• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.9-15
• /
• 2018

The turbochargers, which are used widely in diesel and gasoline engines, are an effective device to reduce fuel consumption and emissions. On the other hand, turbo-lag is one of the main problems of a turbocharger. Bearing friction losses is a major cause of turbo lag and is particularly intense in the lower speed range of the engine. Current turbochargers are mostly equipped with floating bearings: two journal bearings and one thrust bearing. This study focused on the bearing friction at the lower speed range and the experimental equipment was established with a drive-motor, load-cell, magnetic coupling, and oil control system. Finally, the friction losses of turbochargers were measured considering the influence of the rotating speed from 30,000rpm to 90,000rpm, oil temperature from $50^{\circ}C$ to $100^{\circ}C$, and oil supply pressure of 3bar and 4bar. The friction power losses were increased exponentially to 1.6 when the turbocharger speed was increased. Friction torques decreased with increasing oil temperature and increased with increasing oil pressure. Therefore, the oil temperature and pressure must be maintained at appropriate levels.

• Proceedings of the Korea Multimedia Society Conference
• /
• 2003.11a
• /
• pp.404-407
• /
• 2003

현재 국내외 많은 업체들이 ERP패키지를 선보이고 있다. 그러나 국내 기업들과 ERP공급업체에 따르면 구축된 ERP로 인해 재무회계, 관리 부문에서는 어느 정도 효과를 거두고 있으나 생산 및 출고 등 물류와 관계된 자동화 부문에서는 미흡한 효용성을 보이고 있다. 따라서 본 논문에서는 유류업체의 특성에 맞는 전사적자원관리 시스템을 개발하여 유류중소업체에서 연구개발에 필요한 여러 가지 정보인 사회적인 시세, 특정 기능의 제품에 대한 선호도, 물품 만족도 등 고객에 대한 정보가 통계적으로 반영될 수 있도록 하였다.

• Tribology and Lubricants
• /
• v.20 no.1
• /
• pp.27-32
• /
• 2004

This paper presents unsteady oil flow behaviors in the engine lubrication network to clarify the differences between continuous and discontinuous oil supply crankshaft system. Using commercial network analysis program, Flowmaster2, engine lubrication network system analysis were carried out. And effects of crankshaft speed and supplied oil pressure on pressure fluctuation in oil groove and oil flow rate to each bearing were analyzed.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.868-869
• /
• 2015

지하 매설된 가스배관을 정기적으로 검사하기 위해서 가스 공급 및 용역업체에서는 주로 비피과검사 탐상장비인 MFL(Magnetic Flux Leakage) PIG(Pipeline Inspection Gauge)를 사용한다. 기존의 MFL PIG는 배관 내 유체(가스,오일 등)의 전후차단 압력의 흐름을 이용해 별도의 구동장치 없이 피그를 진행시켜 배관의 결함 유무를 평가하는 시스템이다. 하지만 10기압 이하의 낮은 운영압력과 T 분기관과 같이 급격한 곡관부가 존재하는 직경 16인치 이하의 도시가스 배관에는 기존의 시스템을 적용하기 어렵다. 이처럼 기존 MFL PIG의 적용이 불가한 도시가스 배관(직경 16인치 이하)을 활주하기 위해서는 우선 비파괴검사 시스템을 견인할 수 있는 추진 로봇이 필요하고 추진로봇에 적합한 자기누설 비파괴검사 시스템의 개발이 필요하다. 또한 비파괴검사 장비의 센서 시스템은 결함신호를 탐지하여 결함의 발생유무 및 결함의 형상을 판별하는 성능도 중요하다. 본 논문에서는 16인치 도시가스 배관의 검사를 위한 자기누설 비파괴검사 시스템의 기초설계와 대상 시스템의 자기적 특성을 분석한다. 또한 배관 외벽의 결함 발생 유무에 따른 자기누설 신호의 크기 및 분포변화를 3차원 유한요소법을 이용해 해석하여, 결함 검출 신호의 특성을 분석하는데 초점을 둔다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.05a
• /
• pp.547-548
• /
• 2018

SCM(Supply Chain Management)은 초기에 생산의 효율성 증대를 위해 생산 계획에 초점을 둔 제품으로 발전하였으나, 최근에는 수요자 중심으로의 비즈니스 패러다임 변화, 프로세스 간 상호연계 강화, 수요의 다양성 및 변동성 증가 등의 환경이 변화하면서 지능적인 SCM이 요구되고 있다. 지능적인 SCM은 IoT, 빅데이터, 인공지능 등의 기술을 활용하여 공급 사슬 전체에 대한 자동화, 자율화, 연결성을 보장하는 것을 강조하고 있다. 따라서 본 논문에서는 급변하는 비즈니스 환경변화에 대응하여 공급 사슬 최적화를 달성하기 위해 IoT와 빅데이터 기반의 SCM 시스템에 관하여 연구하였다.

