• Korean Journal of Optics and Photonics
• /
• v.16 no.3
• /
• pp.287-294
• /
• 2005

In this paper, an optical true time-delay (TTD) for two-dimensional (2-D) phased array antennas (PAAs), composed of a multi-wavelength optical source and a fiber optic delay line matrix consisting of $2\times2$ optical switches with optical fiber connected between cross ports, has been proposed. A 2-bit $\times4-bit$ optical TTD for 10-GHz 2-D PAAs has been implemented by cascading a wavelength dependent TTD (WD-TTD) and a wavelength independent TTD (WI-TTD). The unit time delay for WD-TTD and WI-TTD have been chosen as ${\Delta}T=12ps$ and $\Delta\tau=6ps$, respectively. Time delay have been measured at all radiation angles. The maximum delay error for WD-TTD was measured to be 3 ps due to jitter incurred from gain switching. For the case of WI-TTD, error was within ${\pm}\;1\;ps$. The proposed optical TTD for a 2-D PAA has the following advantages: 1) higher gain compared to one-dimensional linear PAAs, 2) stabilization of optical power and wavelength by using a multi-wavelength optical source, and 3) fast beam scan and simple operation due to electronic control of the $2\times2$ optical switches matrix on a column-by-column basis.

• Membrane Journal
• /
• v.25 no.2
• /
• pp.132-143
• /
• 2015

Water is an essential resource for humans, but fresh water becomes scarce due to population growth and contamination of limited resources. Membrane technology has been widely used for water treatment, and forward osmosis is a process which does not need high hydraulic pressure for the operation. However, there are needs for (1) development of novel draw solutes causing low internal concentration polarization and reverse salt flux for high water flux, and (2) development of economic recovery method of the draw solutes in the diluted draw solution. Previous researches on the draw solute include $NaHCO_3$ which can be regenerated by about $60^{\circ}C$ heating, sucrose which can make potable water without additional process, and magnetic nanoparticles which can be regenerated by external magnetic field. Using the principles of forward osmosis process, sea water desalination, wastewater treatment, refinement of proteins, energy generation using pressure retarded osmosis process, preparation of diluted fertilizer, and growing algae for biofuel can be conducted. This paper summarizes characteristics of ideal draw solutes, recovery method of the draw solutes, and various application examples.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.6A
• /
• pp.634-639
• /
• 2006

In this paper an MMIC 2-stage power amplifier is designed and fabricated for 5GHz wireless LAN applications using $0.5{\mu}m$ gate length PHEMT transistors. The PHEMT gate width is optimized in order to meet the linearity and efficiency of the MMIC power amplifier. The $0.5{\mu}m\times600{\mu}m$ PHEMT for the drive stage and $0.5{\mu}m\times3000{\mu}m$ PHEMT for the amplification stage are the optimized sizes to achieve more than 25dBc of third order IMD at the power level of 3dB back-off from the input P1dB and more than 22dBm output power under a supply voltage of 3.3V. The two-stage MMIC power amplifier is designed to be used for the both of HIPERLAN/2 and IEEE 802.11a because of its broadband characteristics. The fabricated PHEMT MMIC power amplifier exhibits a 20.1dB linear power gain, a maximum 22dBm output power, a 24% power added efficiency under 3.3V supply voltage. The input and output on-chip matching circuits are included on a chip of $1400\times1200{\mu}m^2$.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.6
• /
• pp.560-568
• /
• 2005

The proposed Multi-level PDP sustain Driver is composed of the semiconductor devices with low voltage rating compared to those used in the prior circuit proposed by L. Wether, and it has two resonant periods during the charging (rising period) and discharging (falling period) the PDP in the sustaining voltage waveforms. In accordance with the change of timing phase$(T_{r1},\;T_{i1},\;T_{r2})$, the performance characteristics of a commercial PDP module has been carried out and compared the characteristic with the 42V6, made of LG Electronics co., Experimental results show that the performance characteristics of PDP module are greatly influenced by the variation of $T_{i1}\;and\;T_{r2}$. The variation of $T_{r1}$ do not influence much on the performances of PDP. With the conditions that $T_{r1}=60ns,\;T_{i1}=120ns,\;and\;T_{r2}=350ns$, we could get the performances listed as the luminance is increased $14.6\%$, the power consumptions is decreased $5.9\%$, the panel efficiency is increased $24.2\%$, module efficiency is increased $21.2\%$, compared to those shown in the commercial PDP module (42V6). Therefore, the proposed multi-level PDP sustain driver expected to be suitable to actual PDP module application.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.11
• /
• pp.7990-8000
• /
• 2015

