• Journal of Ocean Engineering and Technology
• /
• v.11 no.4
• /
• pp.130-140
• /
• 1997

원형주상체 주위의 유동을 규명하기 위해 회류수조에서 원주방향으로 24개의 위치에 대하여 압력을 계측하였으며, laser sheet을 이용하여 유동을 가시화 하였다. Reynolds수가 4800에서 40000인 범위에 대하여 실험을 수행하였다. 또한, 원형단면체 주위의 비정상 층류유동에 대한 Navier-Stokes방정식의 해를 구하는 수치해석기법을 개발하였다. 효과적인 격자배치를 위하여 H와 O-type의 중첩격자를 사용하였고, 이산화 방법으로는 정규격자시스템에서 유한차분법을 적용하였다. 실험과 수치해석결과에서 뚜렷한 와류박리현상을 볼 수 있었으며, 압력계수 (C$_{p}$ ), 항력계수(C$_{D}$), 스트로얼수(St)를 정량적으로 비교하였을 때, 비교적 잘 일치하는 것을 확인하였다.다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.8
• /
• pp.20-28
• /
• 2004

For the prediction on the onset of oblique shock wave-induced vortex breakdown, computational studies on the Oblique Shock wave/Vortex Interaction (OSVI) are conducted and compared with both experimental results and analytic mode1. A Shock-stable numerical scheme, the Roe scheme with Mach number-based function (RoeM), and a two-equation eddy viscosity-transport approach arc used for three-dimensional turbulent flow computations. The computational configuration is identical to available experiment, and we attempt to ascertain the effect of parameters such as a vortex strength, streamwise velocity deficit, and shock strength at a freestream Mach number of 2.49. Numerical simulations using the k-w SST turbulence model and suitably modeled vortex profiles are able to accurately reproduce many fine features through a direct comparison with experimental observations. The present computational approach to determine the criterion on the onset of oblique shock wave-induced vortex breakdown is found to be in good agreement with both the experimental result and the analytic prediction.

• Journal of the Korean Institute of Gas
• /
• v.25 no.1
• /
• pp.14-19
• /
• 2021

The change of the vorticity and the temperature distribution in heat exchanger tube bank were analyzed for the flows with the constant inlet velocity and the sinusoidal inlet velocity. The flow frequency characteristics were examined by analyzing power spectral density of lift and drag at a typical circular tube in the tube bank. Karman vortex street could be seen at the upstream region of tube bank for the case of constant inlet velocity. It could be seen that the Karman vortex street was affected by the change of inlet velocity near the circular tubes for the case with the sinusoidal inlet velocity. It was observed that the unsteady temperature distributions for both inlet velocity conditions had almost the same motion as the flow vorticity behavior. The flow frequency for the case with the constant inlet velocity is 37.25Hz, and that with the sinusoidal inlet velocity, the flow frequency is 18.63Hz, which is equal to the sinusoidal inlet velocity. The mean surface Nusselt number(Nu) for overall heat exchanger tube bank was 1051 for the case with the constant inlet velocity and 1117 for the case with the sinusoidal inlet velocity. From the result of heat transfer analysis, it could be seen that Nu with the sinusoidal inlet velocity showed 6.3% increase than that with the constant inlet velocity.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.7 no.3
• /
• pp.45-52
• /
• 2003

Detailed flowfield resulting from the secondary sonic gas injection into a divergent section of supersonic conical nozzle has been numerically investigated. The three-dimensional flowfield associated with the bow-shock/boundary-layer interaction inside the nozzle has been solved by Reynolds-averaged Navier-Stokes equations with an algebraic and $\kappa$-$\varepsilon$ turbulence model. The numerical results have been compared with the experimental results for the identical flow conditions, and it is shown that the comparison is satisfactory Effects of different injection pressures of the secondary jet on the shock/boundary-layer interactions and the overall flow structure inside the nozzle have been investigated. The vortex structures behind the shock interaction and wall pressure variations have also been studied.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.6
• /
• pp.2132-2146
• /
• 1991

