• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.148.1-148.1
• /
• 2012

로켓 혹은 우주발사체의 주엔진에는 대부분 연료와 산화제를 연소시켜 나오는 에너지를 사용하는 화학로켓이 주종을 이루어 왔다. 이러한 로켓엔진에서 그동안 연료로는 수소계, 탄화수소계, 아민계 등 다양한 화학물질이 사용되어 왔으나, 산화제로는 강한 산화성을 나타내면서 밀도가 높은 몇몇 물질만이 제한적으로 사용되어져 왔으며, 최근에는 주로 액체산소(LOx)와 사산화질소(N2O4)가 사용되고 있다. 그러나 산화제 중 액체산소는 극저온이면서 상대적으로 밀도가 낮고, 사산화질소는 강한 독성을 지니고 있으며 액체로 존재하는 구간이 좁아 연구 목적의 소형발사체를 구현하는 것에는 많은 어려움이 있다. 이러한 이유로 최근 소형발사체 개발분야에서는 상온저장성이면서 친환경적인 과산화수소(H2O2)와 아산화질소(N2O)를 산화제로 활용하는 것에 대한 관심이 고조되고 있으나, 대형 추진기관을 개발하는 연구자들로부터는 액체산소를 사용할 때 보다 엔진 자체의 비추력이 상대적으로 낮다는 이유로 활용이 외면되어 온 것이 사실이다. 본 연구에서는 엔진 자체의 추진성능 보다는 사실상 발사체의 목적이라고 할 수 있는 추진단 속도증분을 성능의 지표로 삼아 평가하였으며, 결과를 통하여 과산화수소와 아산화질소의 높은 밀도가 엔진의 낮은 비추력을 충분히 보상할 수 있음을 보였다. 과산화수소와 아산화질소는 교육/연구용 소형발사체 구성에 충분히 활용가능한 산화제이며, 실제 발사에서 충분한 비행성능을 기대할 수 있는 물질로 평가할 수 있다.

• Electrical & Electronic Materials
• /
• v.8 no.5
• /
• pp.640-647
• /
• 1995

In this study, the BaTiO$\sub$3/ capacitor add to MnO$\sub$2/ like depressor and shifter were investigated for temperature or voltage compensation by structural and electrical analysis. The relative density of BCTM, generating poly crystall and formation of lattice defect, has a 90[%] over as the CaTiO$\sub$3/ come out to control grain size. The current density of BCTM2 increased non-ohmic in high-electric field but that BCTM3 and BCTM4 had a few changing. The BCTM3 and BCTM4 unformated grain boundary shown temperature compensation properties, so that the dielectric constant was low value. The curie point was near 140[.deg. C] in BCTM1 and BCTM4, but BCTM3 and BCTM4 not shown the curie point. It is found that the charging energy of BCTM4 was changed 6[%] according to rising temperature from room temperature to 417[K]. The formation of BaMnO$\sub$3/ was low dielectric constant to change frequency and temperature.

• Journal of IKEEE
• /
• v.26 no.4
• /
• pp.653-658
• /
• 2022

This paper presents a Maximum Torque per Ampere (MTPA) control algorithm for an interior permanent magnet synchronous motor (IPMSM) drive considering the permanent magnet (PM) flux linkage variations due to PM temperature variation. PM flux linkage are estimated in real time via a Gopinath style stator flux linkage observer and a torque error correction factor is calculated from the estimated PM flux linkage. A 2-dimensional (2D) MTPA look-up table (LUT) is developed to achieve the MTPA trajectory reflecting PM flux linkage variation for compensating torque error occurred by parameter variation. The proposed IPMSM control algorithm is verified through simulations.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.5A
• /
• pp.351-360
• /
• 2011

Jacket-type offshore structures are always exposed to severe environmental conditions such as salt, high speed of current, wave, and wind compared with other onshore structures. In spite of the importance of maintaining the structural integrity for offshore structure, there are few cases to apply structural health monitoring (SHM) system in practice. The impedance-based SHM is a kind of local SHM techniques and to date, numerous techniques and algorithms have been proposed for local SHM of real-scale structures. However, it still requires a significant challenge for practical applications to compensate unknown environmental effects and to extract only damage features from impedance signals. In this study, the impedance-based SHM was carried out on a 1/20-scaled model of an Uldolmok current power plant structure under changes in temperature and transverse loadings. Principal component analysis (PCA) was applied using conventional damage index to eliminate principal components sensitive to environmental change. It was found that the proposed PCA-base approach is an effective tool for long-term SHM under significant environmental changes.