Plant factories are plant cultivation systems which produce farm products uniformly under the controlled environmental condition regardless of seasons and places. Thermal flow in the plant factory is an important parameter in cultivating plants. In this research, we study thermal flow characteristics for a hybrid plant factory with multi-layer cultivation shelves using computer simulation techniques. In order to obtain numerical solutions for thermal flow characteristics, a finite volume method was applied. We consider a low-Reynolds-number ${\kappa}-{\epsilon}$ turbulence model, incompressible viscous flows, and pressure boundary conditions for numerical simulation. Commercial software Solid Works Flow Simulation is then used to investigate characteristics of thermal flows in the plant factory applying several different inflow air velocities and arrangements of cultivation shelves. From numerical analysis results, we found that temperatures in cultivation shelves were uniformly distributed for Case 3 when the inflow air velocity was 1.6 m/s by using a blower in the plant factory. However in Case 1 lower temperature distributions were observed in test beds, TB2 and TB3, which indicated that additional temperature control efforts would be required. Average shelf temperature increased by $3^{\circ}C$ using artificial light source (DYLED47) with 50% blue and 50% red LED ratios. Korea Academia-Industrial cooperation Society.

• The Korean Journal of Pesticide Science
• /
• v.10 no.4
• /
• pp.351-358
• /
• 2006

This study was conducted to evaluate herbicidal properties of picolinafen in terms of crop safety, weed control spectrum, application window, residual efficacy and resistant weed control. Herbicidal phytotoxicity of picolinafen to wheat and barley was greatest when applied at 0 days after sowing (DAS), but decreased significantly as plant growth advanced. Picolinafen showed greater activity against broadleaved weeds than grass weeds. Picolinafen showed highest activity when it was applied at early post emergence timing (5 to 15 DAS), and showed significantly decreased activity at 20 DAS application. The $LT_{50}$ values (the period from application required for residual control by 50%) was 9.3 and 6.5 days against Digitaria ciliaris and Brasica naus at 60 g ai $ha^{-1}$, respectively. Picolinafen showed similar activities against both triazine resistant and sensitive Amaranthus retroflexus. Collectively, picolinafen appeared to have a good fitness to control resistant broad leaved weeds control by early post emergence application.

• Applied Biological Chemistry
• /
• v.41 no.7
• /
• pp.527-532
• /
• 1998

This study was aimed at the development of the rice product by fermentation of saccharified rice solution with Bifidobacterium. To optimize the preparation of saccharified rice solution for Bifidobacterium fermentation, various pretreatment conditions were established. Grinding for 30seconds by an impact mill was more efficient than any other grinding schemes tested. The preheating before gelatinization showed a positive effect for efficient saccharification, and its optimal conditions were at $60^{\circ}C$ for 45 min. The optimum gelatinization conditions were at $100^{\circ}C$ for 40 min. The optimum levels of enzymes for saccharification of rice were 0.135 unit/g rice powder for ${\alpha}-amylase$ and 3.375 unit/g rice powder for glucoamylase, respectively. The physico-chemical properties of the fermented product by a fastidious Bifidobacterium showed a great potential for a functional rice product. However, an improvement on its flavor was required, which might be achieved by the addition of various fruits and vegetables.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.11
• /
• pp.2689-2696
• /
• 2015

Radioactive isotopes which are manufactured using a cyclotron in a radioisotope used for radiation diagnosis is affected by the production yield according to size and shape of the beam and beam uniform degree from irradiated location when the proton beam investigated the target by cyclotron. Therefore, in this paper developed the BPM(Beam Profile Monitor) device capable of measuring the beam cross-section at the cyclotron beam line. It was configured so as to be able to remote control the BPM device in LabView and used the BPM program it was to be able to easily monitor and display to analyze the graph of two-dimensional graph and a three-dimensional beam distribution numerical information of the beam obtained while scanning the tungsten wire to the X and Y axis. The time it takes to measure the beam can be confirmed 37seconds when step motor driving speed was 2000pps. Through a beam readjusted based on the measured beam distribution information by optimizing the beam distribution it can be made to maximize the RI production yield and contribute supply stabilization.