Extensive experiments were carried out to investigate the mass transfer and flow structures around a circular cylinder with annular fins in crossflow. The naphthalene sublimation method was employed to measure the circumferential and longitudinal variations of mass transfer from the circular cylinder between annular fins and H is the height of the fin from the cylinder surface. A remarkable enhancement of mass transfer due to the horseshoe vortices was observed near the corner junction between the annular fin and circular cylinder. The present results indicate that the local circumferential Sherwood number shows the higher values on the front stagnation point. The maximum augmentation of mass transfer rate at the center of cylinder is found near L/H-0.15 due to the separation bubble along the annular fins. The secondary flows, which are the corner vortices V2 and V3 near the end wall of the annular fin, are fairly predicted from the distributions of local Sherwood number in the spanwise direction. The average Sherwood number of overall surface at L/H=0.15 is larger 2.0 times than that of without annualr fins. The correlations of total average mass transfer rate with L/H and Re$_{L}$ can also be obtained.d.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.729-732
• /
• 2010

The present study has been motivated by the development of a reliable numerical methodology for simulation of kerosene/LOx coaxial swirl injectors. To deal with thermodynamic non-ideality and anomalies of transport properties pronounced at supercritical pressures, a set of subroutine libraries has been constructed based on the cubic equations of state, and applied to an existing flamelet analysis code. For computational efficiency, two-dimensional axisymmetric RANS formulation with swirl was adopted and validated successfully against an isothermal coaxial swirling jet. For the actual problem with high pressure combustion, however, numerical results show that the RANS models yield excessive production of turbulence probably due to high density gradient magnitude in the vicinity of mixing layer of swirling film flow, and imply strongly further improvement of the turbulence models.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.8
• /
• pp.521-529
• /
• 2017

Three-dimensional flow characteristics within a high-acceleration first-stage turbine vane passage has been investigated in a newly-built vane cascade for propulsion. The result shows that there is a strong favorable pressure gradient on the vane pressure surface. On its suction surface, however, there exists not only a much stronger favorable pressure gradient than that on the pressure surface upstream of the mid-chord but also a subsequent adverse pressure gradient downstream of it. By employing two different oil-film methods with upstream coating and full-coverage coating, a four-vortex model horseshoe vortex system can be identified ahead of each leading edge in the cascade, and the separation line of inlet boundary layer flow as well as the separation line of re-attached flow is provided as well. In addition, basic flow data such as secondary flow, aerodynamic loss, and flow turning angle downstream of the cascade are obtained.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.9
• /
• pp.1-8
• /
• 2003

Velocity data were acquired at a series of stations in the chordwise direction above a delta wing with leading edge extension, using a triple axis hot film anemometry. Surveys normal to planform yield velocity field data at incidence angle of 24$^{\circ}$and 32$^{\circ}$at a centerline chord Reynolds number of $1.76{\times}10^6$. Experimental results of velocity measurements of mean velocity of three components gave a confidence to quantitative investigate the vortical flow field over a LEX-delta wing with this probe. The present experiments indicated the existence of both wing and LEX vortex where the local mean axial velocity is maximum. It also shown the development of secondary vortex of opposite sign of rotating above the wing surface near the leading edge. The insertion of probe across the flow field was found to have little influence on the position of the vortex core.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.1
• /
• pp.1-9
• /
• 2007

Numerical simulation is conducted to investigate aerodynamic force generation mechanism for the "figure-of-eight" motion of Dipteran fly, Phormia-Regina. Wing trajectory is referred to experimental result, which was observed from the tethered flight under freestream condition. Numerical simulation shows that the lift is mainly generated during downstroke motion and the large amount of thrust is generated abruptly at the end of upstroke motion. In the present work, vortical structure in the wake and the pressure field around the airfoil are examined to understand the generation of lift and thrust. Consequently, the lift generation is related with the leading edge vortex which is developed by an effective angle of attack. And the thrust generation can be explained by vortex pairing in the flow field and by vortex staying in the pressure field.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2012.06a
• /
• pp.289-290
• /
• 2012

본 연구에서는 고정식 해양구조물의 지지각으로 사용되는 원형실린더에 나선형 판을 부착하여 와류유기진동에 미치는 영향을 고찰하였다. 연구의 목적을 달성하기 위해 $Re=6.5{\times}10^3$의 균일유입유동에서 2-프레임 그레이레벨 상호상관 PIV기법을 이용한 실험적인 방법을 적용하였다. 모델의 직경은 40mm이며 후류 유동구조, 난류강도, 응력분포에 대한 통계적 유동정보를 계측하였다. 실험결과로는 원형실린더와 뱃전판을 부착한 실린더와의 비교를 통해 뱃전판의 유동특정을 평가하였으며, 뱃전판의 영향은 후류에서 와의 생성과 소멸 메커니즘의 변화에 큰 영향을 미치고 후류 칼만 와열의 안정적인 제어를 통해 와류유기진동을 억제하였다.