• Journal of the Korean Institute of Gas
• /
• v.26 no.5
• /
• pp.1-9
• /
• 2022

Selection of a suitable artificial lift is important in terms of efficient operation and economics for oil production. In general, process of well design includes the selection of artificial lift, but the oil recovery could be enhanced by use of hybrid system combined with two types of artificial lift method according to reservoir condition for oil production. Electric submersible pump (ESP), as a presentative artificial lift method, is a manner for supplying the pressure in the lower part of oil well by using of a multi-stage centrifugal pump with an electric energy. However, there is a disadvantage that has a limit to the application period because of mechanical defection on ESP. Accordingly, it is possible to reduce the shutdown time of production well by applying the ESP/Gas lift hybrid system, which is to switch to a gas lift when an ESP is defective. This study describes the effect of ESP/gas lift hybrid system compared with ESP method for a onshore horizontal well locating in the of Permian basin, USA. As a result of study, ESP/gas lift hybrid system could make more effective productivity than ESP method. Also, we quantitatively predicted how much economic benefit would be obtained when the hybrid system was applied in the production well.

• Journal of the Korean Institute of Gas
• /
• v.26 no.6
• /
• pp.24-29
• /
• 2022

This paper is a purpose to Analyze and study the failure examples for a engine oil leakage of camshaft bearing seal, poor contact by computer connector fin damage and vaporizer inferiority on LPG automotive. The first example, when the researcher disassembled the cylinder head of engine to establish the cause for oil leakage, he confirmed the engine oil leakage by damaged between the engine intake camshaft bearing and seal part. The second example, the connector fin of power source line that control the starting of a car supplied with engine computer. As a result, it found the fact that the engine operation stopped because of cutting of the power source by connector fin damage. The third example, it verified the engine incongruity phe cutting of the power source by connector fin damage. The third example, it verified the engine incongruity phenomenon as thd gas didn't flow the vaporizer by foreign substance deposit. Finally, it supplied a small quantity gas from vaporizer to mix. As the computer controlling mix opening condition supplied a air as opening signal, the air and fuel became rarefied state. it knew that the engine didn't produce prpper power. Therefore, a car have to throughtly inspect not in order to arise the failure symptoms.

• The Journal of the Korea Contents Association
• /
• v.15 no.4
• /
• pp.490-499
• /
• 2015

In this study, for the introduction factors of ERP system suggested in the prior study, I analyzed the importance of each introduction factor by using Delphi methodology and AHP. As a result of analysing the importance of the introduction factors of the 1st layer, the supplier factor was analyzed to be the most important factor among innovation factor, information technology factor, the user factor, the supplier factor, and in the weight analysis on the 2nd layer considering the importance of 1st layer, the standard work model of the supplier factor was a suitable factor, and the CEO participation factor(.086) was analyzed as the second most important introduction factor. These analysis results enable to determine that domestic Small & Medium enterprises' position hope to introduce by selecting a system in which the company characteristics and management strategies are applied well, because they should operate an ERP system that has already been developed, and in this course, the participation of CEO was also found to be a very important factor.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.116.1-116.1
• /
• 2010

저급 연료원인 오일샌드는 아스팔트와 같은 중질유를 10% 이상 함유한 모래 또는 사암으로서, 겉으로는 시커먼 흙이나 모래처럼 보이나 내부에는 bitumen, 모래(점토) 및 물 등이 광물질 70~80%, bitumen 10~18%, 물 3~5% 정도의 비율로 혼합되어 있는데, 가열 또는 용매 추출 방식으로 오일샌드에 포함되어 있는 bitumen을 분리하여 정제하면 원유를 생산할 수 있으므로 고유가 시대의 대체에너지원으로 세계적인 석유회사들이 개발을 진행하고 있다. 따라서, 본 연구에서는 이러한 저급 연료원인 오일샌드 bitumen의 활용기술 개발을 위하여 기초특성 분석 결과 bitumen과 가장 유사한 특성을 가지는 것으로 파악된 중질잔사유를 대상으로 가스화를 통한 액체연료 전환을 위해 고점도 시료공급장치, 가스화기, 집진장치, 탈황장치, 수성가스 전환장치, 합성가스 압축장치, DME 전환장치 등으로 구성되는 시스템을 구축한 후 시험을 진행하였다.

• Tribology and Lubricants
• /
• v.20 no.3
• /
• pp.119-124
• /
• 2004

Engine bearing system is generally affected by aeration. In this paper, the aeration effects on the engine crankshaft bearing system were studied. To do this, unsteady oil flow analysis on the engine crankshaft oil circuit system was carried out. And aeration effects on the bearing system were simulated to figure out lubrication characteristics of the each bearing such as oil flow rate, minimum oil film thickness, friction loss and increase of oil temperature.