}$ and diameter ratio of outlet to inlet of the airtube 0.73 were made. These spec. should find on the general gun type burner built in the domestic small size boiler. As the flow characteristics, axial and tangential velocities were measured by using the 2-D hot-wire velocimeter system and analyzed statistically. And also this research conducted a practical experiment considering to the attached belongings likes as ignitor, nozzle etc. on the airtube of the gun type burner. As a result, swirl occurred at the occasion of beingness and flow region extended considerably toward the radial direction. But effect of swirl did not transmit to the downstream. And the complicated flow was appeared regardless of the existence of spinner because of the effect of belongings.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.4
• /
• pp.181-187
• /
• 2018

In this paper, sound absorption of micro-perforated elastic plates installed in an impedance tube of a circular cross-section is discussed using an analytic method. Vibration of the plates and sound pressure fields inside the duct are expressed in terms of an infinite series of modal functions, where modal functions in the radial direction is given in terms of the Bessel functions. Under the plane wave assumption, a low frequency approximation is derived by including the first few plate modes, and the sound absorption coefficient is given in terms of an equivalent impedance of a single surface. The sound absorption coefficient using the proposed formula is in excellent agreement with the result by the FEM (Finite Element Method), and shows dips and peaks at the natural frequencies of the plate. When the perforation ratio is very small, the sound absorption coefficient is dominated by the vibration effect. However, when the perforation ratio reaches a certain value, the sound absorption is mainly governed by the rigid MPP (Micro-Perforated Plate), while the vibration effect becomes very small.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.136-141
• /
• 1993

진공챔버,위생튜브등 정밀한 내면을 필요로 하는 경우 표면거칠기를 향상시키기 위한 방법으로 전해가공 및 수작업을 하는 경우가 대부분인데 이는 가공비가 비씨고 다듬질 시간이 많이 걸리는 등 매우 비경제적이다. 더구나 길이가 긴 관이나 구부러진 관의 내면은 기계적으로 다듬질이 매우 어렵다. 그러나 최근에 개발된 전자기장을 이용한 자력 연마가공법은 기존의 기계적인 가공법과는 달리 실제 가공을 행하는 공구부와 ㅣㅇ를 구동하는 구동부 사이에 공극을 허용하기 때문에 이를 이용하여 회전이 불가능한 곡관의 내면다듬질을 가능하게 하였다. 지금까지 연구들은 단순히 전자석 및 전원으로 이루어진 수동가공 시스템으로서 가공공정 자체의 특성파악에 집중되어 왔으나 자력연마법의 장점중의 하나인 다듬질 공정의 자동화 가능성을 실현시키기 위해서는 공정의 제어가 필요하다. 본 연구에서는 이를 실현시키기 위한 기초연구로서 컴퓨터구동 회전자력연마가공 시스템을 개발하고 그 기본특성을 알아보기 위해 유한요소법을 이용하여 원형 요오크 및 여섯개의 자극에 대해 자력선의 분포를 알아보았다. 또한 이로부터 가공영역의 자속밀도를 계산하고 다듬질 가공을 가능케 하기위한 회전자화의 발생방법에 대해 고찰하였다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.210-210
• /
• 2003

휘스커상의 뮬라이트의 생성온도와 속도는 출발물질로 사용되는 알루미나와 실리카의 화학적 순도, 입자크기 그리고 결정형태에 의존하며, 알루미나와 실리카의 조성비에 따라 생성되는 뮬라이트의 형태가 변한다. 각 원료에 대한 반응성을 관찰하기 위하여 출발원료인 Al(OH)$_3$, 비정질 SiO$_2$, AlF$_3$를 혼합 각각 단일조성과 2상 및 3상의 원료를 혼합 분쇄하여 분무건조한 조립분말을 5$0^{\circ}C$ 구간으로 나누어 상온에서 130$0^{\circ}C$까지 튜브 로에서 열처리하였다. Al(OH)$_3$와 AlF$_3$를 단독으로 열처리하였을 경우에는 안정한 상태로 열처리가 진행되었으나, 혼합하였을 경우에는 40$0^{\circ}C$ 이상의 온도에서 서서히 반응하였다. 각 온도구간에서 열처리한 시편은 미세구조 관찰과 상분석을 통하여 플루오르 토파즈와 휘스커상의 뮬라이트의 생성을 관찰하였으며, 생성된 휘스커 뮬라이트는 조립의 형상을 원형대로 보존하였으며, 조립의 강도를 측정하기 위하여, 초음파 분산기와, 초음파 Homgeniger를 이용하여 처리한 결과 대부분 원래의 형상을 유지하였다.