• Journal of the Korean Vacuum Society
• /
• v.5 no.2
• /
• pp.139-146
• /
• 1996

Transparent and conducting Sb-doped $SnO_2$ thin films were prepared by rf magnetron sputtering technology. But it showed a serious damage phenomenon on the surface of as-deposited films. In order to avoid a damage caused in the substrate center and location facing to target erosion, a ring plate of masking glass was installed at 1.5 cm above target surface. The uniformity and electrical characteristic of $SnO_2$ thin films were evaluated by the control of optimal conditions in the magnetron sputtering operation such as rf power, sputtering gas pressure, and substrate temperature. In the experimental results using the operating conditions, the optimum temperature, which produced uniform and damageless films, shifted with the change of gas pressure. The rate was about $100^{\circ}C$/5 mTorr at rf power of 50 W Similarly, the optimum temperature in compensation for an increase of rf power shifted down to a proper rate.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.1
• /
• pp.131-139
• /
• 2012

The lateral reinforcements of concrete such as hoops and spiral bars are known to confine concrete to compensate the strength loss due to fire by reducing explosive spalling and improving the capacity of ductility. In this context, a study was conducted to investigate the residual mechanical properties of confined and unconfined concrete($f_{ck}$=60MPa) after a single thermal cycle at 300, 600, $800^{\circ}C$. The main parameters required to establish the stress-strain relationship are the peak stress, the elastic modulus, and the strain at peak stress. The knowledge of the residual mechanical properties of concrete is necessary whenever the thermally damaged structure is required to bear a significant share of the loads, even after a severe thermal accident. Based on the results obtained in this study, the residual stress of confined concrete under thermal damage is higher according to the level of confinement and the larger strain made it to have better ductility. The decreasing ratio of elastic modulus from the relationship of stress and strain was also smaller than that of unconfined concrete.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.441-444
• /
• 1997

This paper describes the bending traveling-wave type ultrasonic motor which generates the traveling wave by combining two standing waves with phase difference time and space. In +2$0^{\circ}C$~3$0^{\circ}C$, the operation characteristic of USM has represented normal condition. But in the other temperature, the operation characteristic of USM has abnormal condition, that is driving frequency, drive current and r.p.m are down. The recent USM has controller without temperature compensation. This study aimed at fuzzy controller which must follow the frequency at operation temperature and then r.p.m and torque increased.

• Korean Journal of Optics and Photonics
• /
• v.4 no.2
• /
• pp.145-156
• /
• 1993

From the optimal system specifications of optical parts in rear projection TV focused on competitive price and performances, we designed and developed projection lens which is able to be used on current broadcast standard NTSC and HDTV in common. Through the serial processes, which are initial design of all aberrations free, aspherization of the plastic lenses, optimization with tolerances and manufacturability, and athermalization, the lens was designed. The developed CRT-lens ass'y could display the 40-55 inches image and it's resolution is more than 1000 TV-lines.

• Journal of Sensor Science and Technology
• /
• v.3 no.2
• /
• pp.24-32
• /
• 1994

A force sensor of 30 MN capacity using build-up technique in which three load cells of 10 MN capacity are arranged in parallel was fabricated. A column spring element was adopted as a shape of a strain gage type load cell. Temperature compensation circuits were used to reduce the error of a load cell. It was estimated that the total error of the fabricated force sensor is less than 0.1 %. The force sensor may be used to calibrate or test material testing machines above 4.5 MN capacity in industries.

• 한국가스학회:학술대회논문집
• /
• 2006.11a
• /
• pp.123-128
• /
• 2006

This paper describes NDIR $CO_2$ gas sensor that shows the characteristics of temperature compensation. It consists of novel optical cavity that has two elliptical mirrors and a thermopile detector that includes ASIC chip in the same metal package for the amplification of detector output voltage and temperature sensor. The newly developed sensor modules shows high accuracy (less than +/-40 ppm) throughout the measuring concentration of $CO_2$ gas from 0 ppm to 2,000 ppm. After implementing the calculation methods of gas concentration, which is based upon the experimental results, the sensor module shows high accuracy less than +/- 5 ppm error throughout the measuring temperature range $(15^{\circ}C\;to\; 35^{\circ}C)$ and gas concentrations.