• Journal of the Institute of Convergence Signal Processing
• /
• v.11 no.4
• /
• pp.338-344
• /
• 2010

Both ends of welding line are often closed by wall in the welding of ship blocks. In this research, seam tracking sensing system for butt welding in the condition with wall was developed. Seam tracking sensing system measures position of carriage from wall and detects root-pass of welding line. The system consists of the laser displacement sensors and ultrasonic sensors. The laser displacement sensor reciprocal1y rotates by the motor and measures a distance from laser sensor to the welding material. The ultrasonic sensor measures a distance between welding system and walls. The distance measured by the ultrasonic sensor is used to get X(driving) position and to determine initial and end point of the weld line. Y(weaving) and Z(height) of the weld line are obtained by the distance measured by the laser displacement sensor and the orientation of the sensor. The sensing system includes the controller that is independent from the welding carriage. The seam tracking sensing system is attached to both side of welding carriage so that interference between welding torch and sensing system can be avoided during the welding. And both side sensing system minimize dead zone. Finally, developed sensing system was adhered to welding carriage and verified usefulness by experiments.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.279-279
• /
• 2007

비휘발성 메모리 Fe-RAM은 빠른 정보처리 속도와 전원공급이 차단되었을 때도 계속 정보를 유지할 수 있는 비휘발성 특징과 더불어 저전압, 저전력 구동의 장점이 있어서, 차세대 메모리로 많은 주목을 받고 있다. FeRAM에 사용되는 강유전체는 주로 Pb(Zr,Ti)$O_3$가 적용되었는데, 최근에는 비납계 강유전체의 연구도 활발히 이루어지고 있다. 이러한 비납계 강유전체 중에서 가장 특성이 우수한 물질은 $(Bi,La)_4Ti_3O_{12}$ (BLT) 이다. 그런데 BLT는 결정 방향에 따른 강한 이방성의 강유전 특성을 나타내기 때문에 BLT 박막을 이용하여 Fe-RAM 소자 등을 제작하기 위해서는 결정의 방향성을 세심하게 제어하는 것이 매우 중요하다. 지금까지 연구된 BLT 박막의 방향성 조절결과를 보면, BLT 박막을 스핀 코팅 법 (spin coating method)으로 증착하고, 핵생성 열처리 단계를 조절하여 무작위 방향성을 갖는 박막을 제조하는 방법이 일반적이었다. 그런데 이러한 스핀 코팅법에서의 핵생성 단계의 제어는 공정 조건 확보가 너무 어려운 단점이 있다. 이러한 어려움을 극복할 수 있는 대안은 스퍼터링 증착법(sputtering deposition method), PLD (pulsed laser deposition)법 등과 같은 PVD (physical vapor deposition) 법의 증착방법을 적용하는 것이다. PVD 법으로 증착하는 경우에는 이미 박막 내에 무수한 결정핵이 존재하기 때문에 핵생성 단계가 필요가 없게 된다. PVD 증착법의 적용을 위해서는 타겟의 제조 및 평가 실험이 선행되어야 한다. 그런데 벌크 BLT 재료의 소결공정 조건과 전기적 특성에 관한 연구 결과는 거의 발표가 되지 않고 있다. 본 실험에서는 $Bi_2O_3,\;TiO_2,\;La_2O_3,\;Nb_2O_5\;and\;Al_2O_3$ 분말들을 이용하여 최적의 조성을 구하기 위하여 $Nb^{+5}$ 와 $Al^{+3}$을 $Ti^{+4}$ 자리에 소량 치환시켜 제조하였다. 혼합된 분말을 하소 후 pellet 형태로 성형하여 소결을 실시하였다. 시편을 1mm 두께로 연마하고, 양면에 silver 전극을 인쇄하여 전기적 특성을 측정하였다. 측정결과 $Ti^{+4}$ 자리에 $Nb^{+5}$를 치환하여 제조한 시편에서 $2P_r{\sim}31\;{\mu}c/cm^2$정도의 매우 우수한 특성을 얻었다.