• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.167-175
• /
• 2007

A predictive pulse control strategy as a means of improving the energy efficiency of radiant floor heating systems is explored. Experiments at the apartment with floor heating system are conducted to assess and compare the energy performance of the predictive pulse control strategy with an existing conventional control strategy. The Results showed that new suggested PPCM( Predictive Pulse Control Method) was available to decrease the gap of $1{\sim}1.5^{\circ}C$ between maximum and minimum indoor temperature of each rooms. Therefore PPCM method was favor to radiant floor heating system which have a delay time of 10-20 minutes for heat transfer by floor layers.

• Korean Journal of Food Science and Technology
• /
• v.49 no.2
• /
• pp.162-167
• /
• 2017

A Katsuobushi smoking machine was developed and evaluated to determine its benzo(a)pyrene reducing effect. The machine was equipped with two heaters for smoking and chamber heating. The smoke-generating system was equipped with a cadmium sulfide (CdS) smoke sensor, an on/off controller, and a rotating feeder with a smoke inlet. Raw bonito was steamed and then smoked under three smoke levels. After smoking at $45^{\circ}C$ for 108 h, the benzo(a)pyrene concentrations were 5.87, 7.83, and $11.41{\mu}g/kg$ at the low, middle, and high smoke levels, respectively. The benzo(a)pyrene concentrations after low-level smoking at 45, 65, and $85^{\circ}C$ for 108 h were 5.87, 4.82, and $3.27{\mu}g/kg$, respectively. Accordingly, the optimal conditions for benzo(a)pyrene reduction were a lower smoke level and higher smoking temperature. These optimal smoking conditions can be implemented with the newly developed machine, but is not possible using a conventional Katsuobushi smoking machine.

• Journal of the Korean Institute of Gas
• /
• v.22 no.5
• /
• pp.18-23
• /
• 2018

This study tries to analyze the injection amount of injector according to the external environment temperature of CNG vehicle. Especially, We investigated the effect of low temperature environment on gas injector performance by measuring the variation of injection amount under the same conditions as in coldstart condition. This experimental compared two products with different spring characteristics. The experimental device consist of a fuel supply unit, a flowrate measurement unit, a temperature chamber, and an injector control unit (ECU). According to the test result, the initial injection amount of the injector is increased in the low temperature environment and the needle opening time is delayed according to the change of the spring length.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.1
• /
• pp.45-50
• /
• 2013

The reflector of infrared lamp is designed to the optimal circular shape through the analyses of lumination distributions with a triangular, rectangular and circular configurations of infrared lamps respectively by using Photopia. PLC is used to compare and amplify the difference between soldering temperature profile and feedback value. It is fed to IR lamp controller which adjusts the soldering temperature of PV cell. The soldering temperature measured using an infrared temperature sensor is then fed back to the PLC. The closed control loop of soldering temperature on a PV cell is implemented. The noncontact soldering device of PV cells using infrared lamp which is easily operated by HMI operation panel and controlled robustly by PLC and IR lamp controller is developed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.184-187
• /
• 2007

본 논문은 DSP Controller를 적용한 연료전지시스템의 유량제어에 관한 논문이다. 그리고 이 연구에서 사용된 시스템은 1kW급 계통연계 연료전지 시스템이다. 이 연료전지 시스템이 안정적으로 전원을 공급할 수 있도록 시스템에서 요구하는 공기 유량을 정확히 공급하도록 제어하는 것이 본 연구의 목적이다. 이 목적을 이루기 위해 공기 공급 장치에 PID 제어기를 설계하여 적용하였다. PID 제어기의 Gain값은 지글러 니콜스 Tuning 방식으로 정하였다. 이 제어기를 적용하여 실험한 결과, 적용 전 상태와 비교하면 맥동이 30% 저감하였고, 정상상태 오차가 제거되어 온도 변화와 같은 외란과 상관없이 정확한 요구 공기 유량을 공급함을 확인할 수 있었다. 그리고 부하가 변동함에 따라 해당 요구 공기 유량이 바뀔 때 1초 내에 그 요구 공기 유량을 추종하여 스택이 안정적으로 운전될 수 있도록 하였다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.823-824
• /
• 2016

In general, distribution board, panel board and motor control center can be installed over a wide area such as residence of group, building, schools, factories, ports, airports, water service and sewerage, substation and heavy industries that are used to supply converts the voltages extra high voltage into optimal voltage. There are electrical accidents due to rise of contact temperature, loose contact of bus bar, deterioration of the contact resistance, overtemperatue of the bus bars. In this paper, we propose bus bar joints monitoring system with loose connection of bus bar, measuring the joint resistance of busbars and monitoring internal and external heat. The proposed system can be reduced the electrical accidents by maintenance of busbar joints and the temperature of the conductive contact surface of busbars.

• Magazine of the Korea Concrete Institute
• /
• v.28 no.4
• /
• pp.55-59
• /
• 2016

• Journal of Welding and Joining
• /
• v.14 no.4
• /
• pp.16-23
• /
• 1996

용접변수는 재현성을 보장하기 위하여 명시되어져야 할 모든 변수라고 정의 되어질 수 있다. 이러한 용접변수는 이음 설계, 용접부 청소, 홈가공, 예열, 후열처 리, 용접법 변수(예, 용접속도, 전압, 잔류) 등이다. 이러한 용접 변수는 용접절차서 (welding procedure apecification)에 그 내용과 측정값을 기술하도록 되어 있다. 본고에서는 좁은 의미에서 용접변수인 용접전류, 전압, 용접속도, 용접부의 온도 측정 방법을 설명하고 그 활용방법에 대하여 기술하고자 한다. 이러한 용접변수는 컴퓨터 에 접속하여 측정이 이루어 지도록 하여 측정자료의 평가, 기록 및 공정제어에 이용 될 수 있다.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1408-1411
• /
• 1996

In arc welding processes, because of the complexity and nonlinearity of heat transfer phenomena, it is often difficult to design an effective control system based upon an exact mathematic model. In this paper, we simulated the welding process for various welding conditions and positions to investigate the variations of temperature distribution for those cases. Those will be used as a preinformation for developing quality control system for arc welding process.

• Horticultural Science & Technology
• /
• v.32 no.4
• /
• pp.493-498
• /
• 2014

The objective of this study was to make growth and yield models for common ice plant (Mesembryanthemum crystallinum L.) using expolinear functional equations in a closed-type plant production system. Three-band radiation type fluorescent lamps with a 12-hours photoperiod were used, and the light intensity was $200{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$. Nutrient film systems with three layers were used for plant growth. Environmental conditions, such as air temperature, relative humidity and $CO_2$ concentration were controlled by an ON/OFF operation. Leaf area, shoot fresh and dry weights, light use efficiency of common ice plant as function of days after transplanting, accumulative temperature and accumulative radiation were analyzed. Leaf area, shoot fresh and dry weights per area were described using an expolinear equation. A linear relationship between shoot dry and fresh weights was observed. Light use efficiency of common ice plant was $3.3g{\cdot}MJ^{-1}$ at 30 days after transplanting. It is concluded that the expolinear growth model can be a useful tool for quantifying the growth and yield of common ice plant in a closed plant production system.