• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.05a
• /
• pp.558-559
• /
• 2018

The harness wiring serves as an intermediary for transmitting the electrical signals necessary to drive the vehicle and is highly influenced by vehicle performance. Wire harness tester performs assembly test. Harness products are operated with the function of checking 0 and 1. Proceed to inspection in wire assembly process. There is a defect in the finished vehicle during use. We want to improve such defects. We design the FPGA and propose the measurement device design and the simulation result that the line and the line are disconnected by ADC precision harness inspection.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.5
• /
• pp.501-507
• /
• 2005

This paper proposes a Hybrid Random PWM(HRPWM) technique using a LF2407 DSP board in order to spread the power spectra of an induction motor. The proposed method is composed to the PRBS (Pseudo-Random Binary Sequence) with the Lead-Lag random bit and the random triangular carrier for the logical comparison. Also, a DSP generates the random number, the PRBS and the three-phase reference signal, a MAX038 chip operating as frequency modulator generates the random triangular carrier. For verification of the proposed method, the experiments were conducted with a three-phase adjustable speed a.c drives, and the results of simulations and experiments are presented.

• Proceedings of the Korean Information Science Society Conference
• /
• 2008.06d
• /
• pp.470-475
• /
• 2008

6LoWPAN 센서 노드의 이동성을 지원하기 위해 기존의 Mobile IPv6 (MIPv6)와 같은 프로토콜을 활용하는 것은 저전력에 제한적 사양의 하드웨어로 구성된 6LoWPAN 센서 노드에서 구동되는 것이 현실적으로 불가능하다. 따라서 Mobile Access Gateway (MAG)가 6LoWPAN 센서 노드의 이동시 발생하는 바인딩 시그널링을 대신 처리해주는 Proxy Mobile IPv6 (PMIPv6) 프로토콜을 6LoWPAN에 적용하면 효율적으로 이동성을 지원할 수 있다. 하지만 Proxy Mobile IPv6는 6LoWPAN 이동 센서 노드와 1홉으로 연결되는 경우에 6LoWPAN 이동 센서 노드의 이동을 인지하고 Proxy Binding Update(PBU)를 하게 되지만, 6LoWPAN 센서 네트워크와 같이 멀티 홉으로 구성되는 네트워크에는 Proxy Mobile IPv6를 바로 적용할 수 없다. 따라서 본 논문에서는 기존의 1홉 단위로 연결된 6LoWPAN 이동 센서 노드의 이동성을 지원하는 Proxy Mobile IPv6 프로토콜을 멀티를 환경의 6LoWPAN 센서 네트워크에 적용하기 위한 방법을 제안한다.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.2
• /
• pp.104-109
• /
• 2007

Single fuel cell was fabricated with a MEA (membrane electrode assembly) that had a $4cm^2$ active area and with silicon bipolar plates those were introduced to miniaturize the fuel cell by replacing heavy weight graphite plates. Optimum humidification condition for the single cell was selected based on performance results obtained varying humidifier temperature at a fixed feed rate of hydrogen and oxygen. Furthermore, to study the effect of humidification condition on the performance of a fuel cell stack, the fuel cell stack consisting of two MEAs and silicon bipolar plates was studied, then problems and characteristics of silicon-based fuel cell stack were examined.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.1
• /
• pp.55-62
• /
• 2011

In this study, we tried to improve the thrust control performance through the thrust control combustion experiment of the hybrid rocket. We constructed the system which controls the oxidizer flow by combining a needle valve with a stepping motor and controlling the stepping motor drive according to the thrust control command order. Gas oxygen was used as the oxidizer for two different propellants, PE(Polyethylene), PC(Polycarbonate), respectively. To improve the slow response time and the oscillation phenomenon in the beginning stage of the thrust control combustion experiment, we measured and analyzed the change of the flow speed of the propellant pipe. The revised thrust control combustion experiment showed that the thrust was stably controlled with the margin or error from the thrust command within ${\pm}1$ N.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.1
• /
• pp.40-47
• /
• 2010

In this study, basic research on the thrust control by controling oxidizer mass flow rate of a $GO_2$/PE hybrid rocket is presented. For this purpose, hybrid rocket system including oxidizer flow control system and data acquisition system was developed. To control oxidizer mass flow rate, we used needle valve with stepping motor which was controled by LabVIEW program. During the fundamental experiments, this system managed to follow the pre-programmed (20 N - 10 N - 20 N - 0 N) thrust level.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.5
• /
• pp.36-43
• /
• 1999

A new design of a Direct Digital Frequency Synthesizer(DDFS) is presented, where a pipelined Coordinate Rotate Digital Computer(CORDIC) circuit is employed to calculate amplitude values of all the phase angles of sinusoidal waveforms produced. a near-optimal number of pipeline stages is determined based on an error analysis of calculated amplitude values in terms of the number of bits. The DDFS was implemented using a field programmable gate array, yielding a stable operating frequency of 11.75MHz. The measurement results show higher resolution, faster operating speed and simpler fabrication process, compared to ROM-based counterparts. The CORDIC-based DDFS yields 5 times higher resolution than conventional ROM-based versions.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.1
• /
• pp.58-66
• /
• 2002

Acousto-optical wavelength tunable optical filters in LiNbO$_3$ have been demonstrated using taperd directional weighted coupling acoustic waveguides and Ti double diffusion technique. Conversion efficiency in excess of 61%, 86% and sidelobe intensity of -14.29㏈, -14.99㏈ were measured at a wavelength of 1551.1nm RF frequency of 173.58MHz and RF power of 35㎽ for both TE and TM input polarizations, respectivelv. A spectral width of ~l.8nm and linear tuning late of 8.6nm/MHz were demonstrated. A 2.82$mutextrm{s}$ switching time has been measured. With two channels with 2.5nmseparation, channel cross-talk was lower than -l4㏈ for single wavelength filtering due to sidelobe.

• Progress in Medical Physics
• /
• v.10 no.1
• /
• pp.9-15
• /
• 1999

The oxygen saturation of blood can be measured by the difference absorption in optical spectra of Hb and Hb0$_2$, as the well known previous study. In this study we developed the non-invasive oxygen measurement device for diagnosis of peripheral vascular disease in lower extremity using infrared and red LED which produce a peak spectral emission at a wavelength of 660 nm, and 940 nm. To evaluate the clinical application of the oxygen measurement device, we performed lower extremity study to measure the oxygen changes in response to physiological changes within biological tissue. The results showed that oxygen saturation of blood in biological tissue can be monitored from the separation arrangement light source and detector.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.991-995
• /
• 2002

The engine booming noise heard inside a vehicle's cabin is due to the engine vibration that's transferred to the chassis in the form of structural vibration and it often causes discomfort to the passenger. In an effort to seek out the possible relation between the engine booming noise and the engine vibration of a vehicle, a position on the engine mount was selected and the vibration transmission through the position was attenuated to observe the corresponding change in the noise level inside the cabin. A system consisting of an actuator and a hybrid controller that has both the feed-forward and feed-back capabilities was developed in order to carry out the experiment.