• Journal of the Korea Concrete Institute
• /
• v.27 no.2
• /
• pp.185-193
• /
• 2015

Ultra high performance concrete (UHPC) has been developed to overcome the low tensile strengths and brittleness of conventional concrete. Considering that UHPC, owing to its composition and the use of steel fibers, develops a compressive strength of 180 MPa as well as high stiffness, the top flange of the steel girder may be superfluous in the composite beam combining a slab made of UHPC and the steel girder. In such composite beam, the steel girder takes the form of an inverted-T shaped structure without top flange in which the studs needed for the composition of the steel girder with the UHPC slab are disposed in the web of the steel girder. This study investigates experimentally and analytically the flexural behavior of this new type of composite beam to propose details like stud spacing and slab thickness for further design recommendations. To that goal, eight composite beams with varying stud spacing and slab thickness were fabricated and tested. The test results indicated that stud spacing running from 100 mm to 2 to 3 times the slab thickness can be recommended. In view of the relative characteristic slip limit of Eurocode-4, the results showed that the composite beam developed ductile behavior. Moreover, except for the members with thin slab and large stud spacing, most of the specimens exhibited results different to those predicted by AASHTO LRFD and Eurocode-4 because of the high performance developed by UHPC.

• Korean Journal of Food Science and Technology
• /
• v.53 no.5
• /
• pp.607-612
• /
• 2021

This study investigated the seed and water absorption characteristics of red bean cultivars in Korea. The length and width of all seeds were 7.74-8.99 mm and 5.33-5.54 mm, respectively. The hilum lengths and widths were 3.21-4.01 mm and 0.58-0.73 mm, respectively. The weight of 100 seeds was 12.14-20.21 g, and the seed coat thickness of red beans ranged from 39.18-50.01 mm. During soaking for 30 h, red beans exhibited a lag phase in the initial soaking time, followed by a rapid absorption phase, and finally contained more than 130% moisture. When water absorption was applied to the sigmoid equation, the curve fitting exhibited a high R², and the kinetics of water absorption were 0.202-0.715 h^-1, which differed among varieties. Pearson's correlation of hilum width (r=0.7858^*) and seed thickness (r= -0.9954^***) exhibited strong correlations with water absorption, suggesting that these are important factors in red bean processing.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.46 no.3
• /
• pp.96-104
• /
• 2009

In this paper, we propose a no-reference objective Quality assessment metrics of image. The blockiness and blurring of edge areas which are sensitive to the human visual system are modeled as step functions. Blocking and blur metrics are obtained by estimating local visibility of blockiness and edge width, For the blocking metric, horizontal and vertical blocking lines are first determined by accumulating weighted differences of adjacent pixels and then the local visibility of blockiness at the intersection of blocking lines is obtained from the total difference of amplitudes of the 2-D step function which is modelled as a blocking region. The blurred input image is first re-blurred by a Gaussian blur kernel and an edge mask image is generated. In edge blocks, the local edge width is calculated from four directional projections (horizontal, vertical and two diagonal directions) using local extrema positions. In addition, the kurtosis and SSIM are used to compute the blur metric. The final no-reference objective metric is computed after those values are combined using an appropriate function. Experimental results show that the proposed objective metrics are highly correlated to the subjective data.

• Journal of Soil and Groundwater Environment
• /
• v.11 no.2
• /
• pp.1-12
• /
• 2006

A model describing the distributions of surfactants and HOCs (hydrophobic organic chemicals) in surfactant/HOC/activated carbon systems for surfactant reuse in soil washing process was developed. The model simulation was conducted for the evaluation of the effect of concentrations of surfactant, HOC, or activated carbons. Phenanthrene as a target HOC, Triton X-100 as surfactant and three granular activated carbons with different particle sizes (4-12, 12-20, and 20-40 mesh) were used in the model simulation. The distributions of HOC were significantly affected by surfactant dosages, especially at around the CMC(s). The results of selectivities for phenanthrene were much larger than 1 at various concentrations of surfactants, phenanthrene and activated carbons, which mean that the selective adsorption of phenanthrene by activated carbons is a proper separation method from surfactant solution. The model can be applied for the design of the surfactant reuse process using activated carbons without extra experimental efforts.

• Journal of Soil and Groundwater Environment
• /
• v.13 no.1
• /
• pp.32-42
• /
• 2008

A surfactant recovery and reuse process by selective adsorption with activated carbon was proposed to reduce surfactant cost in a soil washing process. Mathematical model simulation was performed for the whole process, which consists of soil washing, soil recovery, and soil re-washing. The optimal range of surfactant dosage was $6{\sim}10$-fold critical micelle concentration in soil. The efficiency of surfactant reuse process was decreased with increasing the dosage of activated carbon. Effectiveness factor for activated carbon significantly altered the efficiency of the reuse process unlike effectiveness factor for soil. Total requirement of surfactant was reduced to 20-30% with the reuse process compared to the conventional soil washing process. The contamination of wastewater after soil washing was reduced with the reuse process. This mathematical model can be used to estimate performance of the whole process of soil washing including surfactant recovery and to obtain optimal ranges of operating conditions without extra labor-intensive experimental works.

• Economic and Environmental Geology
• /
• v.45 no.3
• /
• pp.307-315
• /
• 2012

In this paper, a laboratory model test was conducted to evaluate grouting efficiency of ordinary portland cement(OPC) and micro cement used in MIS(Micro-Injection Process System). For this research, a injection equipment was developed for pressure permeation which can evenly simulate various grouting tests in a laboratory and suggested a standard for the production of the test specimen. Using the injection device, the laboratory injection tests of grouts were prepared with water/cement ratio of 1:1, 2:1, 3:1, 4:1, and 5:1. The analysis of injection test for pressure permeation showed that the efficiency of injection increases linearly as the water/cement ratio increases. Comparison of efficiency of the injection indicates that MIS with a relatively smaller average diameter shows more efficient injection than the OPC. In the low ratio of water/cement as 2:1~1:1, the injection efficiency of OPC was especially poor. Also, a nonlinear grout volume-injection time is represented by a hyperbolic model and grout volume predicted by hyperbolic model was compared with the value measured. From the comparison, it shows that the hyperbolic model has the potential of evaluating the efficiency of grouting.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.2
• /
• pp.111-118
• /
• 2013

This paper suggested the improvement of marine environmental impact assessment in eastern coast as analyzing consultation on the coastal area utilization for development of ports and fishing harbors for 3years in the east coast. The results of survey are only 3cases, 12cases and 16cases each for ocean currents, wave and sounding data. However, for development of ports and fishing harbors in eastern coast, ocean characteristics in eastern coast different than in the West Sea, South Sea is considered to marine environmental impact assessment. For development of ports and fishing harbors in east coast where the influences of ocean currents, wind-driven current and waves are dominant, the effect of the current should be considered to improve the reproducibility of tidal current. The wave should also be considered as an assessment criteria to obtain the validity of project such as harbor tranquility, functionality of breakwaters and stability. In addition, sediment inflow in river and exact water depth data of the ocean should be applied to numerical modeling and set wave-induced current to external force of sediment transport to predict the problems such as the harbor siltation and the coastal erosion considering ocean characteristics in the east coast.

• Journal of Bio-Environment Control
• /
• v.22 no.4
• /
• pp.316-321
• /
• 2013

This study was carried out to analyze heat transfer characteristics and heat flow through air-inflated double layer PO film with thermal resistance method. The experiments was conducted in the laboratory controlled air temperature between 258.0 K and 278.0 K. The experimental materials were made up two layers PO film and an inflated-air layer. The thickness of air-inflated layer was fixed at 3 types of 110, 175, 225 mm. The electrical circuit analogy for heat transfer by conduction, radiation and convection was introduced. Experimental data shows that the dominant thermal resistance in heat transfer through the air-inflated double layer film was convection. Calculation errors were 1.1~18.5 W for heat flow. In result, the method of thermal resistance could be introduced for analysis of heat flow characteristics through air-inflated double layer film.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.154-160
• /
• 2020

This study analyzed the fire intensity according to the zones classification between traditional market stores using FDS software. Modeling was conducted for the Seomoon traditional market district 4 at Daegu, which places combustibles, such as textiles and clothing near the passageway. The first ignition point assumed a short circuit fire situation at the fourth store combustible. The analysis was conducted under similar conditions as the fire situation in 2016. When there was no section wall, the fire spread rapidly through radiation in all directions from the fire-origin point. After 600 seconds, the mall was burnt to the ground. When section walls were present, however, the fire could be restricted inside the compartment. The first intensity of the two analysis conditions was predicted from the total heat energy from 200 seconds (X₁) to 600 seconds (X₂), where the heat generation rate began to increase rapidly. As a result of installing section walls near the fire point, heat energy generation of approximately 11.12 MW (55.68 %) was delayed. Further analysis of smoke control, according to the section wall arrangement and re-installation facilities, will be needed to study the characteristics of fire in traditional markets comprehensively.

• KIPS Transactions on Computer and Communication Systems
• /
• v.9 no.10
• /
• pp.239-246
• /
• 2020

In the medical field where artificial intelligence technology is introduced, research related to clinical decision support system(CDSS) in relation to diagnosis and prediction is actively being conducted. In particular, medical imaging-based disease diagnosis area applied AI technologies at various products. However, medical imaging data consists of inconsistent data, and it is a reality that it takes considerable time to prepare and use it for research. This paper describes a one-stop AI learning platform for converting to medical image standard R_CDM(Radiology Common Data Model) and supporting AI algorithm development research based on the dataset. To this, the focus is on linking with the existing CDM(common data model) and model the system, including the schema of the medical imaging standard model and report information for multi-center research based on DICOM(Digital Imaging and Communications in Medicine) tag information. And also, we show the execution results based on generated datasets through the AI learning platform. As a proposed platform, it is expected to be used for various image-based artificial intelligence researches.